skip to main content


Title: Thermal transport in 3D printed shape memory polymer metamaterials
Shape memory polymers are gaining significant interest as one of the major constituent materials for the emerging field of 4D printing. While 3D-printed metamaterials with shape memory polymers show unique thermomechanical behaviors, their thermal transport properties have received relatively little attention. Here, we show that thermal transport in 3D-printed shape memory polymers strongly depends on the shape, solid volume fraction, and temperature and that thermal radiation plays a critical role. Our infrared thermography measurements reveal thermal transport mechanisms of shape memory polymers in varying shapes from bulk to octet-truss and Kelvin-foam microlattices with volume fractions of 4%–7% and over a temperature range of 30–130 °C. The thermal conductivity of bulk shape memory polymers increases from 0.24 to 0.31 W m −1  K −1 around the glass transition temperature, in which the primary mechanism is the phase-dependent change in thermal conduction. On the contrary, thermal radiation dominates heat transfer in microlattices and its contribution to the Kelvin-foam structure ranges from 68% to 83% and to the octet-truss structure ranges from 59% to 76% over the same temperature range. We attribute this significant role of thermal radiation to the unique combination of a high infrared emissivity and a high surface-to-volume ratio in the shape memory polymer microlattices. Our work also presents an effective medium approach to explain the experimental results and model thermal transport properties with varying shapes, volume fractions, and temperatures. These findings provide new insights into understanding thermal transport mechanisms in 4D-printed shape memory polymers and exploring the design space of thermomechanical metamaterials.  more » « less
Award ID(s):
1902685 1935371
NSF-PAR ID:
10407703
Author(s) / Creator(s):
; ; ; ; ;
Date Published:
Journal Name:
APL Materials
Volume:
10
Issue:
8
ISSN:
2166-532X
Page Range / eLocation ID:
081105
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. Abstract

    Shape morphing materials have been extensively studied to control the formation of sophisticated three-dimensional (3D) structures and devices for a broad range of applications. Various methods, including the buckling of pre-strained bilayer composites, stimuli-responsive shape-shifting of shape memory polymers, and hydrogels, have been previously employed to transform 2D sheets to 3D structures and devices. However, the residual stress locked in these shape-shifting structures will drive them to gradually revert to their original layouts upon the removal of external stimuli or constrains. Here, we report a multistimuli-responsive vitrimer (m-vitrimer) bearing thermal- and photo-reversible disulfide bonds as shape programmable and healable materials for functional 3D devices. The mechanical properties and thermomechanical properties of vitrimer were tuned by altering the disulfide content and catalyst loading. Heat and light exposure induces effective stress relaxation and network rearrangement, enabling material shape programming and healing. We demonstrate that printed flexible smart electronics are fabricated using the m-vitrimer as a matrix and printed conductive silver nanoparticles as conductive wire. The printed electronics possess good electro-mechanical properties, strong interfacial bonding, and thermal- and photo-responsive shape programming. Moreover, the m-vitrimer can be healed upon damage by heat and light, which partially restores silver conductivity and protect the electronics from further damage. The converging of multi-stimuli-responsive polymers and printed electronics for functional 3D devices have the potential of finding broad applications in smart and morphing electronics, biomedical devices, and 4D printing.

     
    more » « less
  2. null (Ed.)
    Acoustic/elastic metamaterials that rely on engineered microstructures instead of chemical composition enable a rich variety of extraordinary effective properties that are suited for various applications including vibration/noise isolation, high-resolution medical imaging, and energy harvesting and mitigation. However, the static nature of these elastic wave guides limits their potential for active elastic-wave guiding, as microstructure transformation remains a challenge to effectively apply in traditional elastic metamaterials due to the interplay of polarization and structural sensitivity. Here, a tunable, locally resonant structural waveguide is proposed and demonstrated for active vibration bandgap switching and elastic-wave manipulation between 1000–4000 Hz based on 3D printed building blocks of zinc-neutralized poly(ethylene- co -methacrylic acid) ionomer (Surlyn 9910). The ionomer exhibits shape memory behavior to enable rearrangement into new shape patterns through application of thermal stimuli that tunes mechanical performance in both space and time dimensions (4D metamaterial). The thermally induced shape-reorganization is programed to flip a series of frequency bands from passbands to bandgaps and vice versa . The continuously switched bandwidth can exceed 500 Hz. Consequently, altering the bandgap from “on” to “off” produces programmable elastic-wave propagation paths to achieve active wave guiding phenomena. An anisotropic cantilever-in-mass model is demonstrated to predict the self-adaptive dynamic responses of the printed structures with good agreement between the analytical work and experimental results. The tunable metamaterial-based waveguides illustrate the potential of 4D printed shape memory polymers in the designing and manufacturing of intelligent devices for elastic-wave control and vibration isolation. 
    more » « less
  3. Abstract

    Shape‐memory resists capable of high‐resolution curing into arbitrarily designed structures are increasingly demanded for soft robotics, optical sensors, microscale manufacturing, and biomedicine. Amorphous, shape‐memory thiol‐vinyl networks are printed using two‐photon polymerization (2PP) curing of a simple resin formulated with commercially available reagents. The ability to print high‐resolution feature sizes down to 200 nm is attributed to the use of radical‐mediated, thiol‐vinyl step‐growth polymerization that quickly cross‐links the resin, limiting diffusive transport. The thermomechanical behavior of the 2PP‐cured material analyzed in compression, tension, and three‐point bending is similar to the behavior of the UV‐polymerized samples. To demonstrate the ability to design, field, and test 4D responsive microstructures, an array of nine springs with coil diameters of 330 µm is printed. Following compressive shape‐fixing, printed arrays can release 11 µJ of stored elastic strain energy when reheated. Further, a new concept of dichroic‐memory of a metamaterial device is demonstrated by printing a twisted woodpile structure with circular dichroism as characterized by Mueller Matrix ellipsometry. The results of this study demonstrate how combining high‐resolution 2PP curing with stimuli‐responsive molecular architectures can further the engineering of responsive microstructures and metamaterials.

     
    more » « less
  4. Mechanical behavior of lattice structures is important for a range of engineering applications. Herein, a new semiempirical model is proposed that describes the entire range of stress–strain response of lattice structures, including the stress‐instability region which is modeled as an oscillator. The model can be fit to individual stress–strain curves to extract elastic modulus, yield stress, collapse stress, post‐yield collapse ratio, densification strain, and the energy absorbed per unit volume. The model is fit to 119 unique experimental stress–strain curves from 13 research papers in literature covering four different lattice designs, namely, octet truss, body‐centered cubic with vertical members, body‐centered cubic, and hexagonal. Manufacturing methods (additive and conventional) and materials (metals and polymers) were also included in the analysis. The fitted model yields several new insights into the compression behavior of previously tested lattice structures and can be applied to additional lattice designs. Among other results, analysis of variance (ANOVA) reveals that the octet truss lattice demonstrates the highest post‐yield collapse ratio and the smallest normalized energy absorption per unit volume amongst the lattice structures investigated. The proposed model is a powerful tool for designers to quantitatively compare and select 3D lattice structures with the desired mechanical characteristics.

     
    more » « less
  5. Abstract

    Infrared (IR) thermography is a non-contact method of measuring temperature that analyzes the infrared radiation emitted by an object. Properties of polymer composites are heavily influenced by the filler material, filler size, and filler dispersion, and thus thermographic analysis can be a useful tool to determine the curing and filler dispersion. In this study, we investigated the curing mechanisms of polymer composites at the microscale by capturing real-time temperature using an IR Thermal Camera. Silicone polymers with fillers of Graphene, Graphite powder, Graphite flake, and Molybdenum disulfide (MoS2) were subsequently poured into a customized 3D printed mold for thermography. The nanocomposites were microscopically heated with a Nichrome resistance wire, and real-time surface temperatures were measured using different Softwares. This infrared thermal camera divides the target area into 640 × 480 pixels, allowing measurement and analysis of the sample with a resolution of 65 micrometers. Depending on the filler material, the temperature rises to a certain maximum point before curing, and once curing is complete, polymer composites exhibit a rapid temperature change indicating a transition from viscous fluid to solid. MoS2, Polydimethylsiloxane (PDMS) without filler, and PDMS with larger filler are ranked in order of maximum constant temperature. PDMS (without filler) cures in 500s, while PDMS-Graphene and PDMS Graphite Powder cure in about 800s. The curing time for PDMS Graphite flake is slightly longer (950s), while MoS2 is around 520s. Therefore, this technique can indicate the influence of fillers on the curing of composites at the microscale, which is difficult to achieve by conventional methods such as differential scanning calorimetry. This nondestructive, low-cost, fast infrared thermography can be used to analyze the properties of polymer composites with different fillers and dispersion qualities in a variety of applications including precision additive manufacturing and quality control of curable composite inks.

     
    more » « less