skip to main content


Title: Photonic independent component analysis using an on-chip microring weight bank

Independent component analysis (ICA) is a general-purpose technique for analyzing multi-dimensional data to reveal the underlying hidden factors that are maximally independent from each other. We report the first photonic ICA on mixtures of unknown signals by employing an on-chip microring (MRR) weight bank. The MRR weight bank performs so-called weighted addition (i.e., multiply-accumulate) operations on the received mixtures, and outputs a single reduced-dimensional representation of the signal of interest. We propose a novel ICA algorithm to recover independent components solely based on the statistical information of the weighted addition output, while remaining blind to not only the original sources but also the waveform information of the mixtures. We investigate both channel separability and near-far problems, and our two-channel photonic ICA experiment demonstrates our scheme holds comparable performance with the conventional software-based ICA method. Our numerical simulation validates the fidelity of the proposed approach, and studies noise effects to identify the operating regime of our method. The proposed technique could open new domains for future research in blind source separation, microwave photonics, and on-chip information processing.

 
more » « less
NSF-PAR ID:
10130712
Author(s) / Creator(s):
; ; ; ; ;
Publisher / Repository:
Optical Society of America
Date Published:
Journal Name:
Optics Express
Volume:
28
Issue:
2
ISSN:
1094-4087; OPEXFF
Page Range / eLocation ID:
Article No. 1827
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. Abstract

    The expansion of telecommunications incurs increasingly severe crosstalk and interference, and a physical layer cognitive method, called blind source separation (BSS), can effectively address these issues. BSS requires minimal prior knowledge to recover signals from their mixtures, agnostic to the carrier frequency, signal format, and channel conditions. However, previous electronic implementations did not fulfil this versatility due to the inherently narrow bandwidth of radio-frequency (RF) components, the high energy consumption of digital signal processors (DSP), and their shared weaknesses of low scalability. Here, we report a photonic BSS approach that inherits the advantages of optical devices and fully fulfils its “blindness” aspect. Using a microring weight bank integrated on a photonic chip, we demonstrate energy-efficient, wavelength-division multiplexing (WDM) scalable BSS across 19.2 GHz processing bandwidth. Our system also has a high (9-bit) resolution for signal demixing thanks to a recently developed dithering control method, resulting in higher signal-to-interference ratios (SIR) even for ill-conditioned mixtures.

     
    more » « less
  2. Microwave communications have witnessed an incipient proliferation of multi-antenna and opportunistic technologies in the wake of an ever-growing demand for spectrum resources, while facing increasingly difficult network management over widespread channel interference and heterogeneous wireless broadcasting. Radio frequency (RF) blind source separation (BSS) is a powerful technique for demixing mixtures of unknown signals with minimal assumptions, but relies on frequency dependent RF electronics and prior knowledge of the target frequency band. We propose photonic BSS with unparalleled frequency agility supported by the tremendous bandwidths of photonic channels and devices. Specifically, our approach adopts an RF photonic front-end to process RF signals at various frequency bands within the same array of integrated microring resonators, and implements a novel two-step photonic BSS pipeline to reconstruct source identities from the reduced dimensional statistics of front-end output. We verify the feasibility and robustness of our approach by performing the first proof-of-concept photonic BSS experiments on mixed-over-the-air RF signals across multiple frequency bands. The proposed technique lays the groundwork for further research in interference cancellation, radio communications, and photonic information processing.

     
    more » « less
  3. Abstract

    Radio-frequency interference is a growing concern as wireless technology advances, with potentially life-threatening consequences like interference between radar altimeters and 5 G cellular networks. Mobile transceivers mix signals with varying ratios over time, posing challenges for conventional digital signal processing (DSP) due to its high latency. These challenges will worsen as future wireless technologies adopt higher carrier frequencies and data rates. However, conventional DSPs, already on the brink of their clock frequency limit, are expected to offer only marginal speed advancements. This paper introduces a photonic processor to address dynamic interference through blind source separation (BSS). Our system-on-chip processor employs a fully integrated photonic signal pathway in the analogue domain, enabling rapid demixing of received mixtures and recovering the signal-of-interest in under 15 picoseconds. This reduction in latency surpasses electronic counterparts by more than three orders of magnitude. To complement the photonic processor, electronic peripherals based on field-programmable gate array (FPGA) assess the effectiveness of demixing and continuously update demixing weights at a rate of up to 305 Hz. This compact setup features precise dithering weight control, impedance-controlled circuit board and optical fibre packaging, suitable for handheld and mobile scenarios. We experimentally demonstrate the processor’s ability to suppress transmission errors and maintain signal-to-noise ratios in two scenarios, radar altimeters and mobile communications. This work pioneers the real-time adaptability of integrated silicon photonics, enabling online learning and weight adjustments, and showcasing practical operational applications for photonic processing.

     
    more » « less
  4. Abstract

    Blind source separation (BSS) is commonly used in functional magnetic resonance imaging (fMRI) data analysis. Recently, BSS models based on restricted Boltzmann machine (RBM), one of the building blocks of deep learning models, have been shown to improve brain network identification compared to conventional single matrix factorization models such as independent component analysis (ICA). These models, however, trained RBM on fMRI volumes, and are hence challenged by model complexity and limited training set. In this article, we propose to apply RBM to fMRI time courses instead of volumes for BSS. The proposed method not only interprets fMRI time courses explicitly to take advantages of deep learning models in latent feature learning but also substantially reduces model complexity and increases the scale of training set to improve training efficiency. Our experimental results based on Human Connectome Project (HCP) datasets demonstrated the superiority of the proposed method over ICA and the one that applied RBM to fMRI volumes in identifying task‐related components, resulted in more accurate and specific representations of task‐related activations. Moreover, our method separated out components representing intermixed effects between task events, which could reflect inherent interactions among functionally connected brain regions. Our study demonstrates the value of RBM in mining complex structures embedded in large‐scale fMRI data and its potential as a building block for deeper models in fMRI data analysis.

     
    more » « less
  5. Blind source separation (BSS) becomes popularly useful with the need for increased bandwidth utilization. However, the traditional radio-frequency (RF) electronics hardly offer the BSS the demanded frequency agility because of the inherent bandwidth limitation. The emerging integrated photonics, fortunately, can be an efficacious alternative. Here, we demonstrate a photonic BSS approach based on the microring (MRR) weightbank that achieves blind source separation of up to 13.8 GHz bandwidth. In addition, by implementing an improved MRR control method with an accuracy of up to 8.5 bits, the reduced errors give confidence in solving BSS problems with a large ill-condition number. 
    more » « less