An official website of the United States government
Abstract The hydrous mineral talc is stable over a relatively large P‐T field and can form due to fluid migration and metamorphic reactions in mafic and ultramafic rocks and in faults along plate boundary interfaces. Talc is known to be one of the weakest minerals, making it potentially important for the deformation dynamics and seismic characteristics of faults. However, little is known about talc's mechanical properties at high temperatures under confining pressures greater than 0.5 GPa. We present results of deformation experiments on natural talc cylinders exploring talc rheology under 0.5–1.5 GPa and 400–700°C, P‐T conditions simulating conditions at deep faults and subducted slab interface. At these pressures, the strength of talc is highly temperature‐dependent where the thermal weakening is associated with an increased tendency for localization. The strength of talc and friction coefficient inferred from Mohr circle analysis is between 0.13 at 400°C to ∼0.01 at 700°C. Strength comparison with other phyllosilicates highlights talc as the weakest mineral, a factor of ∼3–4 weaker than antigorite and a factor of ∼2 weaker than chlorite. The observed friction coefficients for talc are consistent with those inferred for subducted slabs and the San Andreas fault. We conclude that the presence of talc may explain the low strength of faults and of subducted slab interface at depths where transient slow slip events occur.
more »
« less
Semi‐Brittle Deformation of Talc at the Base of the Seismogenic Zone
Abstract Talc is commonly found in the cores of exhumed faults and may be important to the dynamics of slip in active fault zones. To understand the rheology of talc at conditions relevant to subduction zones, we conducted torsional deformation experiments at high pressure (1 GPa) and temperatures (450–500°C). Scanning Transmission Electron Microscope imaging revealed a marked decrease in grain size with increasing strain, in addition to the development of grain kinking and nanoporosity. The similarity of these microstructures to talc deformed in natural faults and low‐pressure experiments indicates that the dominant deformation mechanisms of talc are similar across a wide range of depths. We conclude that frictional processes remain an important control on talc rheology even under high normal stresses. However, deformation‐induced porosity could enhance the percolation of high‐pressure or reactive fluids through talc‐rich lithologies.
more »
« less
- Award ID(s):
- 1848824
- PAR ID:
- 10406794
- Publisher / Repository:
- DOI PREFIX: 10.1029
- Date Published:
- Journal Name:
- Geophysical Research Letters
- Volume:
- 50
- Issue:
- 8
- ISSN:
- 0094-8276
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Talc is expected to be an important water carrier in Earth's upper mantle, and understanding its electrical and seismic properties under high pressure and temperature conditions is required to detect possible talc‐rich regions in subduction zones imaged using geophysical observations. We conducted acoustic and electrical experiments on natural talc aggregates at relevant pressure‐temperature conditions. Compressional wave velocity (Vp) was measured using ultrasonic interferometry in a Paris‐Edinburgh press at pressures up to 3.4 GPa and temperatures up to 873 K. Similar Vp values are obtained regardless of the initial crystallographic preferred orientation of the samples, which can be explained by talc grain reorientation during the experiment, with the (001) plane becoming perpendicular to the uniaxial compression axis. Electrical conductivity of the same starting material was determined using impedance spectroscopy in a multi‐anvil press up to 6 GPa and 1263 K. Two conductivity jumps are observed, at ∼860–1025 K and ∼940–1080 K, depending on pressure, and interpreted as talc dehydroxylation and decomposition, respectively. Electrical anisotropy is observed at low temperature and decreases with increasing pressure (∼10 at 1.5 GPa and ∼2 at 3.5 GPa). Comparison of acoustic and electrical results with geophysical observations in central Mexico supports the presence of a talc‐bearing layer atop the subducted Cocos plate.more » « less
-
Abstract Localized frictional sliding on faults in the continental crust transitions at depth to distributed deformation in viscous shear zones. This brittle‐ductile transition (BDT), and/or the transition from velocity‐weakening (VW) to velocity‐strengthening (VS) friction, are controlled by the lithospheric thermal structure and composition. Here, we investigate these transitions, and their effect on the depth extent of earthquakes, using 2D antiplane shear simulations of a strike‐slip fault with rate‐and‐state friction. The off‐fault material is viscoelastic, with temperature‐dependent dislocation creep. We solve the heat equation for temperature, accounting for frictional and viscous shear heating that creates a thermal anomaly relative to the ambient geotherm which reduces viscosity and facilitates viscous flow. We explore several geotherms and effective normal stress distributions (by changing pore pressure), quantifying the thermal anomaly, seismic and aseismic slip, and the transition from frictional sliding to viscous flow. The thermal anomaly can reach several hundred degrees below the seismogenic zone in models with hydrostatic pressure but is smaller for higher pressure (and these high‐pressure models are most consistent with San Andreas Fault heat flow constraints). Shear heating raises the BDT, sometimes to where it limits rupture depth rather than the frictional VW‐to‐VS transition. Our thermomechanical modeling framework can be used to evaluate lithospheric rheology and thermal models through predictions of earthquake ruptures, postseismic and interseismic crustal deformation, heat flow, and the geological structures that reflect the complex deformation beneath faults.more » « less
-
Abstract Critical processes including seismic faulting, reservoir compartmentalization, and borehole failure involve high‐pressure mechanical behavior and strain localization of sedimentary rocks such as sandstone. Sand is often used as a model material to study the mechanical behavior of poorly lithified sandstone. Recent studies exploring the multi‐scale mechanics of sand have characterized the brittle, low‐pressure regime of behavior; however, limited work has provided insights into the ductile, high‐pressure regime of behavior viain‐situmeasurements. Critical features of the ductile regime, including grain breakage, grain micromechanics, and volumetric strain behavior therefore remain under‐explored. Here, we use a new high‐pressure triaxial apparatus within‐situx‐ray tomography to provide new insights into deformation banding, grain breakage, and grain micromechanics in Ottawa sand subjected to triaxial compression under confining pressures between 10 and 45 MPa. We observed strain‐hardening at pressures above 15 MPa and strain‐neutral responses at pressures below 15 MPa. Compacting shear bands and grain breakage were observed at all pressures with no significant variation due to grain size, except for minor increases in breakage in less‐rounded sands. Grain breakage emerged at stress levels lower than the assumed yield threshold and more intense breakage was associated with thinner deformation bands. Contact sliding at inter‐grain contacts demonstrated a bifurcation into a bimodal distribution, with intense sliding within deformation bands and reduced but non‐negligible sliding outside of deformation bands, suggesting that off‐band zones remain mechanically active during strain hardening.more » « less
-
Abstract Faults can release energy via a variety of different slip mechanisms ranging from steady creep to fast and destructive earthquakes. Tying the rheology of the crust to various slip dynamics is important for our understanding of plate tectonics and earthquake generation. Here we propose that the interplay of fractures and viscous flow leads to a spectrum between stick‐slip and creep. We use an elasto‐visco‐plastic rock analog (Carbopol U‐21) where we vary the yield stress to investigate its impact on slip dynamics in shear experiments. The experiments are performed using a simple shear apparatus, which provides distributed shear across the entire width of the experiment and allows in situ observations of deformation. We record force and displacement during deformation and use time lapse photography to document fracture development. A low yield stress (25 Pa) leads to creep dynamics in the absence of fractures. An intermediate yield stress (144 Pa) leads to the development and interaction of opening (mode I) and shear (mode II) fractures. This interaction leads to a spectrum in slip dynamics ranging from creep to stick‐slip. A high yield stress (357 Pa) results in the development of many mode I fractures and a deformation signal dominated by stick‐slip. These results show that bulk yield stress, fracture formation, and slip dynamics are closely linked and can lead to a continuum between creep and stick‐slip. We suggest that rheology should be considered as an additional mechanism to explain the broad range of slip dynamics in natural faults.more » « less
