We present a broadband integrated photonic polarization splitter and rotator (PSR) using adiabatically tapered coupled waveguides with subwavelength grating (SWG) claddings. The PSR adiabatically rotates and splits the fundamental transverse-magnetic (TM0) input to the fundamental transverse-electric (TE0) mode in the coupler waveguide, while passing the TE0input through the same waveguide. The SWGs work as an anisotropic metamaterial and facilitate modal conversions, making the PSR efficient and broadband. We rigorously present our design approaches in each section and show the SWG effect by comparing with and without the SWG claddings. The coupling coefficients in each segment explicitly show a stronger coupling effect when the SWGs are included, confirmed by the coupled-mode theory simulations. The full numerical simulation shows that the SWG-PSR operates at 1500–1750 nm (≈250 nm) wavelengths with an extinction ratio larger than 20 dB, confirmed by the experiment for the 1490–1590 nm range. The insertion losses are below 1.3 dB. Since our PSR is designed based on adiabatical mode evolution, the proposed PSR is expected to be tolerant to fabrication variations and should be broadly applicable to polarization management in photonic integrated circuits.
We design and experimentally demonstrate a polarizing beam splitter (PBS) on a silicon-on-insulator (SOI) platform based on an asymmetric directional coupler. The asymmetric directional coupler consists of a regular strip waveguide and a sub-wavelength grating (SWG) waveguide. Engineering the waveguide dispersion via SWG, the phase-matching condition can be satisfied for TM polarization over a broad bandwidth when the waveguide dimensions are optimized. The coupling region of the realized PBS is ∼7.2 µm long. For the fabricated PBS, the polarization extinction ratio (PER) is 10–45 dB and the insertion loss is 0.3–2.5 dB for TM polarization while the PER is 14–22 dB and the insertion loss is < 0.6 dB for TE polarization when operating in the wavelength range of 1460 –1610 nm.
more » « less- NSF-PAR ID:
- 10138708
- Publisher / Repository:
- Optical Society of America
- Date Published:
- Journal Name:
- OSA Continuum
- Volume:
- 3
- Issue:
- 3
- ISSN:
- 2578-7519
- Format(s):
- Medium: X Size: Article No. 560
- Size(s):
- Article No. 560
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
We propose and simulate a compact (∼29.5 µm-long) nonvolatile polarization switch based on an asymmetric Sb2Se3-clad silicon photonic waveguide. The polarization state is switched between TM0and TE0mode by modifying the phase of nonvolatile Sb2Se3between amorphous and crystalline. When the Sb2Se3is amorphous, two-mode interference happens in the polarization-rotation section resulting in efficient TE0-TM0conversion. On the other hand, when the material is in the crystalline state, there is little polarization conversion because the interference between the two hybridized modes is significantly suppressed, and both TE0and TM0modes go through the device without any change. The designed polarization switch has a high polarization extinction ratio of > 20 dB and an ultra-low excess loss of < 0.22 dB in the wavelength range of 1520-1585 nm for both TE0and TM0modes.
-
Grating coupler devices provide efficient, foundry-compatible vertical fiber-to-chip coupling solutions in integrated photonic platforms. However, standard grating coupler designs are highly polarization sensitive, which hinders their adoption. We present a new, to the best of our knowledge, type of 1D polarization-insensitive grating coupler (PIGC) that is based on a zero-birefringence subwavelength “corelet” waveguide. We demonstrate a PIGC for coupling in the telecommunications O-band in a 45-nm-node monolithic silicon-on-insulator (SOI) CMOS electronic-photonic platform, with measured insertion losses of 6.7 and 6.1 dB to transverse electric and transverse magnetic polarizations, respectively, and a ±1-dB polarization dependent loss bandwidth of 73 nm.
-
In this paper, we present the design, optimization, and implementation of a sub-wavelength grating (SWG) multi-mode interference coupler (MMI) on the silicon nitride photonic integrated circuit (PIC) platform with a significantly enhanced bandwidth compared to the conventional MMI. We extend the SWG MMI theory, previously presented for the silicon-on-insulator platform, to the Si3N4/SiO2platform. Our approach involves an initial parameter optimization for a non-paired design, followed by a shift to a paired design that offers a smaller footprint and a broader bandwidth. The optimized SWG MMI exhibits a 1 dB bandwidth of 300 nm for both the insertion loss and power imbalance, making it a significant addition to silicon nitride photonics.
-
We propose a nanogap-enhanced phase-change waveguide with silicon PIN heaters. Thanks to the enhanced light-matter interaction in the nanogap, the proposed structure exhibits strong attenuation (Δ
α = ∼35 dB/µm) and optical phase (Δn eff = ∼1.2) modulation atλ =λ3 . By exploiting a directional coupler design, we present a 1 × 2 optical switch with an insertion loss of < 4 dB and a compact coupling length of ∼ 15 µm while maintaining small crosstalk less than −7.2 dB over an optical bandwidth of 50 nm. Thermal analysis shows that a 10 V pulse of 30 ns (1×1 modulator) and 55 ns (1×2 switch) in duration is required to raise the GST temperature of the phase-change waveguide above the melting temperature to induce the amorphization; however, the complete crystallization occurs by applying a 5 V pulse of 180 ns (1×1 modulator) and a 6 V pulse of 200 ns (1×2 switch), respectively.