An electric field‐assisted
Cellulose nanocrystal (CNCs)‐reinforced poly(lactic acid) (PLA) nanocomposites were prepared using twin screw extrusion followed by injection molding. Masterbatch approach was used to achieve more efficient dispersion of CNCs in PLA matrix. Modified CNCs (b‐CNCs) were prepared using benzoic acid as a nontoxic material through a green esterification method in a solvent‐free technique. Transmission electron microscopy images did not exhibit significant differences in the structure of b‐CNCs as compared with unmodified CNCs. However, a reduction of 6.6–15.5% in the aspect ratio of b‐CNCs was observed. The fracture surface of PLA‐b‐CNCs nanocomposites exhibited rough and irregular pattern which confirmed the need of more energy for fracture. Pristine CNCs showed a decrease in the thermal stability of nanocomposites, however, b‐CNCs nanocomposites exhibited higher thermal stability than pure PLA. The average storage modulus was improved by 38 and 48% by addition of CNCs and b‐CNCs in PLA, respectively. The incorporation of b‐CNCs increased Young's modulus, ultimate tensile stress, elongation at break, and impact strength by 27.02, 10.90, 4.20, and 32.77%, respectively, however, CNCs nanocomposites exhibited a slight decrease in ultimate strength and elongation at break. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci.
- PAR ID:
- 10055199
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Journal of Applied Polymer Science
- Volume:
- 135
- Issue:
- 27
- ISSN:
- 0021-8995
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
ABSTRACT in situ dispersion of multiwall carbon nanotubes (MWCNTs) in polymer nanocomposites, fabricated through stereolithography three‐dimensional (3D) printing technique, was demonstrated. The introduction of MWCNTs increased the elasticity modulus of the polymer resin by 77%. Furthermore, the use of an electric field forin situ MWCNT dispersion helped improving the average elongation at break of the samples with MWCNTs by 32%. The electric field also increased the ultimate tensile strength of the MWCNT reinforced nanocomposites by 42%. An increase of over 20% in the ultimate tensile strength ofin situ dispersed MWCNT nanocomposites over the pure polymer material was observed. Finally, it was demonstrated that the magnitude and direction of the electrical conductivity of MWCNT nanocomposites can be engineered through the application ofin situ electric fields during 3D printing. An increase of 50% in the electrical conductivity was observed when MWCNTs were introduced, while the application of the electric field further improved the electrical conductivity by 26%. The presented results demonstrated the feasibility of tuning both electrical and mechanical properties of MWCNT reinforced polymer nanocomposites usingin situ electrical field‐assisted 3D printing. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci.2019 ,136 , 47600. -
more » « less
Abstract Poly(lactic acid) (PLA) is a commercially available bio‐based polymer that is a potential alternative to many commodity petrochemical‐based polymers. However, PLA's thermomechanical properties limit its use in many applications. Incorporating polymer‐grafted cellulose nanocrystals (CNCs) is one potential route to improving these mechanical properties. One key challenge in using these polymer‐grafted nanoparticles is to understand which variables associated with polymer grafting are most important for improving composite properties. In this work, poly(ethylene glycol)‐grafted CNCs are used to study the effects of polymer grafting density and molecular weight on the properties of PLA composites. All CNC nanofillers are found to reinforce PLA above the glass transition temperature, but non‐grafted CNCs and CNCs grafted with short PEG chains (<2 kg mol−1) are found to cause significant embrittlement, generally resulting in less than 3% elongation‐at‐break. By grafting higher molecular weight PEG (10 kg mol−1) onto the CNCs at a grafting density where the polymer chains are predicted to be in the semi‐dilute polymer brush conformation (~0.1 chains nm−2), embrittlement can be avoided.
-
more » « less
ABSTRACT The thermal aging behavior of poly(3,3,3‐trifluoropropyl)methylsiloxane was investigated by thermal gravimetric analysis and isothermal aging tests, and the results indicated the degradation mechanism II, oxidation scission of the side groups, played a more important role when the temperature was below 350 °C. The addition of ceria had significantly improved the thermal stability of fluorosilicone rubber (FSR) by inhibiting the oxidation scission. Moreover, two types of ceria including laminar‐structure ceria (LS‐CeO2) and nanoparticle ceria (N‐CeO2) were prepared and surface was modified by KH570 and characterized by scanning electron microscopy, transmission electron microscope, and X‐ray diffractometer. FSR incorporated with modified LS‐CeO2and N‐CeO2revealed a significant improvement on the heat resistant properties. In particular, after having been thermal oxidative aged for 70 h at 250 °C, FSR containing 2 wt % of modified N‐CeO2maintained 72.6% of tensile strength and 63.9% of elongation at break, respectively, while FSR without ceria completely failed. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci.
2016 ,133 , 44117. -
more » « less
This experimental study investigates the effects of dispersion techniques on the mechanical properties of POSS‐epoxy nanocomposites. The POSS is dispersed into the epoxy resin by stoichiometrically varying the weight fraction from 0.5 to 10 wt% and materials are prepared using three different dispersion techniques. Various mechanical properties are reported as functions of processing parameters and weight fractions. It is found that the nanocomposites with highly dispersed POSS show higher modulus and toughness values. For example, nanocomposites prepared by ultrasonication show increases in elastic and flexural modulus values by average amounts of 23% and 15%, respectively. Also, it is found that fracture toughness values increased for all three processing techniques, with the highest increase by an average of 50% at 8 wt% of POSS inclusion for nanocomposites prepared by ultrasonication. TEM images of the nanocomposites demonstrate that the properties are also affected by the formation of soft domains at higher loading levels of POSS. Further evidence on the soft domains is found in the variations of
T g. FTIR spectroscopy shows evidence of SiOSi stretching, again suggesting the formation of compliant domains due to POSS‐POSS agglomeration. POLYM. COMPOS., 39:E2445–E2453, 2018. © 2018 Society of Plastics Engineers -
This work describes how a solid-state blending method such as jet milling can be used to successfully prepare polysulfone (PSU)/ γ -alumina nanocomposites. For comparison purposes, conventional melt extrusion was used as well. Morphological analysis revealed how jet mill blending allows obtaining well-dispersed γ -alumina nanoparticles within a polysulfone matrix without any surface treatment, with an important decrease of particle size promoted by the breakup of agglomerates and aggregates due to the particle-particle impacts during processing, which was not observed in the extruded nanocomposites. DSC analysis demonstrated that jet-milling processing promoted T g enhancements with alumina addition, while TGA experiments confirmed the increment of thermal stability of the nanocomposites prepared by jet milling when compared with the composites prepared by extrusion. The tensile tests showed that ductility remains at a high value for milled nanocomposites, which agreed with the fracture surface images revealing large plastic deformation as a function of the alumina content. This comparative study indicates that the dispersion of nanoparticles in PSU was more homogeneous, with smaller nanoparticles when preparing nanocomposites using jet milling, showing a strong correlation with the enhanced final properties of the nanocomposites.more » « less
