An official website of the United States government
The Zintl compound Eu 2 ZnSb 2 was recently shown to have a promising thermoelectric figure of merit, zT ∼ 1 at 823 K, due to its low lattice thermal conductivity and high electronic mobility. In the current study, we show that further increases to the electronic mobility and simultaneous reductions to the lattice thermal conductivity can be achieved by isovalent alloying with Bi on the Sb site in the Eu 2 ZnSb 2−x Bi x series ( x = 0, 0.25, 1, 2). Upon alloying with Bi, the effective mass decreases and the mobility linearly increases, showing no signs of reduction due to alloy scattering. Analysis of the pair distribution functions obtained from synchrotron X-ray diffraction revealed significant local structural distortions caused by the half-occupied Zn site in this structure type. It is all the more surprising, therefore, to find that Eu 2 ZnBi 2 possesses high electronic mobility (∼100 cm 2 V −1 s −1 ) comparable to that of AM 2 X 2 Zintl compounds. The enormous degree of disorder in this series gives rise to exceptionally low lattice thermal conductivity, which is further reduced by Bi substitution due to the decreased speed of sound. Increasing the Bi content was also found to decrease the band gap while increasing the carrier concentration by two orders of magnitude. Applying a single parabolic band model suggests that Bi-rich compositions of Eu 2 ZnSb 2−x Bi x have the potential for significantly improved zT ; however, further optimization is necessary through reduction of the carrier concentration to realize high zT .
more »
« less
Investigating the Role of Vacancies on the Thermoelectric Properties of EuCuSb‐Eu 2 ZnSb 2 Alloys
Abstract AMXcompounds with the ZrBeSi structure tolerate a vacancy concentration of up to 50 % on theM‐site in the planarMX‐layers. Here, we investigate the impact of vacancies on the thermal and electronic properties across the full EuCu1−xZn0.5xSb solid solution. The transition from a fully‐occupied honeycomb layer (EuCuSb) to one with a quarter of the atoms missing (EuZn0.5Sb) leads to non‐linear bond expansion in the honeycomb layer, increasing atomic displacement parameters on theMand Sb‐sites, and significant lattice softening. This, combined with a rapid increase in point defect scattering, causes the lattice thermal conductivity to decrease from 3 to 0.5 W mK−1at 300 K. The effect of vacancies on the electronic properties is more nuanced; we see a small increase in effective mass, large increase in band gap, and decrease in carrier concentration. Ultimately, the maximumzTincreases from 0.09 to 0.7 as we go from EuCuSb to EuZn0.5Sb.
more »
« less
- Award ID(s):
- 2045122
- PAR ID:
- 10430966
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Angewandte Chemie International Edition
- Volume:
- 62
- Issue:
- 29
- ISSN:
- 1433-7851
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract We report a theoretical investigation of effects of Mn and Co substitution in the transition metal sites of the kagomé-lattice ferromagnet, Fe3Sn2. Herein, hole- and electron-doping effects of Fe3Sn2have been studied by density-functional theory calculations on the parent phase and on the substituted structural models of Fe3−xMxSn2(M = Mn, Co;x= 0.5, 1.0). All optimized structures favor the ferromagnetic ground state. Analysis of the electronic density of states (DOS) and band structure plots reveals that the hole (electron) doping leads to a progressive decrease (increase) in the magnetic moment per Fe atom and per unit cell overall. The high DOS is retained nearby the Fermi level in the case of both Mn and Co substitutions. The electron doping with Co results in the loss of nodal band degeneracies, while in the case of hole doping with Mn emergent nodal band degeneracies and flatbands initially are suppressed in Fe2.5Mn0.5Sn2but re-emerge in Fe2MnSn2. These results provide key insights into potential modifications of intriguing coupling between electronic and spin degrees of freedom observed in Fe3Sn2.more » « less
-
Abstract The preparation of 0.58 Li2S + 0.315 SiS2+ 0.105 LiPO3glass, and the impacts of polysulfide and P1Pdefect structure impurities on the glass transition temperature (Tg), crystallization temperature (Tc), working range (ΔT≡ Tc‐ Tg), fragility index, and the Raman spectra were evaluated using statistical analysis. In this study, 33 samples of this glass composition were synthesized through melt‐quenching. Thermal analysis was conducted to determine the glass transition temperature, crystallization temperature, working range, and fragility index through differential scanning calorimetry. The quantity of the impurities described above was determined through Raman spectroscopy peak analysis. Elemental sulfur was doped into a glass to quantify the wt% sulfur content in the glasses. Linear regression analysis was conducted to determine the impact of polysulfide impurities and P1Pdefect impurities on the thermal properties. Polysulfide impurities were found to decrease theTgat rate of nearly 12°C per 1 wt% increase in sulfur concentration. The sulfur concentration does not have a statistically significant impact on the other properties (α = 0.05). The P1Pdefect structure appears to decrease the resistance to crystallization of the glass by measurably decreasing the working range of the glasses, but further study is necessary to fully quantify and determine this.more » « less
-
Thermal and electronic transport properties of A Cr X 2 superionic conductors (A=Cu, Ag and X=S, Se)Abstract Superionic conductors, includingACrX2(A=Ag, Cu; X = S, Se) compounds, have attracted attention due to their low lattice thermal conductivity and high ionic conductivity. These properties are driven by structural characteristics such as anharmonicity, soft bonding, and disorder, which enhance both fast ion transport and thermal resistance. In the present study, we investigate the impact of various factors (e.g.A-site disorder, microstructure, speed of sound and chemical composition) on the thermal conductivity of the compounds CuCrS2, CuCrSe2, AgCrS2and AgCrSe2. The samples were synthesized using solid state reaction, ball milling and subsequent spark plasma sintering, and thermal diffusivity, electrical resistivity, Hall coefficients and Seebeck coefficients were measured as a function of temperature. The selenides were found to behave as degenerate semiconductors, with reasonable thermoelectric figure of merit (up to 0.79 in CuCrSe2), while the sulfides behaved as non-degenerate semiconductors with high electrical resistivity. At room temperature, all samples are in the ordered phase and show low lattice thermal conductivity ranging from 0.60 W m−1-K in AgCrSe2to 1.1 W m−1-K in CuCrSe2. Little reduction in lattice thermal conductivity was observed in the high-temperature phase, despite the increased disorder on the cation site and the onset of superionic conductivity. This suggests that the low lattice thermal conductivity inACrX2compounds is an inherent property of the crystal structure, caused by anharmonic bonding and diffuson dominated transport.more » « less
-
Abstract A new compound NaCd4Sb3(Rm,a=4.7013(1) Å,c=35.325(1), Å, Z=3,T=100 K) featuring the RbCd4As3structure type has been discovered in the Na−Cd−Sb system, in addition to the previously reported NaCdSb phase. NaCd4Sb3and NaCdSb were herein synthesized using sodium hydride as the source of sodium. The hydride method allows for targeted sample composition, improved precursor mixing, and an overall quicker synthesis time when compared to traditional methods using Na metal as a precursor. The NaCd4Sb3structure was determined from single‐crystal X‐ray diffraction and contained the splitting of a Cd site not seen in previous isostructural phases. NaCd4Sb3decomposes into NaCdSb plus melt at 766 K, as determined viain‐situhigh‐temperature PXRD. The electronic structure calculations predict the NaCd4Sb3phase to be semi‐metallic, which compliments the measured thermoelectric property data, indicative of ap‐type semi‐metallic material. The crystal structure, elemental analysis, thermal properties, and electronic structure are herein discussed in further detail.more » « less
