Bubble nucleation is the critical first step during magma degassing. The resultant number density of bubbles provides a record of nucleation kinetics and underlying eruptive conditions. The rate of bubble nucleation is strongly dependent on the surface free energy associated with nucleus formation, making the use of bubble number density for the interpretation of eruptive conditions contingent upon a sound understanding of surface tension. Based on a suite of nucleation experiments with up to >1016bubbles per unit volume of melt, and using numerical simulations of bubble nucleation and growth during each experiment, we provide a new formulation for surface tension during homogeneous nucleation of H2O bubbles in rhyolitic melt. It is based on the Tolman correction with a Tolman length of
Theoretical studies of homogeneous cavitation have largely been based on the classical nucleation theory. However, existing cavitation models cannot adequately describe its dynamics at nanosecond timescale, which has been called for in other fields. We develop a model coupling nucleation kinetics with cavity growth and pressure feedback as saturation mechanisms. Our numerical studies reveal the exponential dependence of cavitation characteristics such as saturation cavity density and most probable cavity radius on model parameters: Tolman length and initial pressure. This work also sheds light on the possibility of accurately determining Tolman length, whose value has a large spread in the literature.
more » « less- Award ID(s):
- 2129409
- NSF-PAR ID:
- 10440385
- Publisher / Repository:
- American Institute of Physics
- Date Published:
- Journal Name:
- Physics of Fluids
- Volume:
- 34
- Issue:
- 10
- ISSN:
- 1070-6631
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
Abstract δ = 0.32 nm, which implies an increase in surface tension of bubbles with decreasing nucleus size. Our model results indicate that experiments encompass two distinct nucleation regimes, distinguishable by the ratio of the characteristic diffusion time of water,τ diff, to the decompression time,t d. Experiments with >1013 m−3bubbles are characterized byτ diff/t d≪ 1, wherein the nucleation rate predominantly depends on the interplay between decompression and diffusion rates. Nucleation occurs over a short time interval with nucleation rate peaks at high values. For experiments with comparatively low bubble number density the average distance between adjacent bubbles and the diffusion timescale is large. Consequently,τ diff/t d≫ 1 and nucleation is nearly unaffected by diffusion and independent of decompression rate, with bubbles nucleating at an approximately constant rate until the sample is quenched. -
more » « less
Abstract Cavitation has long been recognized as a crucial predictor, or precursor, to the ultimate failure of various materials, ranging from ductile metals to soft and biological materials. Traditionally, cavitation in solids is defined as an unstable expansion of a void or a defect within a material. The critical applied load needed to trigger this instability -- the critical pressure -- is a lengthscale independent material property and has been predicted by numerous theoretical studies for a breadth of constitutive models. While these studies usually assume that cavitation initiates from defects in the bulk of an otherwise homogeneous medium, an alternative and potentially more ubiquitous scenario can occur if the defects are found at interfaces between two distinct media within the body. Such interfaces are becoming increasingly common in modern materials with the use of multimaterial composites and layer-by-layer additive manufacturing methods. However, a criterion to determine the threshold for interfacial failure, in analogy to the bulk cavitation limit, has yet to be reported. In this work, we fill this gap. Our theoretical model captures a lengthscale independent limit for interfacial cavitation, and is shown to agree with our observations at two distinct lengthscales, via two different experimental systems. To further understand the competition between the two cavitation modes (bulk versus interface), we expand our investigation beyond the elastic response to understand the ensuing unstable propagation of delamination at the interface. A phase diagram summarizes these results, showing regimes in which interfacial failure becomes the dominant mechanism.
-
We present a complete open-hardware and software materials acceleration platform (MAP) for sonochemical synthesis of nanocrystals using a versatile tool-changing platform (Jubilee) configured for automated ultrasound application, a liquid-handling robot (Opentrons OT2) and a well-plate spectrometer. An automated high-throughput protocol was developed demonstrating the synthesis of CdSe nanocrystals using sonochemistry and different combinations of sample conditions, including precursor and ligand compositions and concentrations. Cavitation caused by ultrasound fields causes local and transient increases in temperature and pressure sufficient to drive the decomposition of organometallic precursors to drive the chemical reaction leading to nanocrystal formation. A total of 625 unique sample conditions were prepared and analyzed in triplicate with an individual sample volume of as little as 0.5 mL, which drastically reduced chemical waste and experimental times. The rapid onset of cavitation and quick dissipation of energy result in fast nucleation with little nanocrystal growth leading to the formation of small nanocrystals or magic-size clusters (MSCs) depending on composition. Using the effective mass approximation, the calculated QD diameters obtained under all our experimental conditions ranged between 1.3 and 2.1 nm, which was also validated with small angle X-ray scattering (SAXS). Polydispersity, QD shape and optical properties largely varied depending on the concentration of ligands present in solution. Statistical analysis of the spectroscopic data corroborates the qualitative relationships observed from the optical characterization of the samples with the model-agnostic SHAP analysis. The complete workflow relies on relatively low-cost and open-source systems. Automation and the reduced volumes also allow for cost-efficient experimentation, increasing the accessibility of this MAP. The high-throughput capabilities of the automated sonication platform, the extensible nature of the Jubilee system, and the modular nature of the protocol, make the workflow adaptable to a variety of future studies, including other nanocrystal design spaces, emulsification processes, and nanoparticle re-dispersion or exfoliation.more » « less
-
This article studies equilibrium singular configurations of gels and addresses open questions concerning gel energetics. We model a gel as an incompressible, immiscible and saturated mixture of a solid polymer and a solvent that sustain chemical interactions at the molecu- lar level. We assume that the energy of the gel consists of the elastic energy of its polymer network plus the Flory-Huggins energy of mixing. The latter involves the entropic energies of the individual components plus that of interaction between polymer and solvent, with the temperature dependent Flory parameter, χ , encoding properties of the solvent. In particular, a good solvent promoting the mixing regime, is found below the threshold value χ = 0.5, whereas the phase separating regime develops above that critical value. We show that cavi- ties and singularities develop in the latter regime. We find two main classes of singularities: (i) drying out of the solvent, with water possibly exiting the gel domain through the bound- ary, leaving behind a core of exposed polymer at the centre of the gel; (ii) cavitation, in response to traction on the boundary or some form of negative pressure, with a cavity that can be either void or flooded by the solvent. The straightforward and unified mathematical approach to treat all such singularities is based on the construction of appropriate test func- tions, inspired by the particular states of uniform swelling or compression. The last topic of the article addresses a statistical mechanics rooted controversy in the research commu- nity, providing an experimental and analytic study in support of the phantom elastic energy versus the affine one.more » « less
-
In the present study, the flow inside a real size Diesel fuel injector nozzle was modeled and analyzed under different boundary conditions using ANSYS-Fluent software. A validation was performed by comparing our numerical results with previous experimental data for a rectangular shape nozzle. Schnerr-Sauer cavitation model, which was selected for this study, was also validated. Two-equation k-ε turbulence model was selected since it had good agreement with experimental data. To reduce the computing time, due to symmetry of this nozzle, only one-sixth of this nozzle was modeled. Our present six-hole Diesel injector nozzle was modeled with different needle lifts including 30 μm, 100 μm and 250 μm. Effects of different needle lifts on mass flow rate, discharge coefficient and length of cavitation were evaluated comprehensively. Three different fuels including one Diesel fuel and two bio-Diesel fuels were also included in these numerical simulations. Behavior of these fuels was investigated for different needle lifts and pressure differences. For comparing the results, discharge coefficient, mass flow rate and length of cavitation region were compared under different boundary conditions and for several fuel types. The extreme temperature spike at the center of an imploding cavitation bubble was also analyzed as a function of time and initial bubble size.more » « less
