A new and highly efficient cathode interlayer material for organic photovoltaics (OPVs) was produced by integrating C60fullerene monomers into ionene polymers. The power of these novel “C60‐ionenes” for interface modification enables the use of numerous high work‐function metals (e.g., silver, copper, and gold) as the cathode in efficient OPV devices. C60‐ionene boosted power conversion efficiencies (PCEs) of solar cells, fabricated with silver cathodes, from 2.79 % to 10.51 % for devices with a fullerene acceptor in the active layer, and from 3.89 % to 11.04 % for devices with a non‐fullerene acceptor in the active layer, demonstrating the versatility of this interfacial layer. The introduction of fullerene moieties dramatically improved the conductivity of ionene polymers, affording devices with high efficiency by reducing charge accumulation at the cathode/active layer interface. The power of C60‐ionene to improve electron injection and extraction between metal electrodes and organic semiconductors highlights its promise to overcome energy barriers at the hard‐soft materials interface to the benefit of organic electronics.
Organic photovoltaic cells possess desirable practical characteristics, such as the potential for low‐cost fabrication on flexible substrates, but they lag behind their inorganic counterparts in performance due in part to fundamental energy loss mechanisms, such as overcoming the charge transfer (CT) state binding energy when photogenerated charge is transferred across the donor/acceptor interface. However, recent work has suggested that crystalline interfaces can reduce this binding energy due to enhanced CT state delocalization. Solar cells based on rubrene and C60are investigated as an archetypal system because it allows the degree of crystallinity to be moldulated from a highly disordered to highly ordered system. Using a postdeposition annealing method to transform as‐deposited amorphous rubrene thin films into ones that are highly crystalline, it is shown that the CT state of a highly crystalline rubrene/C60heterojunction undergoes extreme delocalization parallel to the interface leading to a band‐like state that exhibits a linear Stark effect. This state parallels the direct charge formation of inorganic solar cells and reduces energetic losses by 220 meV compared with 12 other archetypal heterojunctions reported in the literature.
more » « less- PAR ID:
- 10047918
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Advanced Energy Materials
- Volume:
- 8
- Issue:
- 9
- ISSN:
- 1614-6832
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
Abstract -
more » « less
Abstract A new and highly efficient cathode interlayer material for organic photovoltaics (OPVs) was produced by integrating C60fullerene monomers into ionene polymers. The power of these novel “C60‐ionenes” for interface modification enables the use of numerous high work‐function metals (e.g., silver, copper, and gold) as the cathode in efficient OPV devices. C60‐ionene boosted power conversion efficiencies (PCEs) of solar cells, fabricated with silver cathodes, from 2.79 % to 10.51 % for devices with a fullerene acceptor in the active layer, and from 3.89 % to 11.04 % for devices with a non‐fullerene acceptor in the active layer, demonstrating the versatility of this interfacial layer. The introduction of fullerene moieties dramatically improved the conductivity of ionene polymers, affording devices with high efficiency by reducing charge accumulation at the cathode/active layer interface. The power of C60‐ionene to improve electron injection and extraction between metal electrodes and organic semiconductors highlights its promise to overcome energy barriers at the hard‐soft materials interface to the benefit of organic electronics.
-
more » « less
Abstract Organometal halide perovskites have powerful intrinsic potential to drive next‐generation solar technology, but their insufficient thermomechanical reliability and unproven large‐area manufacturability limit competition with incumbent silicon photovoltaics. This work addresses these limitations by leveraging large‐area processing and robust inorganic hole transport layers (HTLs). Inverted perovskite solar cells utilizing NiOxHTLs deposited by rapid aqueous spray‐coating that outperform spin‐coated NiOxand lead to a 5× improvement in the fracture energy (
G c), a primary metric of thermomechanical stability, are presented. The morphology, chemical composition, and optoelectronic properties of the NiOxfilms are characterized to understand and optimize compatibility with an archetypal double cation perovskite, Cs.17FA.83Pb(Br.17I.83)3. Perovskite solar cells with sprayed NiOxshow higher photovoltaic performance, exhibiting up to 82% fill factor and 17.7% power conversion efficiency (PCE)—the highest PCE reported for inverted cell with scalable charge transport layers—as well as excellent stability under full illumination and after 4000 h aging in inert conditions at room temperature. By utilizing open‐air techniques and aqueous precursors, this combination of robust materials and low‐cost processing provides a platform for scaling perovskite modules with long‐term reliability. -
more » « less
Abstract Inorganic perovskite solar cells (IPSCs) have gained significant attention due to their excellent thermal stability and suitable band gap (~1.7 eV) for tandem solar cell applications. However, the defect‐induced non‐radiative recombination losses, low charge extraction efficiency, energy level mismatches, and so on render the fabrication of high‐efficiency inverted IPSCs remains challenging. Here, the use of 3‐amino‐5‐bromopyridine‐2‐formamide (ABF) in methanol was dynamically spin‐coated on the surface of CsPbI2.85Br0.15film, which facilitates the limited etching of defect‐rich subsurface layer, resulting in the formation of vertical PbI2nanosheet structures. This enabled localized contacts between the perovskite film and the electron transport layer, suppress the recombination of electron‐hole and beneficial to electron extraction. Additionally, the C=O and C=N groups in ABF effectively passivated the undercoordinated Pb2+at grain boundaries and on the surface of CsPbI2.85Br0.15film. Eventually, we achieved a champion efficiency of 20.80 % (certified efficiency of 20.02 %) for inverted IPSCs with enhanced stability, which is the highest value ever reported to date. Furthermore, we successfully prepared p‐i‐n type monolithic inorganic perovskite/silicon tandem solar cells (IPSTSCs) with an efficiency of 26.26 %. This strategy provided both fast extraction and efficient passivation at the electron‐selective interface.
-
more » « less
Abstract Inorganic perovskite solar cells (IPSCs) have gained significant attention due to their excellent thermal stability and suitable band gap (~1.7 eV) for tandem solar cell applications. However, the defect‐induced non‐radiative recombination losses, low charge extraction efficiency, energy level mismatches, and so on render the fabrication of high‐efficiency inverted IPSCs remains challenging. Here, the use of 3‐amino‐5‐bromopyridine‐2‐formamide (ABF) in methanol was dynamically spin‐coated on the surface of CsPbI2.85Br0.15film, which facilitates the limited etching of defect‐rich subsurface layer, resulting in the formation of vertical PbI2nanosheet structures. This enabled localized contacts between the perovskite film and the electron transport layer, suppress the recombination of electron‐hole and beneficial to electron extraction. Additionally, the C=O and C=N groups in ABF effectively passivated the undercoordinated Pb2+at grain boundaries and on the surface of CsPbI2.85Br0.15film. Eventually, we achieved a champion efficiency of 20.80 % (certified efficiency of 20.02 %) for inverted IPSCs with enhanced stability, which is the highest value ever reported to date. Furthermore, we successfully prepared p‐i‐n type monolithic inorganic perovskite/silicon tandem solar cells (IPSTSCs) with an efficiency of 26.26 %. This strategy provided both fast extraction and efficient passivation at the electron‐selective interface.
