An official website of the United States government
Abstract BackgroundStalk lodging (the premature breaking of plant stalks or stems prior to harvest) is a persistent agricultural problem that causes billions of dollars in lost yield every year. Three-point bending tests, and rind puncture tests are common biomechanical measurements utilized to investigate crops susceptibility to lodging. However, the effect of testing rate on these biomechanical measurements is not well understood. In general, biological specimens (including plant stems) are well known to exhibit viscoelastic mechanical properties, thus their mechanical response is dependent upon the rate at which they are deflected. However, there is very little information in the literature regarding the effect of testing rate (aka displacement rate) on flexural stiffness, bending strength and rind puncture measurements of plant stems. ResultsFully mature and senesced maize stems and wheat stems were tested in three-point bending at various rates. Maize stems were also subjected to rind penetration tests at various rates. Testing rate had a small effect on flexural stiffness and bending strength calculations obtained from three-point bending tests. Rind puncture measurements exhibited strong rate dependent effects. As puncture rate increased, puncture force decreased. This was unexpected as viscoelastic materials typically show an increase in resistive force when rate is increased. ConclusionsTesting rate influenced three-point bending test results and rind puncture measurements of fully mature and dry plant stems. In green stems these effects are expected to be even larger. When conducting biomechanical tests of plant stems it is important to utilize consistent span lengths and displacement rates within a study. Ideally samples should be tested at a rate similar to what they would experience in-vivo.
more »
« less
The influence of water content on the longitudinal modulus of elasticity of maize stalk pith and rind tissues
Abstract BackgroundModern computational modeling could provide the key to obtaining new insights into the mechanisms of maize stalk failure as well as suggesting new ways to improve stalk strength. However, a complete set of mechanical properties of maize tissues is required to enable computational modeling of maize stems. This study developed two compression test methods for obtaining the longitudinal modulus of elasticity of both rind and pith tissues, assessed the influence of water content on tissue properties, and investigated the relationship between rind modulus and pith modulus. These methods involved uniform 5–7 cm segments of maize stems which were scanned using a flatbed scanner then tested in compression using a universal testing machine in both intact and dissected (rind-only and pith-only) states. ResultsThe modulus of elasticity of pith tissues was highest for fully turgid specimens and decreased as water was removed from the specimens. Water content was negatively correlated with the modulus of elasticity of the rind. Rind and pith tissues were found to be weakly correlated. The median ratio of rind modulus to pith modulus was found to be 17. Of the two methods investigated, the pith-only specimen preparation was found to be simple reliable while the rind-only method was found to be adversely affected by lateral bowing of the specimen. ConclusionsResearchers can use the information in this paper to improve computational models of maize stems in three ways: (1) by incorporating realistic values of the longitudinal modulus of elasticity of pith and rind tissues; (2) by selecting pith and rind properties that match empirically observed ratios; and (3) by incorporating appropriate dependencies between these material properties and water content. From an experimental perspective, the intact/pith-only experimental method outlined in this paper is simpler than previously reported methods and provides reliable estimates of both pith and rind modulus of elasticity values. Further research using this measurement method is recommended to more clearly understand the influence of water content and turgor pressure on tissue properties.
more »
« less
- Award ID(s):
- 2046669
- PAR ID:
- 10427665
- Publisher / Repository:
- Springer Science + Business Media
- Date Published:
- Journal Name:
- Plant Methods
- Volume:
- 19
- Issue:
- 1
- ISSN:
- 1746-4811
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Stalk lodging contributes to significant crop yield losses. Therefore, understanding the biomechanical strength and structural rigidity of grain stalks can contribute to improving stalk lodging resistance in crops. From the structural constituents of the stalk, the rind provides the principal structure, supporting cells against tension and bending loads. In this work, the biomechanical and viscoelastic behavior of the rind from the internodes of two sweet sorghum varieties (Della and REDforGREEN (RG)), grown in two different growing seasons, were evaluated by three-point micro-bending tests using a dynamic mechanical analyzer (DMA). In addition, the chemical composition of rinds and the microfibril angle (MFA) of the cell wall were determined using XRD. The results revealed that the biomechanical behavior of Della varieties was stiffer and more resistant to loads than that of RG varieties. Two features of the rind biomechanical properties, flexural modulus (FM) and flexural strength (FS), showed a significant reduction for RG. Particularly, a reduction in FS of 16–37% and in FM of 22–41% were detected for RG1. Changes in the stalks’ rind biomechanical properties were attributed to cell wall components. Total lignin and glucan/cellulose contents were positively correlated with the FM and FS of the rind. Subsequently, an increase in the two cell wall components drove an increase in stiffness. Furthermore, the MFA of the rind was also found to influence the rind strength.more » « less
-
Abstract Maize stalk lodging is the structural failure of the stalk prior to harvest and is a major problem for maize (corn) producers and plant breeders. To address this problem, it is critical to understand precisely how geometric and material parameters of the maize stalk influence stalk strength. Computational models could be a powerful tool in such investigations, but current methods of creating computational models are costly, time-consuming and, most importantly, do not provide parameterized control of the maize stalk parameters. The purpose of this study was to develop and validate a parameterized 3D model of the maize stalk. The parameterized model provides independent control over all aspects of the maize stalk geometry and material properties. The model accurately captures the shape of actual maize stalks and is predictive of maize stalk stiffness and strength. The model was validated using stochastic sampling of material properties to account for uncertainty in the values and influence of mechanical tissue properties. Results indicated that buckling is influenced by material properties to a greater extent that flexural stiffness. Finally, we demonstrate that this model can be used to create an unlimited number of synthetic stalks from within the parameter space. This model will enable the future implementation of parameter sweep studies, sensitivity analysis and optimization studies, and can be used to create computational models of maize stalks with any desired combination of geometric and material properties.more » « less
-
Context: Stalk lodging causes up to 43 % of yield losses in maize (Zea mays L.) worldwide, significantly worsening food and feed shortages. Stalk lodging resistance is a complex trait specified by several structural, material, and geometric phenotypes. However, the identity, relative contribution, and genetic tractability of these intermediate phenotypes remain unknown. Objective: The study is designed to identify and evaluate plant-, organ-, and tissue-level intermediate phenotypes associated with stalk lodging resistance following standardized phenotyping protocols and to understand the variation and genetic tractability of these intermediate phenotypes. Methods: We examined 16 diverse maize hybrids in two environments to identify and evaluate intermediate phenotypes associated with stalk flexural stiffness, a reliable indicator of stalk lodging resistance, at physiological maturity. Engineering-informed and machine learning models were employed to understand relationships among intermediate phenotypes and stalk flexural stiffness. Results: Stalk flexural stiffness showed significant genetic variation and high heritability (0.64) in the evaluated hybrids. Significant genetic variation and comparable heritability for the cross-sectional moment of inertia and Young’s modulus indicated that geometric and material properties are under tight genetic control and play a combinatorial role in determining stalk lodging resistance. Among the twelve internode-level traits measured on the bottom and the ear internode, most traits exhibited significant genetic variation among hybrids, moderate to high heritability, and considerable effect of genotype × environment interaction. The marginal statistical model based on structural engineering beam theory revealed that 74–80 % of the phenotypic variation for flexural stiffness was explained by accounting for the major diameter, minor diameter, and rind thickness of the stalks. The machine learning model explained a relatively modest proportion (58–62 %) of the variation for flexural stiffness.more » « less
-
Stalk lodging, or failure of the stalk structure, is a serious problem in the production of maize (corn). Addressing this problem requires an understanding of the parameters that influence lodging resistance. Computational modelling is a powerful tool for this purpose, but current modelling methods have limited throughput and do not provide the ability to modify individual geometric features. A parameterised model of the maize stalk has the potential to overcome these limitations. The purposes of this study were to (a) develop a parameterised model of the maize stalk cross-section that could accurately simulate the physical response of multiple loading cases, and (b) use this model to rigorously investigate the relationships between cross-sectional morphology and predictive model accuracy. Principal component analysis was utilised to reveal underlying geometric patterns which were used as parameters in a cross-sectional model. A series of approximated cross-sections was created that represented various levels of geometric fidelity. The true and approximated cross-sections were modelled in axial tension/compression, bending, transverse compression, and torsion. For each loading case, the predictive accuracy of each approximated model was calculated. A sensitivity study was also performed to quantify the influence of individual parameters. The simplest model, an elliptical cross-section consisting of just three parameters: major diameter, minor diameter, and rind thickness, accurately predicted the structural stiffness of all four loading cases. The modelling approach used in this study model can be used to parameterise the maize cross-section to any desired level of geometric fidelity, and could be applied to other plant species.more » « less
