More Like this

1. Synthesis of 1,6‐ didecylnaphtho [1,2‐ b :5,6‐ b '] difuran‐based copolymers by direct heteroarylation polymerization

   https://doi.org/10.1002/pol.20200069  

   Muller, Evan W. ; Burney‐Allen, Alfred A. ; Shaw, Jessica ; Wheeler, David L. ; Duzhko, Volodimyr ; Jeffries‐EL, Malika ( March 2020 , Journal of Polymer Science)

   The use of direct CH arylation cross‐coupling polymerization was evaluated for the synthesis of donor–acceptor conjugated co‐polymers using the novel donor 1,6‐didecylnaphtho[1,2‐b:5,6‐b']difuran and either thieno[3,4‐c]pyrrole‐4,6‐dione (TPD) or 1,4‐diketopyrrolo[3,4‐c]pyrrole (DPP) as the acceptor. Thiophene and furan moieties were used to flank the DPP group and the impact of these heterocycles on the polymers' properties was evaluated. The alkyl chains on the diketopyrrolopyrrole monomers were varied to engineer the solubility and morphology of the materials. All of the polymers have similar optoelectronic properties with narrow optical band gaps around 1.3 eV, which is ideal for solar energy harvesting. Unfortunately, these polymers also had high‐lying highest occupied molecular orbital levels of −4.8 to −5.1, and as a result bulk‐heterojunction photovoltaic cells fabricated using the soluble fullerene derivative PC₇₁BM as the electron‐acceptor and these polymers as donor materials exhibited poor performance due to limited V_ocvalues. An examination of the films from these blends indicates that film‐thickness and morphology were also a major hindrance to performance and a potential point of improvement for future materials.

    

   more » « less
2. Hybrid Cathodic/Anodic Electrosynthesis of Phase Pure Ag 4 V 2 O 7 Thin Films

   https://doi.org/10.1149/1945-7111/acd149  

   Vali, Abbas ; Kim, Soo Yeon ; Danladi, Fahad ; Rawat, Abhishek ; Zhang, Chuzhong ; Toth, Peter S. ; Janáky, Csaba ; Myung, Noseung ; Meletis, Efstathios I. ; Rajeshwar, Krishnan ( May 2023 , Journal of The Electrochemical Society)

   Here, we demonstrate a two-step electrosynthesis approach for the preparation of silver pyrovanadate, Ag 4 V 2 O 7 in thin-film form. In the first, cathodic step, polycrystalline Ag was deposited on fluorine doped tin oxide (FTO) substrate from a non-aqueous bath. Aqueous pyrovanadate species were then generated by aging of a CO 2 -infused sodium orthovanadate (Na 3 VO 4 ) solution for three weeks. Silver ions were subsequently generated in situ in this medium using anodic stripping of the Ag/ITO films from the first step. Interfacial precipitation of the Ag + ions with the pyrovanadate species afforded the targeted product in phase pure form. The various stages of the electrosynthesis were monitored in situ via the combined use of voltammetry, electrochemical quartz crystal nanogravimetry (EQCN), and coulometry. The Ag 4 V 2 O 7 thin films were characterized by a variety of experimental techniques, including X-ray diffraction, laser Raman spectroscopy, diffuse reflectance spectroscopy, scanning electron microscopy, and high-resolution transmission electron microscopy. Surface photovoltage spectroscopy, ambient-pressure photoemission spectroscopy, and Kelvin probe contact potential difference (work function) measurements afforded information on the energy band structure of the p -type Ag 4 V 2 O 7 semiconductor. Finally, the electrochemical and photoelectrochemical properties of the electrosynthesized Ag 4 V 2 O 7 thin films were studied in both aqueous and non-aqueous electrolytes. 

   more » « less
3. Layer-by-Layer Deposition of Rh(I) Diisocyanide Coordination Polymers on Au(111) and Their Chemical and Electrochemical Stability

   https://doi.org/10.1021/acs.jpcc.2c05079  

   Lee, Gwendolynne L. ; Chan, Thomas ; Palasz, Joseph M. ; Kubiak, Clifford P. ( September 2022 , The Journal of Physical Chemistry C)

   The synthesis of electrode-attached Rh(I) diisocyanide coordination polymers that incorporate a series of arylene diisocyanide linkers and which are grown from gold surfaces by a bottom-up, layer-by-layer procedure that allows for a high level of control for the film thickness is reported. A seed layer of the arylene diisocyanide ligand is used to template directional growth of the coordination polymer made using the well-studied square-planar rhodium tetrakis(isocyanide) as the metal node. Materials ranging from 1 to 30 layers were prepared via layer-by-layer solution-phase deposition. Characterization of the polymer films using scanning electron microscopy and ellipsometry shows layer-by-layer control in these films with linear thickness growth per layer. Phasemodulated infrared reflection absorption spectroscopy (PM-IRRAS), diffuse reflectance UV−vis, and X-ray photoelectron spectroscopy (XPS) were used to confirm the structures of the films. Although prior reports of related coordination polymers and films based on diisocyanides showed considerable air-instability, the films reported here demonstrate significantly improved chemical stability and electrochemical stability at a moderately high applied bias. Electrochemical characterization and ex situ XPS demonstrate that these diisocyanide films are stable to stripping at potentials up to −2.2 V versus decamethylferrocene in acetonitrile, supporting their relevance for electrochemical applications. 

   more » « less
4. Trap-dominated nitrogen dioxide and ammonia responses of air-stable p-channel conjugated polymers from detailed bias stress analysis

   https://doi.org/10.1039/D0TC05458E  

   Mukhopadhyaya, Tushita ; Katz, Howard E. ( March 2021 , Journal of Materials Chemistry C)

   null (Ed.)

   The improvement of conjugated polymer-based gas sensors involves fine tuning the backbone electronic structure and solid-state microstructure to combine high stability and sensitivity. We had previously developed a series of diketopyrrolopyrrole (DPP)-based polymer semiconductors by introducing a variety of fluorene linkers to study the trends and mechanisms governing gas sensitivities and electronic stability in air and under gate and drain bias stress. The proportional on-current change of organic field-effect transistors (OFETs) using a dithienyl DPP–fluorene polymer reached ∼600% for a sequential exposure from 0.5–20 ppm of NO 2 for 5 minutes and also a high response-to-drift ratio under dynamic bias stress. In the present work we specify the roles of static bias stress and traps in the sensing process for the first time. Apart from electronic structure, defects at the molecular and microstructural levels govern the ability to form and sustain traps and subsequent backbone dopability. A polymer with a twisted backbone was observed to be capable of creating an energetically broad trap distribution while a polymer with a high degree of solid-state order shows a tendency to form an energetically narrow trap distribution and a fast passivation of traps on exposure to air. The stability and energetic distribution of traps on subjecting the polymers to bias stress was related to electronic structure and solid-state packing; and the ability of NO 2 and NH 3 to fill/create traps further was evaluated. At a bias stress condition of V G = V D = −80 V, the polymers retain their NO 2 sensitivity both post NO 2 -aided recovery and air-aided recovery. In order to verify the ability of NH 3 to create traps, traps were erased from the OFET sensors by charging with the aid of a positive gate voltage leading to an increase in the NH 3 response when compared to air controls. This work demonstrates that the charge-trap filling and generation response mechanism is predominant and can even be leveraged for higher responses to vapors. Backbone dopability appears to be a minor contributor to responses in this category of polymeric semiconductors with engineered defects. Finally, bias stress generally does not preclude this category of OFET vapor sensors from recovering their original sensitivities. 

   more » « less
5. Electrocatalytic Conversion of Furanic Compounds for Production of Valuable Chemicals

   Li, Wenzhen ; Chadderdon, Xiaotong ; Chadderdon, David ; Liu, Hengzhou ( August 2021 , 72nd International Society of Electrochemistry Meeting)

   Biomass is abundant, inexpensive and renewable, therefore, it is highly expected to play a significant role in our future energy and chemical landscapes. The US DOE has identified furanic compounds (furfural and 5-(hydroxymethyl)furfural (HMF)) as the top platform building-block chemicals that can be readily derived from biomass sources [1]. Electrocatalytic conversion of these furanic compounds is an emerging route for the sustainable production of valuable chemicals [2, 3]. In my presentation, I will first present our recent mechanistic study of electrochemical reduction of furfural through a combination of voltammetry, preparative electrolysis, thiol-electrode modifications, and kinetic isotope studies [4]. It is demonstrated that two distinct mechanisms are operable on metallic Cu electrodes in acidic electrolytes: (i) electrocatalytic hydrogenation (ECH) and (ii) direct electroreduction. The contributions of each mechanism to the observed product distribution are clarified by evaluating the requirement for direct chemical interactions with the electrode surface and the role of adsorbed hydrogen. Further analysis reveals that hydrogenation and hydrogenolysis products are generated by parallel ECH pathways. Understanding the underlying mechanisms enables the manipulation of furfural reduction by rationally tuning the electrode potential, electrolyte pH, and furfural concentration to promote selective formation of important bio-based polymer precursors and fuels. Next, I will present electrocatalytic conversion of HMF to two biobased monomers in an H-type electrochemical cell [5]. HMF reduction (hydrogenation) to 2,5-bis(hydroxymethyl)furan (BHMF) was achieved under mild electrolyte conditions and ambient temperature using a Ag/C cathode. Meanwhile, HMF oxidation to 2,5-furandicarboxylic acid (FDCA) with ~100% efficiency was facilitated under the same conditions by a homogeneous nitroxyl radical redox mediator, together with an inexpensive carbon felt anode. The selectivity and efficiency for Ag-catalyzed BHMF formation were sensitive to cathode potential, owing to competition from HMF hydrodimerization reactions and water reduction (hydrogen evolution). Moreover, the carbon support of Ag/C was active for HMF reduction and contributed to undesired dimer/oligomer formation at strongly cathodic potentials. As a result, high BHMF selectivity and efficiency were only achieved within a narrow potential range near –1.3 V. Fortunately, the selectivity of redox-mediated HMF oxidation was insensitive to anode potential, thus allowing HMF hydrogenation and oxidation half reactions to be performed together in a single cathode-potential-controlled cell. Electrocatalytic HMF conversion in a paired cell achieved high molar yields of BHMF and FDCA, and nearly doubled electron efficiency compared to the unpaired cell. Finally, I will briefly introduce our recent work on the development of a three-electrode flow cell with an oxide-derived Ag (OD-Ag) cathode and catbon felt anode for paring elecatalytic oxidation and reduction of HMF. The flow cell has a remarkable cell voltage reduction from ~7.5 V to ~2.0 V by transferring the electrolysis from the H-type cell to the flow cell [6]. This represents a more than fourfold increase in the energy efficiency at the 10 mA operation. A combined faradaic efficiency of 163% was obtained to BHMF and FDCA. Alternatively, the anodic hydrogen oxidation reaction on platinum further reduced the cell voltage to only ~0.85 V at 10 mA operation. These paired processes have shown potential for integrating renewable electricity and carbon for distributed chemical manufacturing in the future. 

   more » « less