skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Lateral load testing and 3D stress measurements in a pile foundation
Embedded sensors within infrastructure elements are powerful catalysts for new designs and construction methods, enabling advanced data collection and informed decision making. This paper presents the development, validation, and implementation of a prototype instrumentation tool utilized in large-scale lateral load tests of rock-socketed pile foundations, with the objective to measure shear stresses near the rock-soil boundary. The proposed instrumentation is novel in that it will be the first attempt to determine experimentally the 3D strain field through embedded sensors with immediate application to a broad array of pile foundation engineering problems. Data obtained from the prototype instrumentation is used to clarify whether shear force amplifications in piles crossing soils with strong stiffness contrasts are real, or an artifact of analytical, Winkler-based design methodologies. Three reinforced concrete pile specimens with a diameter of 0.46 m and a length of 4.9 m were subjected to reverse cyclic lateral loading up to complete structural failure. The sensors’ development, design, and construction, as well as their performance in measuring shear stresses will be discussed by comparing experimental data with predictions from conventional software tools. Ultimately, this study aims to improve the design and construction of more practical, resilient, and economical infrastructure.  more » « less
Award ID(s):
1752303
PAR ID:
10448315
Author(s) / Creator(s):
; ;
Date Published:
Journal Name:
The 11th International Conference on Stress Wave Theory and Design and Testing Methods for Deep Foundations
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; (, IFCEE 2021: Installation, Testing, and Analysis of Deep Foundations)
    El Mohtar, Chadi; Kulesza, Stacey; Baser, Tugce; Venezia, Michael D. (Ed.)
    Piles socketed into rock are frequently utilized to carry large loads from long-span bridges and high-rise buildings into solid ground. The pile design is derived from internal shear and moment magnitudes following code recommendation and numerical predictions. Little experimental data exist to validate code prescriptions and design assumptions for piles embedded in rock. To help alleviate the lack of large-scale test data, the lateral response behavior of three 18-in. diameter, 16 ft long, reinforced concrete piles was evaluated. The pile specimens were embedded in a layer of loose sand and fixed in “rock-sockets,” simulated through high strength concrete. The construction sequence simulated soil-pile interface stress conditions of drilled shafts. The pile reinforcement varied to satisfy the internal reaction forces per (1) code requirements, (2) analytical SSI predictions, and (3) structural demands only. The pile specimens were tested to complete structural failure and excavated thereafter. Internal instrumentation along with crack patterns suggested a combined shear-flexural failure, but do not support the theoretically predicted amplification and de-amplification of shear and moment forces at the boundary, respectively. 
    more » « less
  2. (, DFI Journal The Journal of the Deep Foundations Institute)
    The determination of internal pile reactions is critical to designing and assessing the structural performance of deep foundations. Internal shear and moment profiles strongly depend on lateral pile-soil interaction, which in turn depends on pile and soil stiffnesses as well as the stiffness contrast between soft and stiff strata, such as occurs at a soil/rock interface. At zones of strong geomaterial stiffness contrast, Winkler-spring-type analyses predict abrupt changes in the internal pile reactions for laterally-loaded foundation elements. In particular, the sudden deamplification of internal moments when transitioning from a soft to stiff layer is accompanied by amplification of pile shear. This “shear spike” can result in bulky transverse reinforcement designs for drilled shaft rock sockets that pose constructability challenges due to reinforcement congestion, increasing the risk of defective concrete on the outside of the cage. This paper presents an experimental research program of three large-scale, instrumented drilled shafts with simulated rock sockets constructed from concrete. Each shaft had a different transverse reinforcement design intended to bound the amplitude of the predicted amplified shear demand, with a particular emphasis on performance of shafts with shear resistance less than the predicted demand and below the code minimum. Test results suggested that the shafts experienced a flexure-dominated failure irrespective of the transverse reinforcement detailing. 
    more » « less
  3. ; ; ; ; ; ; (, Groundwater)
    Abstract The design and construction of a waste rock pile influences water infiltration and may promote the production of contaminated mine drainage. The objective of this project is to evaluate the use of an active fiber optic distributed temperature sensing (aFO‐DTS) protocol to measure infiltration and soil moisture within a flow control layer capping an experimental waste rock pile. Five hundred meters of fiber optic cable were installed in a waste rock pile that is 70 m long, 10 m wide, and was covered with 0.60 m of fine compacted sand and 0.25 m of non‐reactive crushed waste rock. Volumetric water content was assessed by heating the fiber optic cable with 15‐min heat pulses at 15 W/m every 30 min. To test the aFO‐DTS system 14 mm of recharge was applied to the top surface of the waste rock pile over 4 h, simulating a major rain event. The average volumetric water content in the FCL increased from 0.10 to 0.24 over the duration of the test. The volumetric water content measured with aFO‐DTS in the FCL and waste rock was within ±0.06 and ±0.03, respectively, compared with values measured using 96 dielectric soil moisture probes over the same time period. Additional results illustrate how water can be confined within the FCL and monitored through an aFO‐DTS protocol serving as a practical means to measure soil moisture at an industrial capacity. 
    more » « less
  4. ; ; ; ; ; ; (, Canadian Geotechnical Journal)
    null (Ed.)
    Recent waste rock pile designs have been proposed to incorporate a fine-grained layer to create a capillary barrier to prevent surface water from draining into the pile interior. This study analyses active fibre optic distributed temperature sensing (FO-DTS) as a tool to measure the effectiveness a capillary barrier system following an infiltration test. A laboratory waste rock column was built with anorthosite waste rock overlain by sand. Volumetric water content is calculated during heat cycles lasting 15 min powered at 15 W/m in the column. A new algorithm is employed to circumvent several requirements for soil specific calibration. The inferred moisture contents were verified by soil moisture probes located adjacent to the cable. The FO-DTS data indicate, at vertical resolutions up to 2 cm, that water is retained in the sand and does not drain into the anorthosite following the infiltration test. The coefficient of determination, R 2 , between the inferred and measured volumetric water content in the fine cover sand layer is 0.90, while the screened anorthosite maintained an R 2 of 0.94 with constant moisture content throughout the test. This study will ultimately help guide future waste rock storage design initiatives incorporating fibre optic sensors, leading to improved environmental mine waste management. 
    more » « less
  5. ; ; (, 53rd U.S. Rock Mechanics/Geomechanics Symposium)
    contain conspicuous acknowledgement of where and by whom the paper was presented. ABSTRACT: Shear strength along discontinuities plays a crucial role in the stability of rock structures. The development of geophysical methods to remotely monitor and assess changes in shear strength is essential to the identification of rock hazards that can lead to the loss of life and failure of civilian infrastructure. In this study, compressional and shear ultrasonic waves were used to monitor slip along discontinuities (with different surface profiles) during shearing. A series of laboratory direct shear experiments were performed on two gypsum blocks separated by a frictional discontinuity. The gypsum blocks had perfectly matched contact surfaces with a half-cycle sine wave profile that spanned the central third of the discontinuity, surrounded by planar surfaces. The amplitude of the half-cycle sine wave was varied and ranged between 2 to 10 times the height of the asperities. Compressional, P, and shear, S, ultrasonic waves were continuously transmitted and recorded throughout the shearing process, while Digital Image Correlation (DIC) was used to capture surface displacements. At low normal stresses, distinct maxima in the normalized P and S wave transmitted amplitudes occurred before shear failure in regions where dilation was observed. Where dilation was not detected, an increase in transmitted wave amplitude was observed, even after the peak shear stress was achieved. At high normal stresses, dilation was suppressed, which was associated with an increase in wave amplitude with shear stress until the peak, and then a decrease in amplitude. Monitoring changes in transmitted wave amplitude is a potential method for the detection of dilation along rock discontinuities. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email