Metal‐assisted electrochemical nanoimprinting (Mac‐Imprint) scales the fabrication of micro‐ and nanoscale 3D freeform geometries in silicon and holds the promise to enable novel chip‐scale optics operating at the near‐infrared spectrum. However, Mac‐Imprint of silicon concomitantly generates mesoscale roughness (e.g., protrusion size ≈45 nm) creating prohibitive levels of light scattering. This arises from the requirement to coat stamps with nanoporous gold catalyst that, while sustaining etchant diffusion, imprints its pores (e.g., average diameter ≈42 nm) onto silicon. In this work, roughness is reduced to sub‐10 nm levels, which is in par with plasma etching, by decreasing pore size of the catalyst via dealloying in far‐from equilibrium conditions. At this level, single‐digit nanometric details such as grain‐boundary grooves of the catalyst are imprinted and attributed to the resolution limit of Mac‐Imprint, which is argued to be twice the Debye length (i.e., 1.7 nm)—a finding that broadly applies to metal‐assisted chemical etching. Last, Mac‐Imprint is employed to produce single‐mode rib‐waveguides on pre‐patterned silicon‐on‐insulator wafers with root‐mean‐square line‐edge roughness less than 10 nm while providing depth uniformity (i.e., 42.9 ± 5.5 nm), and limited levels of silicon defect formation (e.g., Raman peak shift < 0.1 cm−1) and sidewall scattering.
Silicon carbide (SiC) is a wide bandgap third‐generation semiconductor well suited for harsh environment power electronics, micro and nano electromechanical systems, and emerging quantum technology by serving as hosts for quantum states via defect centers. The chemical inertness of SiC limits viable etching techniques to plasma‐based reactive ion etching methods; however, these could have significant undesirable effects for electronic and photonic devices. This paper presents a plasma‐free, open‐circuit, photo‐induced metal‐assisted chemical etch for fabricating micro and nanoscale features without the inherent high energy ion‐related surface damage. The method presented herein utilizes above bandgap ultraviolet light, patterned noble metal (Pt), and a solution consisting of an oxidant potassium persulfate (K2S2O8) and an acid, hydrofluoric acid, to spatially define the etching morphology. The parameter space is comprehensively explored to demonstrate the controllability and versatility of this technique to produce ordered arrays of micro and nanoscale SiC structures with porous or solid sidewalls, and to elucidate the etching mechanism.
more » « less- NSF-PAR ID:
- 10368394
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Advanced Functional Materials
- Volume:
- 31
- Issue:
- 32
- ISSN:
- 1616-301X
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
Abstract -
Metal-mediated cross-coupling reactions offer organic chemists a wide array of stereo- and chemically-selective reactions with broad applications in fine chemical and pharmaceutical synthesis.1 Current batch-based synthesis methods are beginning to be replaced with flow chemistry strategies to take advantage of the improved consistency and process control methods offered by continuous flow systems.2,3 Most cross-coupling chemistries still encounter several issues in flow using homogeneous catalysis, including expensive catalyst recovery and air sensitivity due to the chemical nature of the catalyst ligands.1 To mitigate some of these issues, a ligand-free heterogeneous catalysis reaction was developed using palladium (Pd) loaded into a polymeric network of a silicone elastomer, poly(hydromethylsiloxane) (PHMS), that is not air sensitive and can be used with mild reaction solvents (ethanol and water).4 In this work we present a novel method of producing soft catalytic microparticles using a multiphase flow-focusing microreactor and demonstrate their application for continuous Suzuki-Miyaura cross-coupling reactions. The catalytic microparticles are produced in a coaxial glass capillary-based 3D flow-focusing microreactor. The microreactor consists of two precursors, a cross-linking catalyst in toluene and a mixture of the PHMS polymer and a divinyl cross-linker. The dispersed phase containing the polymer, cross-linker, and cross-linking catalyst is continuously mixed and then formed into microdroplets by the continuous phase of water and surfactant (sodium dodecyl sulfate) introduced in a counter-flow configuration. Elastomeric microdroplets with a diameter ranging between 50 to 300 micron are produced at 25 to 250 Hz with a size polydispersity less than 3% in single stream production. The physicochemical properties of the elastomeric microparticles such as particle swelling/softness can be tuned using the ratio of cross-linker to polymer as well as the ratio of polymer mixture to solvent during the particle formation. Swelling in toluene can be tuned up to 400% of the initial particle volume by reducing the concentration of cross-linker in the mixture and increasing the ratio of polymer to solvent during production.5 After the particles are produced and collected, they are transferred into toluene containing palladium acetate, allowing the particles to incorporate the palladium into the polymer network and then reduce the palladium to Pd0 with the Si-H functionality present on the PHMS backbones. After the reduction, the Pd-loaded particles can be washed and dried for storage or switched into an ethanol/water solution for loading into a micro-packed bed reactor (µ-PBR) for continuous organic synthesis. The in-situ reduction of Pd within the PHMS microparticles was confirmed using energy dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS) and focused ion beam-SEM, and TEM techniques. In the next step, we used the developed µ-PBR to conduct continuous organic synthesis of 4-phenyltoluene by Suzuki-Miyaura cross-coupling of 4-iodotoluene and phenylboronic acid using potassium carbonate as the base. Catalyst leaching was determined to only occur at sub ppm concentrations even at high solvent flow rates after 24 h of continuous run using inductively coupled plasma mass spectrometry (ICP-MS). The developed µ-PBR using the elastomeric microparticles is an important initial step towards the development of highly-efficient and green continuous manufacturing technologies in the pharma industry. In addition, the developed elastomeric microparticle synthesis technique can be utilized for the development of a library of other chemically cross-linkable polymer/cross-linker pairs for applications in organic synthesis, targeted drug delivery, cell encapsulation, or biomedical imaging. References 1. Ruiz-Castillo P, Buchwald SL. Applications of Palladium-Catalyzed C-N Cross-Coupling Reactions. Chem Rev. 2016;116(19):12564-12649. 2. Adamo A, Beingessner RL, Behnam M, et al. On-demand continuous-flow production of pharmaceuticals in a compact, reconfigurable system. Science. 2016;352(6281):61 LP-67. 3. Jensen KF. Flow Chemistry — Microreaction Technology Comes of Age. 2017;63(3). 4. Stibingerova I, Voltrova S, Kocova S, Lindale M, Srogl J. Modular Approach to Heterogenous Catalysis. Manipulation of Cross-Coupling Catalyst Activity. Org Lett. 2016;18(2):312-315. 5. Bennett JA, Kristof AJ, Vasudevan V, Genzer J, Srogl J, Abolhasani M. Microfluidic synthesis of elastomeric microparticles: A case study in catalysis of palladium-mediated cross-coupling. AIChE J. 2018;0(0):1-10.more » « less
-
more » « less
Circular microdisk mechanical resonators vibrating in their various resonance modes have emerged as important platforms for a wide spectrum of technologies including photonics, cavity optomechanics, optical metrology, and quantum optics. Optically transduced microdisk resonators made of advanced materials such as silicon carbide (SiC), diamond, and other wide- or ultrawide-bandgap materials are especially attractive. They are also of strong interest in the exploration of transducers or detectors for harsh environments and mission-oriented applications. Here we report on the first experimental investigation and analysis of energetic proton radiation effects on microdisk resonators made of 3C-SiC thin film grown on silicon substrate. We fabricate and study microdisks with diameters of ∼48 µm and ∼36 µm, and with multimode resonances in the ∼1 to 20 MHz range. We observe consistent downshifts of multimode resonance frequencies, and measure fractional frequency downshifts from the first three flexural resonance modes, up to ∼-3420 and -1660 ppm for two devices, respectively, in response to 1.8 MeV proton radiation at a dosage of 1014/cm2. Such frequency changes are attributed to the radiation-induced Young’s modulus change of ∼0.38% and ∼0.09%, respectively. These devices also exhibit proton detection responsivity of ℜ ≈ -5 to -6 × 10−6 Hz/proton. The results provide new knowledge of proton radiation effects in SiC materials, and may lead to better understanding and exploitation of micro/nanoscale devices for harsh-environment sensing, optomechanics, and integrated photonics applications.
-
more » « less
Abstract Inorganic particles are effective photocatalysts for the liquid-state production of organic precursors and monomers at ambient conditions. However, poor colloidal stability of inorganic micro- and nanoparticles in low-polarity solvents limits their utilization as heterogeneous catalysts and coating them with surfactants drastically reduces their catalytic activity. Here we show that effective photo-oxidation of liquid cyclohexane (CH) is possible using spiky particles from metal oxides with hierarchical structure combining micro- and nanoscale structural features engineered for enhanced dispersibility in CH. Nanoscale ZnO spikes are assembled radially on α-Fe2O3microcube cores to produce complex ‘hedgehog’ particles (HPs). The ‘halo’ of stiff spikes reduces van der Waals attraction, preventing aggregation of the catalytic particles. Photocatalysis in Pickering emulsions formed by HPs with hydrogen peroxide provides a viable pathway to energy-efficient alkane oxidation in the liquid state. Additionally, HPs enable a direct chemical pathway from alkanes to epoxides at ambient conditions, specifically to cyclohexene oxide, indicating that the structure of HPs has a direct effect on the recombination of ion-radicals during the hydrocarbon oxidation. These findings demonstrate the potential of inorganic photocatalysts with complex architecture for ‘green’ catalysis.
-
more » « less
N-polar AlGaN is an emerging wide-bandgap semiconductor for next-generation high electron mobility transistors and ultraviolet light emitting diodes and lasers. Here, we demonstrate the growth and characterization of high-quality N-polar AlGaN films on C-face 4H-silicon carbide (SiC) substrates by molecular beam epitaxy. On optimization of the growth conditions, N-polar AlGaN films exhibit a crack free, atomically smooth surface (rms roughness ∼ 0.9 nm), and high crystal quality with low density of defects and dislocations. The N-polar crystallographic orientation of the epitaxially grown AlGaN film is unambiguously confirmed by wet chemical etching. We demonstrate precise compositional tunability of the N-polar AlGaN films over a wide range of Al content and a high internal quantum efficiency ∼74% for the 65% Al content AlGaN film at room temperature. Furthermore, controllable silicon (Si) doping in high Al content (65%) N-polar AlGaN films has been demonstrated with the highest mobility value ∼65 cm2/V-s observed corresponding to an electron concentration of 1.1 × 1017 cm−3, whereas a relatively high mobility value of 18 cm2/V-s is sustained for an electron concentration of 3.2 × 1019 cm−3, with an exceptionally low resistivity value of 0.009 Ω·cm. The polarity-controlled epitaxy of AlGaN on SiC presents a viable approach for achieving high-quality N-polar III-nitride semiconductors that can be harnessed for a wide range of emerging electronic and optoelectronic device applications.
