skip to main content

Attention:

The NSF Public Access Repository (PAR) system and access will be unavailable from 11:00 PM ET on Friday, December 13 until 2:00 AM ET on Saturday, December 14 due to maintenance. We apologize for the inconvenience.


Title: Melt‐spun poly(lactic acid) fibers modified with soy fillers: Toward environment‐friendly disposable nonwovens
ABSTRACT

Poly(lactic acid) (PLA) has a significant potential as a biodegradable polymer, but its high cost and slow biodegradability restrict its use in disposable products. This study establishes a novel route to accomplish both objectives by the addition of low‐cost soy fillers into PLA, which reduced material cost and increased the degradation rate of resulting soy‐PLA fibers. Due to partial thermal degradation of soy fillers at PLA melt temperature, they could be melt‐compounded into PLA up to 5 wt%. Fine continuous fibers (D ∼ 25‐50 μm) were successfully produced via melt spinning, and further melt‐consolidated into prototypical nonwovens. The tensile strength of soy‐PLA fibers containing soy reside and soy flour were 56 ± 9 and 44 ± 5 MPa, respectively. Although slightly lower than that of neat PLA fibers (74 ± 2 MPa), the fibers possessed adequate tenacity for use as nonwoven fabrics. Fiber modulus remained unaffected at about 2.5 GPa. The soy‐PLA fibers displayed a relatively rough exterior surface and provided a natural‐fiber feel. The overall degradation of soy‐PLA fibers was accelerated about 2‐fold in a basic medium due to the preferential dissolution of soy that led to increased surface area within the PLA matrix indicating their potential for use in biodegradable nonwovens.

 
more » « less
PAR ID:
10456510
Author(s) / Creator(s):
 ;  ;  ;  
Publisher / Repository:
Wiley Blackwell (John Wiley & Sons)
Date Published:
Journal Name:
Polymer Engineering & Science
Volume:
60
Issue:
6
ISSN:
0032-3888
Page Range / eLocation ID:
p. 1158-1168
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. Abstract

    Electrospinning is commonly used for fabrication of polymer fibers. Melt electrospinning, instead of the commonly used solution electrospinning, offers many advantages in generating polymer fibers without using solvents. However, polymer melts have high viscosity which poses major limitations in producing low diameter fibers. Here, melt electrospinning is investigated at elevated temperatures in inert atmosphere to reduce fiber diameters while suppressing thermal degradation. Two types of spinneret configurations, syringe and wire, with two distinct outcomes are studied. In syringe‐based electrospinning, increasing the nozzle temperature from 300 to 360 °C in nitrogen reduced fiber diameter significantly from 33 ± 5 to 10 ± 4 µm. Electrospinning in nitrogen leads to formation of fibers even at a high nozzle temperature of 360 °C, while this temperature leads to thermal degradation when spinning in air. In contrast, increasing the temperature of wire electrospinning setup do not lead to a noticeable reduction in diameter. This is attributed to the viscosity‐dependent flow rate in this method. Increasing the temperature leads to increased flow rates, promoting the formation of thicker fibers, while the increased stretchability promotes the formation of thinner fibers. The results clearly demonstrate advantages of developing polymer microfibers in inert atmosphere to avoid thermal degradation with a temperature‐independent flow control.

     
    more » « less
  2. Abstract

    Coupling photocatalyst-coated optical fibers (P-OFs) with LEDs shows potential in environmental applications. Here we report a strategy to maximize P-OF light usage and quantify interactions between two forms of light energy (refracted light and evanescent waves) and surface-coated photocatalysts. Different TiO2-coated quartz optical fibers (TiO2-QOFs) are synthesized and characterized. An energy balance model is then developed by correlating different nano-size TiO2coating structures with light propagation modes in TiO2-QOFs. By reducing TiO2patchiness on optical fibers to 0.034 cm2/cm2and increasing the average interspace distance between fiber surfaces and TiO2coating layers to 114.3 nm, refraction is largely reduced when light is launched into TiO2-QOFs, and 91% of light propagated on the fiber surface is evanescent waves. 24% of the generated evanescent waves are not absorbed by nano-TiO2and returned to optical fibers, thus increasing the quantum yield during degradation of a refractory pollutant (carbamazepine) in water by 32%. Our model also predicts that extending the TiO2-QOF length could fully use the returned light to double the carbamazepine degradation and quantum yield. Therefore, maximizing evanescent waves to activate photocatalysts by controlling photocatalyst coating structures emerges as an effective strategy to improve light usage in photocatalysis.

     
    more » « less
  3. Lignin, while economically and environmentally beneficial, has had limited success in use in reinforcing carbon fibers due to harmful chemicals used in biomass pretreatment along with the limited physical interactions between lignin and polyacrylonitrile (PAN) during the spinning process. The focus of this study is to use lignin obtained from chemical-free oxidative biomass pretreatment (WEx) for blending with PAN at melt spinning conditions to produce carbon fiber precursors. In this study, the dynamic rheology of blending PAN with biorefinery lignin obtained from the WEx process is investigated with the addition of 1-butyl-3-methylimidazolium chloride as a plasticizer to address the current barriers of developing PAN/lignin carbon fiber precursors in the melt-spinning process. Lignin was esterified using butyric anhydride to reduce its hydrophilicity and to enhance its interactions with PAN. The studies indicate that butyration of the lignin (BL) increased non-Newtonian behavior and decreased thermo-reversibility of blends. The slope of the Han plot was found to be around 1.47 for PAN at 150 °C and decreased with increasing lignin concentrations as well as temperature. However, these blends were found to have higher elasticity and solution yield stress (47.6 Pa at 20%wt BL and 190 °C) when compared to pure PAN (5.8 Pa at 190 °C). The results from this study are significant for understanding lignin–PAN interactions during melt spinning for lower-cost carbon fibers. 
    more » « less
  4. Cellulose-based conductive composite fibers hold great promise in smart wearable applications, given cellulose's desirable properties for textiles. Blending conductive fillers with cellulose is the most common means of fiber production. Incorporating a high content of conductive fillers is demanded to achieve desirable conductivity. However, a high filler load deteriorates the processability and mechanical properties of the fibers. Here, developing wet-spun cellulose-based fibers with a unique side-by-side (SBS) structure via sustainable processing is reported. Sustainable sources (cotton linter and post-consumer cotton waste) and a biocompatible intrinsically conductive polymer (i.e., polyaniline, PANI) were engineered into fibers containing two co-continuous phases arranged side-by-side. One phase was neat cellulose serving as the substrate and providing good mechanical properties; another phase was a PANI-rich cellulose blend (50 wt%) affording electrical conductivity. Additionally, an eco-friendly LiOH/urea solvent system was adopted for the fiber spinning process. With the proper control of processing parameters, the SBS fibers demonstrated high conductivity and improved mechanical properties compared to single-phase cellulose and PANI blended fibers. The SBS fibers demonstrated great potential for wearable e-textile applications. 
    more » « less
  5. The development of macroscopic aerogels from 1D systems, such as nanofibers, has resulted in a novel pathway to obtain porous and lightweight architectures. In this work, bright green, red, and tunable color emitting aerogels were obtained with luminescent nanofibers as the precursor system. A simple, low cost, and environmentally friendly process is followed where luminescent fillers are encapsulated within fibers which were subsequently freeze-dried to form 3D aerogels and sponge-like structures. Moreover, the aerogels/sponge-like structures show higher photoluminescence intensity than the fiber mats due to an increase of porosity which provides higher and direct interaction with the fillers and therefore an efficient light absorption resulting in higher luminescence. Manganese doped zinc germanate (Mn: Zn 2 GeO 4 ) nanorods and chromium doped zinc gallate (Cr: ZnGa 2 O 4 ) nanoparticles were used as the source of green and red emissions respectively. By precisely adjusting the stoichiometric ratios of nanorods and nanoparticles within the nanofibers, a broad spectrum output is obtained from the final aerogels. We foresee that these types of photoluminescent aerogels have promising potential applications in a variety of fields such as display devices, solid-state lighting, sensors, etc. 
    more » « less