An official website of the United States government
Additive manufacturing has been used to develop a variety of scaffold designs for clinical and industrial applications. Mechanical properties (i.e., compression, tension, bending, and torsion response) of these scaffolds are significantly important for load-bearing orthopaedic implants. In this study, we designed and additively manufactured porous metallic biomaterials based on two different types of triply periodic minimal surface structures (i.e., gyroid and diamond) that mimic the mechanical properties of bone, such as porosity, stiffness, and strength. Physical and mechanical properties, including compressive, tensile, bending, and torsional stiffness and strength of the developed scaffolds, were then characterised experimentally and numerically using finite element method. Sheet thickness was constant at 300 μm, and the unit cell size was varied to generate different pore sizes and porosities. Gyroid scaffolds had a pore size in the range of 600–1200 μm and a porosity in the range of 54–72%, respectively. Corresponding values for the diamond were 900–1500 μm and 56–70%. Both structure types were validated experimentally, and a wide range of mechanical properties (including stiffness and yield strength) were predicted using the finite element method. The stiffness and strength of both structures are comparable to that of cortical bone, hence reducing the risks of scaffold failure. The results demonstrate that the developed scaffolds mimic the physical and mechanical properties of cortical bone and can be suitable for bone replacement and orthopaedic implants. However, an optimal design should be chosen based on specific performance requirements.
more »
« less
Structure and Deformation of Gradient Metal Foams Produced by Machining
The effects of surface structure on mechanical performance for open-cell aluminum foam specimens were investigated in the present study. A surface gradient for pore structure and diameter was introduced into open-cell aluminum foams by machining-based processing. The structure changes in the strut and pore network were evaluated by computed tomography characterization. The role of structure gradients in affecting mechanical performance was determined using digital volume correlation and in situ compression within the computed tomographic scanner. These preliminary results show that the strength of these materials may be enhanced through surface structural gradients.
more »
« less
- Award ID(s):
- 1825640
- PAR ID:
- 10157779
- Date Published:
- Journal Name:
- Journal of Manufacturing Science and Engineering
- Volume:
- 141
- Issue:
- 7
- ISSN:
- 1087-1357
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Andrew Yeh-Ching Nee, editor-ion-chief (Ed.)Wire arc additive manufacturing (WAAM) has received increasing use in 3D printing because of its high deposition rates suitable for components with large and complex geometries. However, the lower forming accuracy of WAAM than other metal additive manufacturing methods has imposed limitations on manufacturing components with high precision. To resolve this issue, we herein implemented the hybrid manufacturing (HM) technique, which integrated WAAM and subtractive manufacturing (via a milling process), to attain high forming accuracy while taking advantage of both WAAM and the milling process. We describe in this paper the design of a robot-based HM platform in which the WAAM and CNC milling are integrated using two robotic arms: one for WAAM and the other for milling immediately following WAAM. The HM was demonstrated with a thin-walled aluminum 5356 component, which was inspected by X-ray micro-computed tomography (μCT) for porosity visualization. The temperature and cutting forces in the component under milling were acquired for analysis. The surface roughness of the aluminum component was measured to assess the surface quality. In addition, tensile specimens were cut from the components using wire electrical discharge machining (WEDM) for mechanical testing. Both machining quality and mechanical properties were found satisfactory; thus the robot-based HM platform was shown to be suitable for manufacturing high-quality aluminum parts.more » « less
-
Abstract In this paper, an open-cell metallic foam was filled in by a tough shape memory polymer (SMP), to form a hybrid metal/polymer composite with multifunctionalities and enhanced mechanical properties. This work aims to study the positive composite actions between the metallic skeleton and the SMP filler. Mechanical, thermal, and conductive properties of the resulting hybrid composite were evaluated and compared to the individual components. Uniaxial compression tests and shape memory effect tests were conducted. Results demonstrated an improvement in the compressive strength and toughness. The hybrid composite also exhibited excellent shape recovery and high recovery stress of 1.76 MPa. Infrared thermography has been used to verify the free shape recovery by Joule heating. Sandwich structures with the hybrid composite as the core were studied through low velocity impact test and three-point bending test. The sandwich structures with the composite foam core showed significant performance improvement in both tests. Electrical resistivity study during the three-point bending test validates the possible application of this multifunctional polymer-aluminum open cell foam composite as strain sensor. This type of hybrid composites can be beneficial in many industrial sectors that search for an ideal combination of high strength, high toughness, low weight, damage sensing, and excellent energy absorption capabilities.more » « less
-
Friction surfacing technique is a thermo-mechanical approach for metallic deposition, suitable for a broad range of materials and applications. Friction surfacing can be employed for various industrial purposes such as coating, welding, repairing defective parts, surface hardening, and improving corrosion performance. In this technique, frictional heat generated at the interface of the consumable tool and substrate results in a severe plastic deformation at the end of the rod, enabling the deposition of a consumable material on the substrate surface. In this investigation, a novel method in friction surfacing, lateral friction surfacing, is employed to deposit the aluminum coatings. In this novel approach, the side of the consumable tool is pressed against the surface of the substrate, and the material transfer happens from the lateral surface of the tool. This technique provides extremely thin and smooth deposits, which are more consistent compared to the conventional approach of friction surfacing. Moreover, this technique enables fabricating of deposits in lower temperatures, lessening the thermal impacts on the microstructures and mechanical properties of the deposits. In this investigation plates of 1018 mild steel were partially coated with various aluminum alloys and corroded in an accelerated corrosion test chamber. The corrosion performance of the partially coated sample was evaluated by mass loss measurement. It was found that AA5086 offered the most corrosion protection. After 13 cycles of GM9540P test, equivalent to approximately 3½ years exposure at a mild/moderate marine site in Hawaii, almost all of the deposited aluminum was consumed.more » « less
-
6061 aluminum composites with 0.5 and 1 vol. % graphene nanoplatelets as well as 1 and 2 vol. % activated nanocarbon were manufactured by a powder metallurgy method. Scanning electron microscopy and Raman spectroscopy were used to study the morphology, structure, and distribution of nanocarbon reinforcements in the composite samples. Density Functional Theory (DFT) calculations were performed to understand the aluminum-carbon bonding and the effects of hybridized networks of carbon atoms on nanocarbon aluminum matrix composites. Scanning electron microscopy showed the good distribution and low agglomeration tendencies of nanoparticles in the composites. The formation of secondary phases at the materials interface was not detected in the hot-pressed composites. Raman spectroscopy showed structural changes in the reinforced composites after the manufacturing process. The results from Density Functional Theory calculations suggest that it is thermodynamically possible to form carbon rings in the aluminum matrix, which may be responsible for the improved mechanical strength. Our results also suggest that these carbon networks are graphene-like, which also agrees with the Raman spectroscopy data. Micro-Vickers hardness and compressive tests were used to determine the mechanical properties of the samples. Composites presented enhanced hardness, yield and ultimate strength compared to the 6061 aluminum alloy with no nanocarbon reinforcement. Ductility was also affected, as shown by the reduction in elongation and by the number of dimples in the fractured surfaces of the materials.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1115/1.4043768
