skip to main content

Attention:

The NSF Public Access Repository (PAR) system and access will be unavailable from 11:00 PM ET on Thursday, February 13 until 2:00 AM ET on Friday, February 14 due to maintenance. We apologize for the inconvenience.


Title: Kinetic Monte Carlo Simulation of Perovskite Solar Cells to Probe Film Coverage and Thickness
  more » « less
PAR ID:
10216306
Author(s) / Creator(s):
 ;  ;  ;  ;  ;  ;  ;  ;  ;  ;  
Publisher / Repository:
Wiley Blackwell (John Wiley & Sons)
Date Published:
Journal Name:
Advanced Energy and Sustainability Research
Volume:
2
Issue:
3
ISSN:
2699-9412
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. Abstract

    In its initial phase in 2009, the inorganic‐organic hybrid perovskite solar cells (PSCs) delivered a 3.8% power conversion efficiency (PCE), which is far below the present 25.7% PCE obtained in 2022. The significant improvement of the efficiency of PSCs in such a short period has stimulated significant interest in the photovoltaic community. However, the performance of current PSCs is behind the commercially available and widely used solar cells in terms of stability and scalability. Among various commonly studied perovskite materials, methylammonium lead iodide (MAPbI3) is the most widely studied. This review will focus on the common solar cell structures (mesoporous, inverted planar p‐i‐n, planar n‐i‐p) using MAPbI3perovskite as an active layer and the effect of these solar cell structures on their performances. Furthermore, some commonly‐used strategies are outlined for improving the device performance, such as optimizing the deposition technique of the charge transporting and the active layers, modifying the properties of the carrier transporting layer and the perovskite layer by interface engineering and doping, optimizing the perovskite surface morphology, along with others. This article will also discuss the hole transport free and electron transport free MAPbI3PSCs.

     
    more » « less
  2.  
    more » « less
  3. Abstract

    Poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) is a popular hole transport material in perovskite solar cells (PSCs). However, the devices with PEDOT:PSS exhibit large open‐circuit voltage (Voc) loss and low efficiency, which is attributed to mismatched energy level alignment and the poor interface of PEDOT:PSS and perovskite. Here, three polymer analogues to polyaniline (PANI), PANI–carbazole (P1), PANI–phenoxazine (P2), and PANI–phenothiazine (P3) are designed with different energy levels to modify the interface between PEDOT:PSS and the perovskite layer and improve the device performance. The effects of the polymers on the device performance are demonstrated by evaluating the work function adjustment, perovskite growth control, and interface modification in MAPbI3‐based PSCs. Low bandgap Sn–Pb‐based PSCs are also fabricated to confirm the effects of the polymers. Three effects are evaluated through the comparison study of PEDOT:PSS‐based organic solar cells and MAPbI3 PSCs based on the PEDOT:PSS modified by P1, P2, and P3. The order of contribution for the three effects is work function adjustment > surface modification > perovskite growth control. MAPbI3 PSCs modified with P2 exhibit a highVocof 1.13 V and a high‐power conversion efficiency of 21.06%. This work provides the fundamental understanding of the interface passivation effects for PEDOT:PSS‐based optoelectronic devices.

     
    more » « less
  4. Abstract

    Flexible perovskite solar cells (f‐PSCs) have attracted great attention due to their promising commercial prospects. However, the performance off‐PSCs is generally worse than that of their rigid counterparts. Herein, it is found that the unsatisfactory performance of planar heterojunction (PHJ)f‐PSCs can be attributed to the undesirable morphology of electron transport layer (ETL), which results from the rough surface of the flexible substrate. Precise control over the thickness and morphology of ETL tin dioxide (SnO2) not only reduces the reflectance of the indium tin oxide (ITO) on polyethylene 2,6‐naphthalate (PEN) substrate and enhances photon collection, but also decreases the trap‐state densities of perovskite films and the charge transfer resistance, leading to a great enhancement of device performance. Consequently, thef‐PSCs, with a structure of PEN/ITO/SnO2/perovskite/Spiro‐OMeTAD/Ag, exhibit a power conversion efficiency (PCE) up to 19.51% and a steady output of 19.01%. Furthermore, thef‐PSCs show a robust bending resistance and maintain about 95% of initial PCE after 6000 bending cycles at a bending radius of 8 mm, and they present an outstanding long‐term stability and retain about 90% of the initial performance after >1000 h storage in air (10% relative humidity) without encapsulation.

     
    more » « less
  5. Conjugated molecules have been typically utilized as either hole or electron extraction layers to boost the device performance of perovskite solar cells (PSCs), formed from three-dimensional (3D) perovskites, due to their high charge carrier mobility and electrical conductivity. However, the passivating role of conjugated molecules in creating two-dimensional (2D) perovskites has rarely been reported. In this study, we report novel conjugated aniline 3-phenyl-2-propen-1-amine (PPA) based 2D perovskites and further demonstrate efficient and stable PSCs containing a (PPA) x (MAPbI 3 ) 1− x /MAPbI 3 bilayer thin film (where MA is CH 3 NH 3 + ). The (PPA) x (MAPbI 3 ) 1− x /MAPbI 3 bilayer thin film possesses superior crystallinity and passivated trap states, resulting in enhanced charge transport and suppressed charge carrier recombination compared to those of a 3D MAPbI 3 thin film. As a result, PSCs containing the (PPA) x (MAPbI 3 ) 1− x /MAPbI 3 bilayer thin film exhibit a power conversion efficiency (PCE) of 21.98%, which is approximately a 25% enhancement compared to that of the MAPbI 3 thin film. Moreover, un-encapsulated PSCs containing the (PPA) x (MAPbI 3 ) 1− x /MAPbI 3 bilayer thin film retain 50% of their initial PCE after 1200 hours in an ambient atmosphere (25 °C, and 30 ± 10 humidity), whereas PSCs with the 3D MAPbI 3 thin film show significant degradation after 100 hours and a degradation of more than 50% of their original PCE after 500 hours. These results demonstrate that the incorporation of conjugated molecules as organic spacer cations to create 2D perovskites on top of 3D perovskites is an effective way to approach high-performance PSCs. 
    more » « less