More Like this

1. Numerical Study of the Effects of Confinement on Concurrent-Flow Flame Spread in Microgravity

   https://doi.org/10.1115/1.4047645  

   Li, Yanjun; Liao, Ya-Ting T.; Ferkul, Paul (November 2020, Journal of Heat Transfer)

   null (Ed.)

   Abstract The objective of this work is to investigate the aerodynamics and thermal interactions between a spreading flame and the surrounding walls as well as their effects on fire behaviors. A three-dimensional transient computational fluid dynamics (CFD) combustion model is used to simulate concurrent-flow flame spread over a thin solid sample in a narrow flow duct. The height of the flow duct is the main parameter. The numerical results predict a quenching height for the flow duct below which the flame fails to spread. For duct heights sufficiently larger than the quenching height, the flame reaches a steady spreading state before the sample is fully consumed. The flame spread rate and the pyrolysis length at steady-state first increase and then decrease when the flow duct height decreases. The detailed gas and solid profiles show that flow confinement has multiple effects on the flame spread process. On one hand, it accelerates flow during thermal expansion from combustion, intensifying the flame. On the other hand, increasing flow confinement reduces the oxygen supply to the flame and increases conductive heat loss to the walls, both of which weaken the flame. These competing effects result in the aforementioned nonmonotonic trend of flame spread rate as duct height varies. Near the quenching duct height, the transient model reveals that the flame exhibits oscillation in length, flame temperature, and flame structure. This phenomenon is suspected to be due to thermodiffusive instability. 

   more » « less
2. Concurrent-Flow Flame Spread Over a Thin Solid in a Narrow Confined Space in Microgravity

   https://doi.org/10.1115/IMECE2019-11908  

   Li, Yanjun; Liao, Ya-Ting T.; Ferkul, Paul (November 2019, Proceedings of the ASME 2019 International Mechanical Engineering Congress and Exposition)

   null (Ed.)

   A numerical study is pursued to investigate the aerodynamics and thermal interactions between a spreading flame and the surrounding walls as well as their effects on fire behaviors. This is done in support of upcoming microgravity experiments aboard the International Space Station. For the numerical study, a three-dimensional transient Computational Fluid Dynamics combustion model is used to simulate concurrent-flow flame spread over a thin solid sample in a narrow flow duct. The height of the flow duct is the main parameter. The numerical results predict a quenching height for the flow duct below which the flame fails to spread. For duct heights sufficiently larger than the quenching height, the flame reaches a steady spreading state before the sample is fully consumed. The flame spread rate and the pyrolysis length at steady state first increase and then decrease when the flow duct height decreases. The detailed gas and solid profiles show that flow confinement has competing effects on the flame spread process. On one hand, it accelerates flow during thermal expansion from combustion, intensifying the flame. On the other hand, increasing flow confinement reduces the oxygen supply to the flame and increases conductive heat loss to the walls, both of which weaken the flame. These competing effects result in the aforementioned non-monotonic trend of flame spread rate as duct height varies. This work relates to upcoming microgravity experiments, in which flat thin samples will be burned in a low-speed concurrent flow using a small flow duct aboard the International Space Station. Two baffles will be installed parallel to the fuel sample (one on each side of the sample) to create an effective reduction in the height of the flow duct. The concept and setup of the experiments are presented in this work. 

   more » « less
3. Flame Spread Over Ultra-thin Solids: Effect of Area Density and Concurrent-Opposed Spread Reversal Phenomenon

   https://doi.org/10.1007/s10694-019-00878-w  

   Vetturini, Anthony; Cui, Wohan; Liao, Ya-Ting; Olson, Sandra; Ferkul, Paul (June 2019, Fire technology)

   There are no existing experimental studies of flame spread rate trends for ultra-thin solid samples. Previous theory has predicted that for concurrent flame in kinetic regime, the flame spread rate decreases as the sample thickness decreases and there is a critical thickness below which burning is not possible. To test this hypothesis, a series of microgravity experiments of concurrent-flow flame spread over samples of ultra-low area densities are conducted using NASA Glenn Research Center’s Zero Gravity Research Facility (the 5.18 s drop tower). The tested samples are cellulose-based materials of various area densities, ranging from 0.2 mg/cm2 to 13 mg/cm2, as low as one order of magnitude less than those ever tested before. Each sample is 30 cm long by 5 cm wide and is burned in a low-speed concurrent air flow (5 to 30 cm/s). The results show that the concurrent flame spread rate is proportional to the flow velocity relative to the flame and is inversely proportional to the sample area density. A theoretical formulation, provided in this work, suggests that the flame length has a linear relationship with the relative flow speed and has no direct dependency on the sample area density. The experimental data supports this conclusion. From the images recorded in the experiments, a unique flame base tubular structure directed upstream away from the burnout zone is observed for thin samples. This structure is suspected to be due to flame stretching and localized blowoff caused by the oxidative pyrolysis Stefan flows at the sample burnout. This can be an indication that the chemical time becomes comparable to the flow time of the Stefan flow and the tested samples are approaching the kinetically-limited thickness. For the thinnest tested sample (0.2 mg/cm2), flames with concurrent and opposed dual natures are observed when the air flow rate is low (< 20 cm/s). At the lowest tested flow rate (5 cm/s), the flame spread rate exceeds the air flow rate and the flame transits to an opposed flame in the concurrent flow. The dual nature and flame transition are presented and discussed. This study provides detailed examination through high-resolution images of the transition between the concurrent to opposed flame spread modes. 

   more » « less
4. Effects of spacing on flaming and smoldering firebrands in wildland–urban interface fires

   https://doi.org/10.1177/07349041221081998  

   Kwon, Byoungchul; Liao, Ya-Ting_T (March 2022, Journal of Fire Sciences)

   Firebrand (ember) attack has been shown to be one of the key mechanisms of wildfire spread into wildland–urban interface communities. After the firebrands land on a substrate material, the ignition propensity of the material depends on not only the attributes (e.g. shape, size, and numbers) but also the distribution of the firebrands. To help characterize this process, this study aims to investigate the effects of gap spacing on the burning behaviors of a group of wooden samples. Experiments are conducted using nine wooden cubes, 19 mm on each side. These samples are arranged in a 3 × 3 square pattern on suspension wires and are ignited by hot coils from the bottom surface. The gap spacing (s) between the samples varies in each test (ranging from 0 to 30 mm). After ignition, the samples are left to burn to completion. The burning process is recorded using video cameras. Sample mass loss and temperatures are monitored during the flaming and smoldering processes. The results show that the flame height and the sample mass loss rate have non-monotonic dependencies on the gap spacing. When the gap spacing reduces, the flame height and the mass loss rate first increase due to enhanced heat input from the adjacent flames to each sample. When s ≤ 10 mm, flames from individual samples are observed to merge into a single large fire. As s further decreases, the air entrainment at the flame bottom decreases and the flame lift-off distance at the flame center increases, resulting in an increased flame height, decreased flame heat feedback to the solid samples, and a decreased mass loss rate. The decreased mass loss rate eventually leads to a decrease in the flame height as well. The gaseous flame height is correlated to the solid burning rate. The correlation generally follows previous empirical equations for continuous fire sources. For the smoldering combustion, compared to a single burning sample, the smoldering temperature and duration significantly increase due to the thermal interactions between adjacent burning samples. To help interpret the results of the burning experiments, thermogravimetric analysis is also performed in air and nitrogen, resulting in heating rates ranging from 10 to 100 K/min. 

   more » « less
5. Pulsatile flow in a thin-walled viscoelastic tube

   https://doi.org/10.1017/jfm.2025.150  

   Krul, Oleksander; Bagchi, Prosenjit (March 2025, Journal of Fluid Mechanics)

   Low-inertia pulsatile flows in highly distensible viscoelastic vessels exist in many biological and engineering systems. However, many existing works focus on inertial pulsatile flows in vessels with small deformations. As such, here we study the dynamics of a viscoelastic tube at large deformation conveying low-Reynolds-number oscillatory flow using a fully coupled fluid–structure interaction computational model. We focus on a detailed study of the effect of wall (solid) viscosity and oscillation frequency on tube deformation, flow rate, phase shift and hysteresis, as well as the underlying flow physics. We find that the general behaviour is dominated by an elastic flow surge during inflation and a squeezing effect during deflation. When increasing the oscillation frequency, the maximum inlet flow rate increases and tube distention decreases, whereas increasing solid viscosity causes both to decrease. As the oscillation frequency approaches either$$0$$(quasi-steady inflation cycle) or$$\infty$$(steady flow), the behaviours of tubes with different solid viscosities converge. Our results suggest that deformation and flow rate are most affected in the intermediate range of solid viscosity and oscillation frequency. Phase shifts of deformation and flow rate with respect to the imposed pressure are analysed. We predict that the phase shifts vary throughout the oscillation; while the deformation always lags the imposed pressure, the flow rate may either lead or lag depending on the parameter values. As such, the flow rate shows hysteresis behaviour that traces either a clockwise or counterclockwise curve, or a mix of both, in the pressure–flow rate space. This directional change in hysteresis is fully characterised here in the appropriate parameter space. Furthermore, the hysteresis direction is shown to be predicted by the signs of the flow rate phase shifts at the crest and trough of the oscillation. A distinct change in the tube dynamics is also observed at high solid viscosity which leads to global or ‘whole-tube’ motion that is absent in purely elastic tubes. 

   more » « less