skip to main content


Title: Batteryless, Wireless, and Secure SoC for Implantable Strain Sensing
The past few years have witnessed a growing interest in wireless and batteryless implants, due to their potential in long-term biomedical monitoring of in-body conditions such as internal organ movements, bladder pressure, and gastrointestinal health. Early proposals for batteryless implants relied on inductive near-field coupling and ultrasound harvesting, which require direct contact between the external power source and the human body. To overcome this near-field challenge, recent research has investigated the use of RF backscatter in wireless micro-implants because of its ability to communicate with wireless receivers that are placed at a distance outside the body (∼0.5 m), allowing a more seamless user experience. Unfortunately, existing far-field backscatter designs remain limited in their functionality: they cannot perform biometric sensing or secure data transmission; they also suffer from degraded harvesting efficiency and backscatter range due to the impact of variations in the surrounding tissues. In this paper, we present the design of a batteryless, wireless and secure system-on-chip (SoC) implant for in-body strain sensing. The SoC relies on four features: 1) employing a reconfigurable in-body rectenna which can operate across tissues adapting its backscatter bandwidth and center frequency; 2) designing an energy efficient 1.37 mmHg strain sensing front-end with an efficiency of 5.9 mmHg·nJ/conversion; 3) incorporating an AES-GCM security engine to ensure the authenticity and confidentiality of sensed data while sharing the ADC with the sensor interface for an area efficient random number generation; 4) implementing an over-the-air closed-loop wireless programming scheme to reprogram the RF front-end to adapt for surrounding tissues and the sensor front-end to achieve faster settling times below 2 s.  more » « less
Award ID(s):
1844280
NSF-PAR ID:
10393533
Author(s) / Creator(s):
; ; ; ;
Date Published:
Journal Name:
IEEE Open Journal of the Solid-State Circuits Society
ISSN:
2644-1349
Page Range / eLocation ID:
1 to 1
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. There is a growing interest in wireless and batteryless implants for long-term sensing of organ movements, core pressure, glucose levels, or other biometrics [1]. Most research on such implants has focused on ultrasonic [2] and nearfield inductive [3-4] methods for power and communication, which require direct contact or close proximity (<1-5cm) to the human body. Recently, RF backscatter has emerged as a promising alternative due to its ability to communicate with far-field (> 10cm) wireless devices at ultra-low-power [5]. While multiple proposals have demonstrated far-field RF backscatter in deep tissues, these proposals have been limited to tag identification and could neither perform biometric sensing nor secure the wireless communication links, which is critical for ensuring the confidentiality of the sensed biometrics and for responding to commands only from authorized users [6]. Moreover, such far-field RF implants are susceptible to tissue variations which impact their resonance and hence their efficiency in RF backscatter and energy harvesting. 
    more » « less
  2. This paper presents the design, implementation, and experimental evaluation of a wireless biomedical implant platform exploiting the magnetoelectric effect for wireless power and bi-directional communication. As an emerging wireless power transfer method, magnetoelectric is promising for mm-scaled bio-implants because of its superior misalignment sensitivity, high efficiency, and low tissue absorption compared to other modalities [46, 59, 60]. Utilizing the same physical mechanism for power and communication is critical for implant miniaturization, but low-power magnetoelectric uplink communication has not been achieved yet. For the first time, we design and demonstrate near-zero power magnetoelectric backscatter from the mm-sized implants by exploiting the converse magnetostriction effects. The system for demonstration consists of an 8.2-mm3 wireless implantable device and a custom portable transceiver. The implant's ASIC interfacing with the magnetoelectric transducer encodes uplink data by changing the transducer's load, resulting in resonance frequency changes for frequency-shift-keying modulation. The magnetoelectrically backscattered signal is sensed and demodulated through frequency-to-digital conversion by the external transceiver. With design optimizations in data modulation and recovery, the proposed system archives > 1-kbps data rate at the 335-kHz carrier frequency, with a communication distance greater than 2 cm and a bit error rate less than 1E-3. Further, we validate the proposed system for wireless stimulation and sensing, and conducted ex-vivo tests through a 1.5-cm porcine tissue. The proposed magnetoelectric backscatter approach provides a path towards miniaturized wireless bio-implants for advanced biomedical applications like closed-loop neuromodulation. 
    more » « less
  3. We propose a sensing system comprising a large network of tiny, battery-less, Radio Frequency (RF)-powered sensors that use backscatter communication. The sensors use an entirely passive technique to 'sense' the parameters of the wireless channel between themselves. Since the material properties influence RF channels, this fine-grain sensing can uncover multiple material properties both at a large scale and fine spatial resolution. In this paper, we study the feasibility of the proposed passive technique for monitoring parameters of material in which the sensors are embedded. We performed a set of experiments where the sensor-to-sensor wireless channel parameters are well-defined using physics-based modeling, and we compared the theoretical and experimentally obtained values. For some material parameters of interest, like humidity or strain, the relationship with the observed wireless channel parameters have to be modeled relying on data-driven approaches. The initial experiments show an observable difference in the sensor-to-sensor channel phase with variation in the applied weights. 
    more » « less
  4. This paper presents a self-powered motion sensor based on reverse-electrowetting on dielectric (REWOD) energy harvesting having the capability of remotely keeping a track of any motion activity. The energy harvester includes a rectifier and a voltage regulator to provide the DC supply voltage to the analog front-end and the transmitter to wirelessly transfer the data from the motion sensor. The on-chip circuitry includes a seven-stage voltage-doubler based rectifier, an amplifier, an analog-to-digital converter (ADC), and a transmitter, and is designed in standard 180 nm CMOS process with a supply voltage of 1.8 V. The recycled folded cascode (RFC) based charge amplifier has a closed-loop gain of 53 dB within the bandwidth of 1-150 Hz, which is suitable to detect any low-frequency motion signal. An 8-bit SAR-ADC is designed to digitize the amplified signal with a sampling rate of 1 ksamples/s. The transmitter used for this application operates in the 3.1-5 GHz frequency band with an energy efficiency of 8.5 pJ/pulse at 100 kbps data rate. The wireless motion sensing device with the REWOD can be suitable for quantitatively monitoring the motion-related data as a wearable sensor. 
    more » « less
  5. null (Ed.)
    The principle of backscattering has the potential to enable a full realization of the Internet of Things. This paradigm subsumes massively deployed things that have the capability to communicate directly with each other. Based on the types of excitation and receivers, we discriminate four types of backscattering systems: (i) Dedicated Exciter Active Receiver systems, (ii) Ambient Exciter Active Receiver systems, (iii) Dedicated Exciter Passive Receiver systems, and (iv) Ambient Exciter Passive Receiver systems. In this paper, we present an overview of bacskscattering systems with passive receivers which form the foundation for Backscattering Tag-to-Tag Networks (BTTNs). This is a technology that allows tiny batteryless RF tags attached to various objects to communicate directly with each other and to perform RF-based sensing of the communication link. We present an overview of recent innovations in hardware architectures for backscatter modulation, passive demodulation, and energy harvesting that overcome design challenges for passive tag-to-tag communication. We further describe the challenges in scaling up the architecture from a single link to a distributed network. We provide some examples of application scenarios enabled by BTTNs involving object-to-object communication and inter-object or human-object dynamic interactions. Finally, we discuss key challenges in present-day BTTN technology and future research directions. 
    more » « less