AC-poling of Pb(In1/2Nb1/2)O3-Pb(Mg1/3Nb2/3)O3-PbTiO3(PIN-PMN-PT) single crystals with a thickness of 0.06–0.16 mm was studied in this paper. Compared with DC-poled samples, enhancements in piezoelectric and dielectric properties can be obtained when the thickness is above 0.1 mm. However, inconsistency in poling effects was found in the crystals with thickness below 0.1 mm. To elucidate why such scaling effect arises, surface roughness was measured by an atomic force microscopy to correlate surface morphology and poling effects. It was found that non-uniform surface roughness led to inconsistent and decreased properties. Furthermore, temperature-dependent dielectric permittivity spectra were measured to explore how crystal thickness affects the thermal stability of ferroelectric phases. It is noted that complex changes in crystallographic symmetries emanate by decreasing thickness. Such phenomena can be attributed to more influential effects of surface morphology when thickness is reduced. We hope this work suggests a clue for solving the scaling effects of AC-poling on relaxor-PbTiO3single crystals.
Acting like thermal resistances, ferroelectric domain walls can be manipulated to realize dynamic modulation of thermal conductivity (
- Award ID(s):
- 2011978
- NSF-PAR ID:
- 10409652
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Advanced Materials
- Volume:
- 35
- Issue:
- 22
- ISSN:
- 0935-9648
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
-
more » « less
Abstract Piezoelectric materials should simultaneously possess the soft properties (high piezoelectric coefficient,
d 33; high voltage coefficient,g 33; high electromechanical coupling factor,k ) and hard properties (high mechanical quality factor,Q m; low dielectric loss, tan δ) along with wide operation temperature (e.g., high rhombohedral–tetragonal phase transition temperatureT r–t) for covering off‐resonance (figure of merit (FOM),d 33 ×g 33) and on‐resonance (FOM,Q m ×k 2) applications. However, achieving hard and soft piezoelectric properties simultaneously along with high transition temperature is quite challenging since these properties are inversely related to each other. Here, through a synergistic design strategy of combining composition/phase selection, crystallographic texturing, defect engineering, and water quenching technique, <001> textured 2 mol% MnO2doped 0.19PIN‐0.445PSN‐0.365PT ceramics exhibiting giant FOM values ofQ m × (227–261) along with highd 33 ×g 33(28–35 × 10−12m2N−1), low tan δ (0.3–0.39%) and highT r–tof 140–190 °C, which is far beyond the performance of the state‐of‐the‐art piezoelectric materials, are fabricated. Further, a novel water quenching (WQ) room temperature poling technique, which results in enhanced piezoelectricity of textured MnO2doped PIN‐PSN‐PT ceramics, is reported. Based upon the experiments and phase‐field modeling, the enhanced piezoelectricity is explained in terms of the quenching‐induced rhombohedral phase formation. These findings will have tremendous impact on development of high performance off‐resonance and on‐resonance piezoelectric devices with high stability. -
more » « less
Abstract Herein, the experimental observation of micrometer‐scale magnetic skyrmions at room temperature in several Pt/Co‐based thin film heterostructures designed to possess low exchange stiffness, perpendicular magnetic anisotropy, and a modest interfacial Dzyaloshinskii–Moriya interaction (iDMI) is reported. It is found both experimentally and by micromagnetic and analytic modeling that a low exchange stiffness and modest iDMI eliminates the energetic penalty associated with forming domain walls in thin films. When the domain wall energy density approaches negative values, the remanent morphology transitions from a uniform state to labyrinthine stripes. A low exchange stiffness, indicated by a sub‐400 K Curie temperature, is achieved in Pt/Co, Pt/Co/Ni, and Pt/Co/Ni/Re structures by reducing the Co thickness to the ultrathin limit (<0.3 nm). Similar effects occur in thicker Pt/Co/Ni
x Cu1−x structures when the Ni layer is alloyed with Cu. At this transition in domain morphology, skyrmion phases are stabilized by small (<1 mT), perpendicular magnetic fields, and skyrmion motion in response to spin–orbit torque is observed. While the temperature and thickness‐induced morphological phase transitions observed are similar to the well‐studied spin reorientation transition that occurs in the ultrathin limit, the underlying energy balances are substantially modified by the presence of an iDMI. -
more » « less
Abstract Electric‐field‐controlled magnetism is of importance in realizing energy efficient, dense and fast information storage and processing. Strain‐mediated converse magneto‐electric (ME) coupling between ferromagnetic and ferroelectric heterostructure shows promise for realizing electric‐controlled magnetism at room temperature and is attracting a number of recent investigations. However, such ME‐effect studies have mainly focus on magnetic metals. In this work, high quality yttrium iron garnet (Y3Fe5O12(YIG)) films are deposited directly onto (100)‐oriented single‐crystal Pb (Mg1/3Nb2/3)0.7Ti0.3O3(PMN‐PT) substrates by means of magnetron sputtering. The electric‐field‐induced polarization switching and lattice strain in the PMN‐PT substrate results in two distinct magnetization states in the YIG film that are nonvolatile and electrically reversible. Because of the direct contact between the YIG and the PMN‐PT substrate, an efficient ME coupling and an almost 90° rotation of the easy axis of the YIG film can be realized. Furthermore, the electric‐field‐controlled hysteresis loop‐like ferromagnetic resonance field shifts and spin pumping signals are observed in Pt/YIG/PMN‐PT heterostructures. Thus, the obstacle is overcome via growing high‐quality YIG thin films directly onto PMN‐PT substrates and an efficient manipulation of magnetism and pure spin current transport by electric field is thereby realized. These findings are instructive for future low‐power magnetic insulator‐based spintronic devices.
-
more » « less
Materials that can be switched between low and high thermal conductivity states would advance the control and conversion of thermal energy. Employing in situ time-domain thermoreflectance (TDTR) and in situ synchrotron X-ray scattering, we report a reversible, light-responsive azobenzene polymer that switches between high (0.35 W m−1K−1) and low thermal conductivity (0.10 W m−1K−1) states. This threefold change in the thermal conductivity is achieved by modulation of chain alignment resulted from the conformational transition between planar (
trans ) and nonplanar (cis ) azobenzene groups under UV and green light illumination. This conformational transition leads to changes in the π-π stacking geometry and drives the crystal-to-liquid transition, which is fully reversible and occurs on a time scale of tens of seconds at room temperature. This result demonstrates an effective control of the thermophysical properties of polymers by modulating interchain π-π networks by light.
