An official website of the United States government
Abstract Establishing the independent tunability of transport and mechanical properties in polymer gels would significantly contribute to their implementation as transdermal drug delivery media, among other things. The work conducted herein uses facile changes in the formulation of physically crosslinked styrenic ABA/AB block copolymer organogels to alter their mechanical properties independently from the mass transport of an internally‐loaded nanocarrier. Such independent tunability is made possible by altering the relative amounts of ABA triblock and AB diblock copolymers while holding total copolymer concentration fixed. Specifically, three series of gels each with a fixed total copolymer concentration (10, 20, or 30 wt%) comprised of varying triblock copolymer concentration are studied. Small angle x‐ray scattering confirms that, at the nanoscale, only gel network connectivity changes within each series, while mechanical and release experiments show that increasing network connectivity leads to significant growth of gel moduli, but little change in nanocarrier release rate.
more »
« less
Nanostructure Scaling in Semi‐Dilute Triblock Copolymer Gels
Abstract There is a considerable body of work that describes the scaling of diblock copolymer micelle dimensions in dilute and semi‐dilute solution based upon block degrees of polymerization and copolymer concentration. However, there is a lack of analogous information for semi‐dilute ABA triblock copolymer gels, which consist of ABA triblock copolymer dissolved in midblock‐selective (B‐selective) solvent. The present study uses small angle X‐ray scattering to extract micelle dimensions for numerous triblock copolymer gels that vary in copolymer identity (and hence block lengths) and copolymer concentration, as well as gels that contain various ratios of two unique triblock copolymers. Analysis of micelle structural data subsequently translates to universal scaling expressions for the micelle core radius –rA≈NA0.53NB−0.14ϕABA0.16whereNAandNBare the endblock and midblock degrees of polymerization, respectively, andϕABAis the volume fraction of triblock copolymer in the gel – and for the intermicelle spacing –lAA≈NA0.09NB0.29ϕABA−0.35. Each scaling expression describes the full collection of experimental data very well. Additionally, these scaling expressions are partially in line with expectations from semi‐dilute diblock copolymer solution theory.
more »
« less
- Award ID(s):
- 1904047
- PAR ID:
- 10419315
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Macromolecular Chemistry and Physics
- Volume:
- 224
- Issue:
- 16
- ISSN:
- 1022-1352
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
ABSTRACT Mechanical properties including the failure behavior of physically assembled gels or physical gels are governed by their network structure. To investigate such behavior, we consider a physical gel system consisting of poly(styrene)‐poly(isoprene)‐poly(styrene)[PS‐PI‐PS] in mineral oil. In these gels, the endblock (PS) molecular weights are not significantly different, whereas, the midblock (PI) molecular weight has been varied such that we can access gels with and without midblock entanglement. Small angle X‐ray scattering data reveals that the gels are composed of collapsed PS aggregates connected by PI chains. The gelation temperature has been found to be a function of the endblock concentration. Tensile tests display stretch‐rate dependent modulus at high strain for the gels with midblock entanglement. Creep failure behavior has also been found to be influenced by the entanglement. Fracture experiments with predefined cracks show that the energy release rate scales linearly with the crack‐tip velocity for all gels considered here. In addition, increase of midblock chain length resulted in higher viscous dissipation leading to a higher energy release rate. The results provide an insight into how midblock entanglement can possibly affect the mechanical properties of physically assembled triblock copolymer gels in a midblock selective solvent. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys.2019,57, 1014–1026more » « less
-
The physical properties of an ABA triblock copolymer-based thermoplastic elastomer, containing a poly(lauryl methacrylate-co-methacrylic acid) midblock and poly(methyl methacrylate) endblocks, were enhanced through neutralization of the methacrylic acid (MAA) repeat units with NaOH to form ionic interactions in the midblock. Rheological properties of the midblock and mechanical properties of the triblock copolymer were investigated as functions of acid (MAA) and ion content. Midblock relaxation times (τ) increased with increasing acid and ion content, however the activation energy extracted from an Arrhenius analysis appeared constant for all acid and ion contents. Meanwhile, the factors of enhancement of the strain at break and tensile strength (as compared to the baseline polymer without ionic interactions or hydrogen bonding) collapsed onto master curves when plotted as functions of log τ, indicating the mechanical behavior of the triblock copolymer could be tuned through varying the relaxation time of the midblock. The tensile strength increased by as much as a factor of 17 times greater than that of the baseline polymer. More moderate enhancements were observed in the strain at break, with the maximum strain at break occurring at intermediate relaxation times. This suggests that midblock chain dynamics are a governing factor for the mechanical property enhancements, due to the effects of the ionic aggregates and chain mobility on stress dissipation under tensile deformation.more » « less
-
Abstract Block copolymer brushes are of great interest due to their rich phase behavior and value‐added properties compared to homopolymer brushes. Traditional synthesis involves grafting‐to and grafting‐from methods. In this work, a recently developed “polymer‐single‐crystal‐assisted‐grafting‐to” method is applied for the preparation of block copolymer brushes on flat glass surfaces. Triblock copolymer poly(ethylene oxide)‐b‐poly(l‐lactide)‐b‐poly(3‐(triethoxysilyl)propyl methacrylate) (PEO‐b‐PLLA‐b‐PTESPMA) is synthesized with PLLA as the brush morphology‐directing component and PTESPMA as the anchoring block. PEO‐b‐PLLA block copolymer brushes are obtained by chemical grafting of the triblock copolymer single crystals onto a glass surface. The tethering point and overall brush pattern are determined by the single crystal morphology. The grafting density is calculated to be ≈0.36 nm−2from the atomic force microscopy results and is consistent with the theoretic calculation based on the PLLA crystalline lattice. This work provides a new strategy to synthesize well‐defined block copolymer brushes.more » « less
-
Herein, we present the direct modification of glucose, an abundant and inexpensive sugar molecule, to produce new sustainable and functional polymers. Glucose-6-acrylate-1,2,3,4-tetraacetate (GATA) has been synthesized and shown to provide a useful glassy component for developing an innovative family of elastomeric and adhesive materials. A series of diblock and triblock copolymers of GATA and n -butyl acrylate (n-BA) were created via Reversible Addition–Fragmentation Chain Transfer (RAFT) polymerization. Initially, poly(GATA)- b -poly(n-BA) copolymers were prepared using 4-cyano-4-[(ethylsulfanylthiocarbonyl)sulfanyl] pentanoic acid (CEP) as a chain transfer agent (CTA). These diblock copolymers demonstrated decomposition temperatures of 275 °C or greater and two glass transition temperatures ( T g ) around −45 °C and 100 °C corresponding to the PnBA and PGATA domains, respectively, as measured by differential scanning calorimetry (DSC). Triblock copolymers of GATA and n-BA, with moderate dispersities ( Đ = 1.15–1.29), were successfully synthesized when S , S -dibenzyl trithiocarbonate (DTC) was employed as the CTA. Poly(GATA)- b -poly(nBA)- b -poly(GATA) copolymers with 14–58 wt% GATA were prepared and demonstrated excellent thermomechanical properties ( T d ≥ 279 °C). Two well-separated glass transitions near the values for homopolymers of n-BA and GATA (∼−45 °C and ∼100 °C, respectively) were measured by DSC. The triblock with 14% GATA exhibited peel adhesion of 2.31 N cm −1 (when mixed with 30 wt% tackifier) that is superior to many commercial pressure sensitive adhesives (PSAs). Use of 3,5-bis(2-dodecylthiocarbonothioylthio-1oxopropoxy)benzoic acid (BTCBA) as the CTA provided a more efficient route to copolymerize GATA and n-BA. Using BTCBA, poly(GATA)- b -poly(nBA)- b -poly(GATA) triblock copolymers containing 12–25 wt% GATA, with very narrow molar mass distributions ( Đ ≤ 1.08), were prepared. The latter series of triblock copolymers showed excellent thermal stability with T d ≥ 275 °C. Only the T g for the PnBA block was observed by DSC (∼−45 °C), however, phase-separation was confirmed by small-angle X-ray scattering (SAXS) for all of these triblock copolymers. The mechanical behavior of the polymers was investigated by tensile experiments and the triblock with 25% GATA content demonstrated moderate elastomeric properties, 573 kPa stress at break and 171% elongation. This study introduces a new family of glucose-based ABA-type copolymers and demonstrates functionality of a glucose-based feedstock for developing green polymeric materials.more » « less
