skip to main content


Title: Distributed-feedback blue laser diode utilizing a tunnel junction grown by plasma-assisted molecular beam epitaxy

In this paper, we demonstrate a novel approach utilizing tunnel junction (TJ) to realize GaN-based distributed feedback (DFB) laser diodes (LDs). Thanks to the use of the TJ the top metal contact is moved to the side of the ridge and the DFB grating is placed directly on top of the ridge. The high refractive index contrast between air and GaN, together with the high overlap of optical mode with the grating, provides a high coupling coefficient. The demonstrated DFB LD operates at λ=450.15 nm with a side mode suppression ratio higher than 35dB. The results are compared to a standard Fabry-Perot LD.

 
more » « less
NSF-PAR ID:
10201070
Author(s) / Creator(s):
; ; ; ; ; ; ; ; ; ;
Publisher / Repository:
Optical Society of America
Date Published:
Journal Name:
Optics Express
Volume:
28
Issue:
23
ISSN:
1094-4087; OPEXFF
Page Range / eLocation ID:
Article No. 35321
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. Recently, the use of bottom-TJ geometry in LEDs, which achieves N-polar-like alignment of polarization fields in conventional metal-polar orientations, has enabled enhancements in LED performance due to improved injection efficiency. Here, we elucidate the root causes behind the enhanced injection efficiency by employing mature laser diode structures with optimized heterojunction GaN/In0.17Ga0.83N/GaN TJs and UID GaN spacers to separate the optical mode from the heavily doped absorbing p-cladding regions. In such laser structures, polarization offsets at the electron blocking layer, spacer, and quantum barrier interfaces play discernable roles in carrier transport. By comparing a top-TJ structure to a bottom-TJ structure, and correlating features in the electroluminescence, capacitance-voltage, and current-voltage characteristics to unique signatures of the N- and Ga-polar polarization heterointerfaces in energy band diagram simulations, we identify that improved hole injection at low currents, and improved electron blocking at high currents, leads to higher injection efficiency and higher output power for the bottom-TJ device throughout 5 orders of current density (0.015–1000 A/cm2). Moreover, even with the addition of a UID GaN spacer, differential resistances are state-of-the-art, below 7 × 10−4Ωcm2. These results highlight the virtues of the bottom-TJ geometry for use in high-efficiency laser diodes.

     
    more » « less
  2. Interband cascade lasers (ICLs) are efficient and compact mid-infrared (3-5 µm) light sources with many applications. By enhancing the coupling coefficient and using a type-I ICL wafer, single-mode ICLs were demonstrated based on V-coupled cavity with significantly extended tuning range and with a side mode suppression ratio (SMSR) exceeding 35 dB in continuous wave operation near 3 µm. A V-coupled cavity ICL exhibited a wavelength tuning up to 67 nm at a fixed temperature, and the total tuning range exceeds 210 nm when the heat sink temperature is adjusted from 80 to 180 K. The realization of single-mode in such a wide temperature range with a tuning range exceeding 210 nm verified the advantage of V-coupled cavity ICLs for effective detection of multiple gas species. This is very different from the conventional distributed feedback (DFB) laser where the single-mode operation is restricted to a narrow temperature range, in which the match between the gain peak and the DFB grating period determined wavelength is required. Another V-coupled cavity ICL is tuned over 120 nm from 2997.56 nm to 3117.50 nm with the heat-sink temperature varied from 210 K to 240 K, over 100 K higher than the previously reported maximum operating temperature for V-coupled cavity ICLs.

     
    more » « less
  3. Tunnel junctions (TJs) have recently been proposed as a solution for several III-nitride current problems and to enhance new structures. Reported III-nitride TJs grown by metalorganic chemical vapor deposition (MOCVD) resulted in backward diodes with rectifying behavior in forward bias, even with Mg and Si doping in 10 20  cm −3 . This behavior limits applications in several device structures. We report a TJ structure based on p + In 0.15 Ga 0.85 N/n + In 0.05 Ga 0.95 N, where the n-side of the junction is co-doped with Si and Mg and with electron and hole concentrations in the mid-10 19  cm −3 for both the n and p dopants. Co-doping creates deep levels within the bandgap that enhances tunneling under forward biased conditions. The TJ structure was investigated on both GaN substrates and InGaN templates to study the impact of strain on the TJ I–V characteristics. The resulting TJ I–V and resistivities reported indicate the potential for this TJ approach in several device structures based on III-nitrides. We are not aware of any previous MOCVD grown TJs that show Ohmic performance in both forward and reverse biases. 
    more » « less
  4. Abstract

    Plasmonic grating filters can be fabricated in single lithography process and reduce the cost of colour filters used in hyperspectral cameras. Due to the presence of Rayleigh Anomaly (RA) peak, however, it has not been possible to design filter array spanning wide-spectral-range without sacrificing spectral purity. In this paper, a plasmonic grating filter design using Metal-Insulator-Metal (MIM) with suppressed RA peak is presented. Proposed filter allows extending spectral range without sacrificing spectral purity. Using proposed MIM structure, surface plasmon polariton (SPP) mode supported on air side of bottom grating structure is cancelled by second set of SPP mode on top grating structure. This allows designing filter array with improved spectral range and achieves better than 2× improvement in suppression of the Rayleigh Anomaly peak.

     
    more » « less
  5.  
    more » « less