skip to main content


Title: Na‐Rich Na 3 V 2 (PO 4 ) 3 Cathodes for Long Cycling Rechargeable Sodium Full Cells
Abstract

NASICON‐type sodium vanadium phosphate (Na3V2(PO4)3, or NVP) cathode materials have great potential for fast charging and long cycling sodium‐ion batteries (SIBs) similar to lithium iron phosphate (LiFePO4, or LFP) cathode materials used in lithium‐ion batteries (LIBs). However, the cycle life and energy density in the full cell using NVP materials need to be significantly improved. This paper investigates the degradation mechanisms of NVP‐based SIBs and identifies the Na loss from the cathode to the anode solid electrolyte interphase (SEI) reactions as the main cause of capacity degradation. A new Na‐rich NVP cathode (e.g., Na4V2(PO4)3, or Na4VP) is developed to address the Na loss problem. Conventional NVP can be easily transformed into the Na4VP by a facile and fast chemical solution treatment (30 s). Na‐free‐anode Na4VP and hard carbon‐Na4VP full cells are assembled to evaluate the electrochemical properties of the Na‐rich NVP cathode. The Na4VP cathode provides excess Na to compensate for the Na loss, resulting much longer cycle life in the full cells (>400 cycles) and a high specific energy and power density. Good low‐temperature performance is also observed.

 
more » « less
NSF-PAR ID:
10384412
Author(s) / Creator(s):
 ;  ;  ;  ;  ;  ;  ;  
Publisher / Repository:
Wiley Blackwell (John Wiley & Sons)
Date Published:
Journal Name:
Advanced Energy Materials
Volume:
13
Issue:
3
ISSN:
1614-6832
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. Abstract

    Sodium ion batteries have attracted much attention in recent years, due to the higher abundance and lower cost of sodium, as an alternative to lithium ion batteries. However, a major challenge is their lower energy density. In this work, we report a novel multi‐electron cathode material, KVOPO4, for sodium ion batteries. Due to the unique polyhedral framework, the V3+↔ V4+↔ V5+redox couple was for the first time fully activated by sodium ions in a vanadyl phosphate phase. The KVOPO4based cathode delivered reversible multiple sodium (i.e. maximum 1.66 Na+per formula unit) storage capability, which leads to a high specific capacity of 235 Ah kg−1. Combining an average voltage of 2.56 V vs. Na/Na+, a high practical energy density of over 600 Wh kg−1was achieved, the highest yet reported for any sodium cathode material. The cathode exhibits a very small volume change upon cycling (1.4% for 0.64 sodium and 8.0% for 1.66 sodium ions). Density functional theory (DFT) calculations indicate that the KVOPO4framework is a 3D ionic conductor with a reasonably, low Na+migration energy barrier of ≈450 meV, in line with the good rate capability obtained.

     
    more » « less
  2. Metal-ion batteries (e.g., lithium and sodium ion batteries) are the promising power sources for portable electronics, electric vehicles, and smart grids. Recent metal-ion batteries with organic liquid electrolytes still suffer from safety issues regarding inflammability and insufficient lifetime.1 As the next generation energy storage devices, all-solid-state batteries (ASSBs) have promising potentials for the improved safety, higher energy density, and longer cycle life than conventional Li-ion batteries.2 The nonflammable solid electrolytes (SEs), where only Li ions are mobile, could prevent battery combustion and explosion since the side reactions that cause safety issues as well as degradation of the battery performance are largely suppressed. However, their practical application is hampered by the high resistance arising at the solid–solid electrode–electrolyte interface (including cathode-electrolyte interface and anode-electrolyte interface).3 Several methods have been introduced to optimize the contact capability as well as the electrochemical/chemical stability between the metal anodes (i.e.: Li and Na) and the SEs, which exhibited decent results in decreasing the charge transfer resistance and broadening the range of the stable energy window (i.e., lowing the chemical potential of metal anode below the highest occupied molecular orbital of the SEs).4 Nevertheless, mitigation for the cathode in ASSB is tardily developed because: (1) the porous structure of the cathode is hard to be infiltrated by SEs;5 (2) SEs would be oxidized and decomposed by the high valence state elements at the surface of the cathode at high state of charge.5 Herein, we demonstrate a universal cathode design strategy to achieve superior contact capability and high electrochemical/chemical stability with SEs. Stereolithography is adopted as a manufacturing technique to realize a hierarchical three-dimensional (HTD) electrode architecture with micro-size channels, which is expected to provide larger contact areas with SEs. Then, the manufactured cathode is sintered at 700 °C in a reducing atmosphere (e.g.: H2) to accomplish the carbonization of the resin, delivering sufficiently high electronic conductivity for the cathode. To avoid the direct exposure of the cathode active materials to the SEs, oxidative chemical vapor deposition technique (oCVD) is leveraged to build conformal and highly conducting poly(3,4-ethylenedioxythiophene) (PEDOT) on the surface of the HTD cathode.6 To demonstrate our design strategy, both NCM811 and Na3V2(PO4)3 is selected as active materials in the HTD cathode, then each cathode is paired with organic (polyacrylonitrile-based) and inorganic (sulfur-based) SEs assembled into two batteries (total four batteries). SEM and TEM reveal the micro-size HTD structure with built-in channels. Featured by the HTD architecture, the intrinsic kinetic and thermodynamic conditions will be enhanced by larger surface contact areas, more active sites, improved infusion and electrolyte ion accessibility, and larger volume expansion capability. Disclosed by X-ray computed tomography, the interface between cathode and SEs in the four modified samples demonstrates higher homogeneity at the interface between the cathode and SEs than that of all other pristine samples. Atomic force microscopy is employed to measure the potential image of the cross-sectional interface by the peak force tapping mode. The average potential of modified samples is lower than that of pristine samples, which confirms a weakened space charge layer by the enhanced contact capability. In addition, through Electron Energy Loss Spectroscopy coupled with Scanning Transmission Electron Microscopy, the preserved interface between HTD cathode and SE is identified; however, the decomposing of the pristine cathode is clearly observed. In addition, Finite element method simulations validate that the diffusion dynamics of lithium ions is favored by HTD structure. Such a demonstrated universal strategy provides a new guideline to engineer cathode electrolyte interface by reconstructing electrode structures that can be applicable to all solid-state batteries in a wide range of chemical conditions. 
    more » « less
  3. Abstract

    All‐solid‐state rechargeable sodium (Na)‐ion batteries are promising for inexpensive and high‐energy‐density large‐scale energy storage. In this contribution, new Na solid electrolytes, Na3−yPS4−xClx, are synthesized with a strategic approach, which allows maximum substitution of Cl for S (x= 0.2) without significant compromise of structural integrity or Na deficiency. A maximum conductivity of 1.96 mS cm−1at 25 °C is achieved for Na3.0PS3.8Cl0.2, which is two orders of magnitude higher compared with that of tetragonal Na3PS4(t‐Na3PS4). The activation energy (Ea) is determined to be 0.19 eV. Ab initio molecular dynamics simulations shed light on the merit of maximizing Cl‐doping while maintaining low Na deficiency in enhanced Na‐ion conduction. Solid‐state nuclear magnetic resonance (NMR) characterizations confirm the successful substitution of Cl for S and the resulting change of P oxidation state from 5+ to 4+, which is also verified by spin moment analysis. Ion transport pathways are determined with a tracer‐exchange NMR method. The functional detects that promote Na ‐ion transport are maximized for further improvement in ionic conductivity. Full‐cell performance is demonstrated using Na/Na3.0PS3.8Cl0.2/Na3V2(PO4)3with a reversible capacity of ≈100 mAh g‐1at room temperature.

     
    more » « less
  4. Abstract

    Given the high energy density, alkali metals are preferred in rechargeable batteries as anodes, however, with significant limitations such as dendrite growth and volume expansion, leading to poor cycle life and safety concerns. Herein a room‐temperature liquid alloy system is proposed as a possible solution for its self‐recovery property. Full extraction of alkali metal ions from the ternary alloy brings it back to the binary liquid eutectic, and thus enables a self‐healing process of the cracked or pulverized structure during cycling. A half‐cell discharge specific capacity of up to 706.0 mAh g−1in lithium‐ion battery and 222.3 mAh g−1for sodium‐ion battery can be delivered at 0.1C; at a high rate of 5C, a sizable capacity of over 400 mAh g−1for Li and 60 mAh g−1for Na could be retained. Li and Na ion full cells with considerable stability are demonstrated when pairing liquid metal with typical cathode materials, LiFePO4, and P2‐Na2/3[Ni1/3Mn2/3]O2. Remarkable cyclic durability, considerable theoretical capacity utilization, and reasonable rate stability present in this work allow this novel anode system to be a potential candidate for rechargeable alkali‐ion batteries.

     
    more » « less
  5. Abstract

    Sodium‐metal batteries (SMBs) are considered as a compliment to lithium‐metal batteries for next‐generation high‐energy batteries because of their low cost and the abundance of sodium (Na). Herein, a 3D nanostructured porous carbon particle containing carbon‐shell‐coated Fe nanoparticles (PC‐CFe) is employed as a highly reversible Na‐metal host. PC‐CFe has a unique 3D hierarchy based on sub‐micrometer‐sized carbon particles, ordered open channels, and evenly distributed carbon‐coated Fe nanoparticles (CFe) on the surface. PC‐CFe achieves high reversibility of Na plating/stripping processes over 500 cycles with a Coulombic efficiency of 99.6% at 10 mA cm–2with 10 mAh cm–2in Na//Cu asymmetric cells, as well as over 14 400 cycles at 60 mA cm–2in Na//Na symmetric cells. Density functional theory calculations reveal that the superior cycling performance of PC‐CFe stems from the stronger adsorption of Na on the surface of the CFe, providing initial nucleation sites more favorable to Na deposition. Moreover, the full cell with a PC‐CFe host without Na metal and a high‐loading Na3V2(PO4)3cathode (10 mg cm–2) maintains a high capacity of 103 mAh g–1at 1 mA cm–2even after 100 cycles, demonstrating the operation of anode‐free SMBs.

     
    more » « less