Twin boundary (TB) strengthening in nanotwinned metals experiences a breakdown below a critical spacing at which softening takes over. Here, we survey a range of nanotwinned materials that possess different stacking fault energies (SFEs) and understand the TB strengthening limit using atomistic simulations. Distinct from Cu and Al, the nanotwinned, ultralow SFE materials (Co, NiCoCr, and NiCoCrFeMn) intriguingly exhibit a continuous strengthening down to a twin thickness of 0.63 nm. Examining dislocation slip mode and deformation microstructure, we find the hard dislocation modes persist even when reducing the twin boundary spacing to a nanometer regime. Meanwhile, the soft dislocation mode, which causes detwinning in Cu and Al, results in phase transformation and lamellar structure formation in Co, NiCoCr, and NiCoCrFeMn. This study, providing an enhanced understanding of dislocation mechanism in nanotwinned materials, demonstrates the potential for controlling mechanical behavior and ultimate strength with broadly tunable composition and SFE, especially in multi-principal element alloys.
Nanotwinned materials have been widely studied as a promising class of nanostructured materials that exhibit an exceptional combination of high strength, good ductility, large fracture toughness, remarkable fatigue resistance, and creep stability. Recently, an apparent controversy has emerged with respect to how the strength of nanotwinned materials varies as the twin thickness is reduced. While a transition from hardening to softening was observed in nanotwinned Cu when the twin thickness is reduced below a critical value, continuous hardening was reported in nanotwinned ceramics and nanotwinned diamond. Here, by conducting atomistic simulations and developing a theoretical modeling of nanotwinned Pd and Cu systems, we discovered that there exists a softening temperature, below which the material hardens continuously as the twin thickness is reduced (as in nanotwinned ceramics and diamond), while above which the strength first increases and then decreases, exhibiting a maximum strength and a hardening to softening transition at a critical twin thickness (as in nanotwinned Cu). This important phenomenon has been attributed to a transition from source- to stress-controlled plasticity below the softening temperature, and suggests that different hardening behaviors may exist even in the same nanotwinned material depending on the temperature and that at a given temperature, different materials could exhibit different hardening behaviors depending on their softening temperature.
more » « less- Award ID(s):
- 1709318
- PAR ID:
- 10153911
- Publisher / Repository:
- Nature Publishing Group
- Date Published:
- Journal Name:
- npj Computational Materials
- Volume:
- 5
- Issue:
- 1
- ISSN:
- 2057-3960
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
-
The nanoscopic deformation of ⟨111⟩ nanotwinned copper nanopillars under strain rates between 10^−5/s and 5×10^−4/s was studied by using in situ transmission electron microscopy. The correlation among dislocation activity, twin boundary instability due to incoherent twin boundary migration and corresponding mechanical responses was investigated. Dislocations piled up in the nanotwinned copper, giving rise to significant hardening at relatively high strain rates of 3–5×10^−4/s. Lower strain rates resulted in detwinning and reduced hardening, while corresponding deformation mechanisms are proposed based on experimental results. At low/ultralow strain rates below 6×10^−5/s, dislocation activity almost ceased operating, but the migration of twin boundaries via the 1/4 ⟨10-1⟩ kink-like motion of atoms is suggested as the detwinning mechanism. At medium strain rates of 1–2×10^−4/s, detwinning was decelerated likely due to the interfered kink-like motion of atoms by activated partial dislocations, while dislocation climb may alternatively dominate detwinning. These results indicate that, even for the same nanoscale twin boundary spacing, different nanomechanical deformation mechanisms can operate at different strain rates.more » « less
-
The friction and wear behavior of materials are not intrinsic properties, but extrinsic properties; in other words, they can drastically vary depending on test and environmental conditions. In ambient air, humidity is one such extrinsic parameter. This paper reviews the effects of humidity on macro- and nano-scale friction and wear of various types of materials. The materials included in this review are graphite and graphene, diamond-like carbon (DLC) films, ultrananocrystalline diamond (UNCD), transition metal dichalcogenides (TMDs), hexagonal boron nitride (h-BN), boric acid, silicon, silicon oxide, silicates, advanced ceramics, and metals. Details of underlying mechanisms governing friction and wear behaviors vary depending on materials and humidity; nonetheless, a comparison of various material cases revealed an overarching trend. Tribochemical reactions between the tribo-materials and the adsorbed water molecules play significant roles; such reactions can occur at defect sites in the case of two-dimensionally layered materials and carbon-based materials, or even on low energy surfaces in the case of metals and oxide materials. It is extremely important to consider the effects of adsorbed water layer thickness and structure for a full understanding of tribological properties of materials in ambient air.more » « less
-
As various property studies continue to emerge on high entropy and entropy-stabilized ceramics, we seek a further understanding of the property changes across the phase boundary between “high-entropy” and “entropy-stabilized” phases. The thermal and mechanical properties of bulk ceramic entropy stabilized oxide composition Mg 0.2 Co 0.2 Ni 0.2 Cu 0.2 Zn 0.2 O are investigated across this critical transition temperature via the transient plane-source method, temperature-dependent x-ray diffraction, and nano-indentation. The thermal conductivity remains constant within uncertainty across the multi-to-single phase transition at a value of ≈2.5 W/mK, while the linear coefficient of thermal expansion increases nearly 24% from 10.8 to 14.1 × 10 −6 K −1 . Mechanical softening is also observed across the transition.more » « less
-
more » « less
Conventional rolling is a plastic deformation process that uses compression between two rolls to reduce material thickness and produce sheet/plane geometries. This deformation process modifies the material structure by generating texture, reducing the grain size, and strengthening the material. The rolling process can enhance the strength and hardness of lightweight materials while still preserving their inherent lightness. Lightweight metals like magnesium alloys tend to lack mechanical strength and hardness in load-bearing applications. The general rolling process is controlled by the thickness reduction, velocity of the rolls, and temperature. When held at a constant thickness reduction, each pass through the rolls introduces an increase in strain hardening, which could ultimately result in cracking, spallation, and other defects. This study is designed to optimize the rolling process by evaluating the effects of the strain rate, rather than the thickness reduction, as a process control parameter.
