For piezoelectric energy harvesters, a large volume of piezoelectric material with a high figure of merit is essential to obtain a higher power density. The work describes the growth of highly (001) oriented sputtered lead zirconate titanate (PZT) films (
Vibration‐based energy harvesting for enabling next‐generation self‐powered devices is a rapidly growing research area. In real‐world applications, the ambient vibrational energy is often available in non‐deterministic forms rather than the extensively studied deterministic scenarios, such as simple harmonic excitation. It is of interest to choose the best piezoelectric material for a given random excitation. Here, performance comparisons of various soft and hard piezoelectric ceramics and single crystals are presented for electrical power generation under band‐limited off‐resonance and wideband random vibration energy‐harvesting scenarios. For low‐frequency off‐resonance excitation, it is found that soft piezoelectric ceramics based upon lead zirconate titanate (e.g., PZT‐5H and PZT‐5A) outperform their hard counterparts (e.g., PZT‐4 and PZT‐8), and likewise soft single crystals based upon lead magnesium niobate and lead titanate as well as PZT (e.g., PMN‐PT and PMN‐PZT) outperform the relatively hard ones (e.g., manganese‐doped PMN‐PZT‐Mn). Overall, for such off‐resonance random vibrations, PMN‐PT is the most suitable choice among the materials studied. For wideband random excitation with a bandwidth covering the fundamental resonance of the harvester, hard piezoelectric ceramics offer larger power output compared to soft ceramics, and likewise hard single crystals produce larger power compared to their soft counterparts. Remarkably, a hard piezoelectric ceramic (e.g., PZT‐8) can outperform a soft single crystal (e.g., PMN‐PT) for wideband random vibration energy harvesting.
more » « less- NSF-PAR ID:
- 10054055
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Energy Technology
- Volume:
- 6
- Issue:
- 5
- ISSN:
- 2194-4288
- Page Range / eLocation ID:
- p. 935-942
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
Abstract f ≈ 0.99) exceeding 4 µm in thickness on both sides of an Ni foil to produce a bimorph structure. These films are incorporated in novel wrist‐worn energy harvesters (<16 cm2) in which piezoelectric beams are plucked magnetically using an eccentric rotor with embedded magnets to implement frequency up‐conversion. The resulting devices successfully convert low‐frequency vibration sources (i.e., from walking, rotating the wrist, and jogging) to higher frequency vibrations of the PZT beams (100–200 Hz). Measured at resonance, six beams producing an output of 1.2 mW is achieved at 0.15 G acceleration. For magnetic plucking of a wrist‐worn nonresonant device, 40–50 µW is produced during mild activity. -
Lead zirconate titanate (PZT) is widely used in energy harvesting because of its excellent material properties. However, as the material contains lead, there are significant environmental concerns with its production and use. Flexoelectricity refers to the coupling between strain gradient and electric polarization that exists, in principle, in all dielectric materials and would allow for energy harvesting without using piezoelectric materials. However, the effect is very weak in most materials. Promisingly, it has recently been shown that space charge polarized materials (i.e., semiconducting materials with insulating barrier layers) can exhibit enhanced flexoelectricity. This space charge induced flexoelectric effect opens up the possibility of a non-toxic replacement for PZT in energy harvesting applications. In this paper we investigate the use of doped silicon with hafnium oxide insulating layers as flexoelectric transducers that could replace PZT in many applications including energy harvesting. Specifically, we experimentally demonstrate flexoelectricity in a bending beam and show an effective flexoelectric coefficient of 4.9 uC/F. Finally, we develop and demonstrate a finite element model for flexoelectricity.more » « less
-
more » « less
Abstract Piezoelectric materials should simultaneously possess the soft properties (high piezoelectric coefficient,
d 33; high voltage coefficient,g 33; high electromechanical coupling factor,k ) and hard properties (high mechanical quality factor,Q m; low dielectric loss, tan δ) along with wide operation temperature (e.g., high rhombohedral–tetragonal phase transition temperatureT r–t) for covering off‐resonance (figure of merit (FOM),d 33 ×g 33) and on‐resonance (FOM,Q m ×k 2) applications. However, achieving hard and soft piezoelectric properties simultaneously along with high transition temperature is quite challenging since these properties are inversely related to each other. Here, through a synergistic design strategy of combining composition/phase selection, crystallographic texturing, defect engineering, and water quenching technique, <001> textured 2 mol% MnO2doped 0.19PIN‐0.445PSN‐0.365PT ceramics exhibiting giant FOM values ofQ m × (227–261) along with highd 33 ×g 33(28–35 × 10−12m2N−1), low tan δ (0.3–0.39%) and highT r–tof 140–190 °C, which is far beyond the performance of the state‐of‐the‐art piezoelectric materials, are fabricated. Further, a novel water quenching (WQ) room temperature poling technique, which results in enhanced piezoelectricity of textured MnO2doped PIN‐PSN‐PT ceramics, is reported. Based upon the experiments and phase‐field modeling, the enhanced piezoelectricity is explained in terms of the quenching‐induced rhombohedral phase formation. These findings will have tremendous impact on development of high performance off‐resonance and on‐resonance piezoelectric devices with high stability. -
more » « less
Abstract Piezoelectric materials enable the conversion of mechanical energy into electrical energy and vice‐versa. Ultrahigh piezoelectricity has been only observed in single crystals. Realization of piezoelectric ceramics with longitudinal piezoelectric constant (
d 33) close to 2000 pC N–1, which combines single crystal‐like high properties and ceramic‐like cost effectiveness, large‐scale manufacturing, and machinability will be a milestone in advancement of piezoelectric ceramic materials. Here, guided by phenomenological models and phase‐field simulations that provide conditions for flattening the energy landscape of polarization, a synergistic design strategy is demonstrated that exploits compositionally driven local structural heterogeneity and microstructural grain orientation/texturing to provide record piezoelectricity in ceramics. This strategy is demonstrated on [001]PC‐textured and Eu3+‐doped Pb(Mg1/3Nb2/3)O3‐PbTiO3(PMN‐PT) ceramics that exhibit the highest piezoelectric coefficient (small‐signald 33of up to 1950 pC N–1and large‐signald 33* of ≈2100 pm V–1) among all the reported piezoelectric ceramics. Extensive characterization conducted using high‐resolution microscopy and diffraction techniques in conjunction with the computational models reveals the underlying mechanisms governing the piezoelectric performance. Further, the impact of losses on the electromechanical coupling is identified, which plays major role in suppressing the percentage of piezoelectricity enhancement, and the fundamental understanding of loss in this study sheds light on further enhancement of piezoelectricity. These results on cost‐effective and record performance piezoelectric ceramics will launch a new generation of piezoelectric applications. -
This paper presents a system for vibration and thermal energy harvesting from automobiles, and it intends to power wireless sensor nodes. Two main features of the proposed circuit are impedance matching to extract maximum power and wake-up to incorporate sleep mode. Two separate buck-boost converters in discontinuous conduction mode are used for impedance matching. A wake-up circuit senses the vibration energy generated by a piezoelectric cantilever (PZT). When a car is turned off, the wake-up circuit deactivates the two converters, and the entire circuit goes into sleep mode to save power. The proposed circuit charges a capacitor to power a wireless sensor node, and is able to cold start. The proposed circuit is prototyped with discrete components. Experimental results show that the proposed system harvests peak power of 3.4 mW and these results also demonstrate that a wireless sensor node can be powered by the proposed system.more » « less
