skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Elastic Modulus, Hardness, and Fracture Toughness of Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 Solid Electrolyte
Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 (LLZTO) is a promising inorganic solid electrolyte due to its high Li + conductivity and electrochemical stability for all-solid-state batteries. Mechanical characterization of LLZTO is limited by the synthesis of the condensed phase. Here we systematically measure the elastic modules, hardness, and fracture toughness of LLZTO polycrystalline pellets of different densities using the customized environmental nanoindentation. The LLZTO samples are sintered using the hot-pressing method with different amounts of Li 2 CO 3 additives, resulting in the relative density of the pellets varying from 83% to 98% and the largest grain size of 13.21 ± 5.22 μm. The mechanical properties show a monotonic increase as the sintered sample densifies, elastic modulus and hardness reach 158.47 ± 10.10 GPa and 11.27 ± 1.38 GPa, respectively, for LLZTO of 98% density. Similarly, fracture toughness increases from 0.44 to 1.51 MPa⋅m 1/2 , showing a transition from the intergranular to transgranular fracture behavior as the pellet density increases. The ionic conductivity reaches 4.54 × 10 −4 S/cm in the condensed LLZTO which enables a stable Li plating/stripping in a symmetric solid-state cell for over 100 cycles. This study puts forward a quantitative study of the mechanical behavior of LLZTO of different microstructures that is relevant to the mechanical stability and electrochemical performance of all-solid-state batteries.  more » « less
Award ID(s):
1832707
PAR ID:
10352322
Author(s) / Creator(s):
; ; ; ; ;
Date Published:
Journal Name:
Chinese Physics Letters
Volume:
38
Issue:
9
ISSN:
0256-307X
Page Range / eLocation ID:
098401
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; (, Solid State Ionics)
    Garnet type LLZTO ceramic oxide is a promising solid-state electrolyte for use in Li-ion batteries because it has good chemical stability, adequate mechanical strength. However, lithium dendrite growth still needs to be addressed. The opacity of the solid electrolyte hinders in-situ investigation of dendrite growth. Therefore, semi-transparent LLZTO with high-density is needed. The traditional fabrication process for the garnet type LLZTO is cumbersome, and dense LLZTO disks with high transparency are difficult to fabricate. In this work, Al-LLZTO powder was made by solid-state reaction. A wet ceramic processing method, pressure filtration followed by sintering, was developed to make dense LLZTO with high ionic conductivity (1.47×10-4 S/cm) and adequate transmittance (17–23%) to visible light from 500 to 800 nm to observe and monitor dendrite growth. 
    more » « less
  2. ; ; (, Advanced Energy and Sustainability Research)
    Tantalum‐doped lithium lanthanum zirconate garnet (Li7−xLa3Zr2−xTaxO12[LLZTO]) has received interest as a solid electrolyte for solid‐state lithium batteries due to its good electrochemical properties and ionic conductivity. However, the source of discrepancies for reported values of ionic conductivity in nominally or nearly equivalent compositions of LLZTO is not completely clear. Herein, synthesis‐related factors that may contribute to the differences in performance of garnet electrolytes are systematically characterized. The conductivity of samples with composition Li6.4La3Zr1.4Ta0.6O12prepared by various methods including solid‐state reaction (SSR), combustion, and molten salt synthesis is compared. Varying levels of elemental inhomogeneity, comprising a variation in Ta and Zr content on the level of individual LLZTO particles, are identified. The elemental inhomogeneity is found to be largely preserved even after high‐temperature sintering and correlated with reduced ionic conductivity. It is shown that the various synthesis and processing‐related variables in each of the preparation methods play a role in these compositional variations, and that even LLZTO synthesized via conventional, high‐temperature SSR can exhibit substantial variability in local composition. However, by improving reagent mixing and using LLZTO powder with low agglomeration and small particle size distribution, the compositional uniformity, and hence, ionic conductivity, of sintered garnet electrolytes can be improved. 
    more » « less
  3. ; ; ; ; ; ; ; ; (, Advanced Energy Materials)
    Abstract Solid state lithium metal batteries using garnet solid electrolytes such as LLZTO (Li6.4La3Zr1.5Ta0.5O12) promise substantial improvements in energy density and safety. However, practical implementation is hindered by lithium dendrite penetration at high current densities. Recent work shows that internal electrochemically induced mechanical stresses are large enough to propagate lithium dendrites and subsequently fracture solid electrolytes. This study builds on this understanding and demonstrates that stress‐driven dendrite propagation can be controlled via deflection at weakly bonded internal interfaces. This approach, based on a fracture‐mechanics analysis of multilayered composites, is investigated with a variety of interlayer materials that are embedded into LLZTO. The viability and effectiveness of dendrite deflection are most clearly evident with reduced graphene oxide where the critical current density increased from 0.6 to 3.8 mA cm−2. In this material, both the weak interface with LLZTO and the mixed ionic–electronic conducting nature of the interlayer appear to contribute to the improved performance. Additional insight into the mechanics of multilayered electrolytes is also obtained with finite element modeling. The overall results present a promising proof‐of‐concept demonstration along with important generalized design guidelines for creating multilayered solid electrolyte architectures that can enable high‐performance solid‐state batteries. 
    more » « less
  4. ; ; ; ; ; ; ; ; ; (, Advanced Energy Materials)
    Abstract The development of all‐solid‐state Li‐ion batteries requires solid electrolyte materials with many desired properties, such as ionic conductivity, chemical and electrochemical stability, and mechanical durability. Computation‐guided materials design techniques are advantageous in designing and identifying new solid electrolytes that can simultaneously meet these requirements. In this joint computational and experimental study, a new family of fast lithium ion conductors, namely, LiTaSiO5with sphene structure, are successfully identified, synthesized, and demonstrated using a novel computational design strategy. First‐principles computation predicts that Zr‐doped LiTaSiO5sphene materials have fast Li diffusion, good phase stability, and poor electronic conductivity, which are ideal for solid electrolytes. Experiments confirm that Zr‐doped LiTaSiO5sphene structure indeed exhibits encouraging ionic conductivity. The lithium diffusion mechanisms in this material are also investigated, indicating the sphene materials are 3D conductors with facile 1D diffusion along the [101] direction and additional cross‐channel migration. This study demonstrates a novel design strategy of activating fast Li ionic diffusion in lithium sphenes, a new materials family of superionic conductors. 
    more » « less
  5. ; ; ; ; ; (, Advanced Energy Materials)
    Abstract The performance of all‐solid‐state batteries (ASSBs) relies on the Li+transport and stability characteristics of solid electrolytes (SEs). Li3PS4is notable for its stability against lithium metal, yet its ionic conductivity remains a limiting factor. This study leverages local structural disorder via O substitution to achieve an ionic conductivity of 1.38 mS cm−1with an activation energy of 0.34 eV for Li3PS4−xOx(x = 0.31). Optimal O substitution transforms Li+transport from 2D to 3D pathways with increased ion mobility. Li3PS3.69O0.31exhibits improvements in the critical current density and stability against Li metal and retains its electrochemical stability window compared with Li3PS4. The practical implementation of Li3PS3.69O0.31in ASSBs half‐cells, particularly when coupled with TiS2as the cathode active material, demonstrates substantially enhanced capacity and rate performance. This work elucidates the utility of introducing local structural disorder to ameliorate SE properties and highlights the benefits of strategically combining the inherent strengths of sulfides and oxides via creating oxysulfide SEs. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email