To understand the mechanism underlying the fast, reversible, phase transformation, information about the atomic structure and defects structures in phase change materials class is key. PCMs are investigated for many applications. These devices are chalcogenide based and use self heating to quickly switch between amorphous and crystalline phases, generating orders of magnitude differences in the electrical resistivity. The main challenges with PCMs have been the large power required to heat above crystallization or melting (for melt-quench amorphization) temperatures and limited reliability due to factors such as resistance drifts of the metastable phases, void formation and elemental segregation upon cycling. Characterization of devices and their unique switching behavior result in distinct material properties affected by the atomic arrangement in the respective phase. TEM is used to study the atomic structure of the metastable crystalline phase. The aim is to correlate the microstructure with results from electrical characterization, building on R vs T measurements on various thicknesses GST thin films.
To monitor phase changes in real-time as a function of temperature, thin films are deposited directly onto Protochips carriers. The Protochips heating holders provides controlled temperature changes while imaging in the TEM. These studies can provide insights into how changes occur in the various phase transformations even though the rate of temperature change is much slower than the PCM device operation. Other critical processes such as void formation, grain evolution and the cause of resistance drift can thereby be related to changes in structure and chemistry. Materials characterization is performed using Tecnai F30 and Titan ETEM microscopes, operating at 300kV. Both the microscopes can accept the same Protochips heating holders. The K2 direct electron detector camera equipped with the ETEM allows high-speed video recording (1600 f/s) of structural changes occurring in these materials upon heating and cooling. In this presentation, we will describe the effect of heating thin films of different thickness and composition, the changes in crystallinity and grain size, and how these changes correlate with changes in the electrical properties of the films. We will emphasize that it is always important to use low-dose and/or beam blanking techniques to distinguish changes induced by the beam from those due to the heating or introduction of an electric current.
more »
« less
Self‐Healing of a Confined Phase Change Memory Device with a Metallic Surfactant Layer
Understanding and possibly recovering from the failure mechanisms of phase change memories (PCMs) are critical to improving their cycle life. Extensive electrical testing and postfailure electron microscopy analysis have shown that stuck–set failure can be recovered. Here, self‐healing of novel confined PCM devices is directly shown by controlling the electromigration of the phase change material at the nanoscale. In contrast to the current mushroom PCM, the confined PCM has a metallic surfactant layer, which enables effective Joule heating to control the phase change material even in the presence of a large void. In situ transmission electron microscope movies show that the voltage polarity controls the direction of electromigration of the phase change material, which can be used to fill nanoscale voids that form during programing. Surprisingly, a single voltage pulse can induce dramatic migration of antimony (Sb) due to high current density in the PCM device. Based on the finding, self‐healing of a large void inside a confined PCM device with a metallic liner is demonstrated for the first time.
more » « less- NSF-PAR ID:
- 10049470
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Advanced Materials
- Volume:
- 30
- Issue:
- 9
- ISSN:
- 0935-9648
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
more » « less
Abstract Metasurfaces control light propagation at the nanoscale for applications in both free-space and surface-confined geometries. However, dynamically changing the properties of metasurfaces can be a major challenge. Here we demonstrate a reconfigurable hyperbolic metasurface comprised of a heterostructure of isotopically enriched hexagonal boron nitride (hBN) in direct contact with the phase-change material (PCM) single-crystal vanadium dioxide (VO2). Metallic and dielectric domains in VO2provide spatially localized changes in the local dielectric environment, enabling launching, reflection, and transmission of hyperbolic phonon polaritons (HPhPs) at the PCM domain boundaries, and tuning the wavelength of HPhPs propagating in hBN over these domains by a factor of 1.6. We show that this system supports in-plane HPhP refraction, thus providing a prototype for a class of planar refractive optics. This approach offers reconfigurable control of in-plane HPhP propagation and exemplifies a generalizable framework based on combining hyperbolic media and PCMs to design optical functionality.
-
Phase-change memory (PCM) materials are being developed for faster, non-volatile & high-density memory that can facilitate more efficient computation as well as data storage. The materials used for these PCM devices are usually chalcogenides that can be switched between their amorphous and crystalline phases thus producing orders of magnitude difference in the electrical resistivity [1, 2]. The operation of such devices is limited by elemental segregation and void formation, which occurs as a result of the extensive cycling. After crystallization, the structure gradually transforms from fcc to hexagonal. In the present work, we are studying these different phase changes in-situ as they occur in PCM materials basically using TEM imaging. The aim is to correlate device modeling and electrical characterization in order to improve the models and enable accurate, predictive simulations. The thin film materials and devices can be directly deposited onto Protochips devices, allowing controlled temperature changes while imaging in the TEM. Although the temperature change rate achievable is too slow as compared to the fastest PCM-device operation, these rates can provides valuable insights into the various property changes in the material and phase transformations as well. Both a Cs-image corrected Titan ETEM and a Tecnai F30 have been used for this study. The ETEM is equipped with a K2 direct electron detector camera allowing high-speed video recording of these PCM materials.more » « less
-
more » « less
Abstract The emergence of spin‐orbit torques as a promising approach to energy‐efficient magnetic switching has generated large interest in material systems with easily and fully tunable spin‐orbit torques. Here, current‐induced spin‐orbit torques in VO2/NiFe heterostructures are investigated using spin‐torque ferromagnetic resonance, where the VO2layer undergoes a prominent insulator‐metal transition. A roughly twofold increase in the Gilbert damping parameter, α, with temperature is attributed to the change in the VO2/NiFe interface spin absorption across the VO2phase transition. More remarkably, a large modulation (±100%) and a sign change of the current‐induced spin‐orbit torque across the VO2phase transition suggest two competing spin‐orbit torque generating mechanisms. The bulk spin Hall effect in metallic VO2, corroborated by the first‐principles calculation of the spin Hall conductivity , is verified as the main source of the spin‐orbit torque in the metallic phase. The self‐induced/anomalous torque in NiFe, with opposite sign and a similar magnitude to the bulk spin Hall effect in metallic VO2, can be the other competing mechanism that dominates as temperature decreases. For applications, the strong tunability of the torque strength and direction opens a new route to tailor spin‐orbit torques of materials that undergo phase transitions for new device functionalities.
-
more » « less
The temperature coefficient of resistivity (θT) of carbon-based materials is a critical property that directly determines their electrical response upon thermal impulses. It could have metal- (positive) or semiconductor-like (negative) behavior, depending on the combined temperature dependence of electron density and electron scattering. Its distribution in space is very difficult to measure and is rarely studied. Here, for the first time, we report that carbon-based micro/nanoscale structures have a strong non-uniform spatial distribution of θT. This distribution is probed by measuring the transient electro-thermal response of the material under extremely localized step laser heating and scanning, which magnifies the local θT effect in the measured transient voltage evolution. For carbon microfibers (CMFs), after electrical current annealing, θT varies from negative to positive from the sample end to the center with a magnitude change of >130% over <1 mm. This θT sign change is confirmed by directly testing smaller segments from different regions of an annealed CMF. For micro-thick carbon nanotube bundles, θT is found to have a relative change of >125% within a length of ∼2 mm, uncovering strong metallic to semiconductive behavior change in space. Our θT scanning technique can be readily extended to nm-thick samples with μm scanning resolution to explore the distribution of θT and provide a deep insight into the local electron conduction.
