skip to main content


Title: UAV wildlife radiotelemetry: System and methods of localization
Abstract

The majority of bird and bat species are incapable of carrying tags that transmit their position to satellites. Given fundamental power requirements for such communication, burdened mass guidelines and battery technology, this constraint necessitates the continued use of very high frequency (VHF) radio beacons. As such, efforts should be made to mitigate their primary deficiencies: detection range, localization time and localization accuracy.

The integration of a radiotelemetry system with an unmanned aerial vehicle (UAV) could significantly improve the capacity for data collection from VHF tags. We present a UAV‐integrated radiotelemetry system that relies on open source hardware and software. Localization methods, including signal processing, bearing estimation based on principal component analysis, localization techniques and test results, are discussed.

Using a low‐power beacon applicable for bats and small birds, testing showed that the improved vantage of the UAV‐radiotelemetry system (UAV‐RT) provided significantly higher received signal power compared to the low‐level flights (maximum range beyond 1.4 km). Flight testing of localization methods showed median bearing errors between 2.3° and 6.8°, with localization errors of between 5% and 14% of the distance to the tag. In a direct comparison to an experienced radiotelemetry user, the UAV‐RT system provided bearing and localization estimates with 53% less error.

This paper introduces the core functionality and use methods of the UAV‐RT system, while presenting baseline localization performance metrics. An associated website hosts plans for assembly and software installation. The methods of UAV‐RT use for tag detection will be further developed in future works. For both the detection and localization problems, the mobility of a flying asset drastically reduces tracker time requirements. A 7‐min flight would be sufficient to collect five equally spaced bearing estimates over a 1‐km transect. The use of a software‐defined radio on the UAV‐RT system will allow for the simultaneous detection and localization of multiple tags.

 
more » « less
NSF-PAR ID:
10460566
Author(s) / Creator(s):
 ;  ;  ;  ;
Publisher / Repository:
Wiley-Blackwell
Date Published:
Journal Name:
Methods in Ecology and Evolution
Volume:
10
Issue:
10
ISSN:
2041-210X
Page Range / eLocation ID:
p. 1783-1795
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. Abstract Background

    Rapid improvements in inexpensive, low-power, movement and environmental sensors have sparked a revolution in animal behavior research by enabling the creation of data loggers (henceforth, tags) that can capture fine-grained behavioral data over many months. Nevertheless, development of tags that are suitable for use with small species, for example, birds under 25 g, remains challenging because of the extreme mass (under 1$$\textrm{g}$$g) and power (average current under 1$$\upmu$$μA) constraints. These constraints dictate that a tag should carry exactly the sensors required for a given experiment and the data collection protocol should be specialized to the experiment. Furthermore, it can be extremely challenging to design hardware and software to achieve the energy efficiency required for long tag life.

    Results

    We present an activity monitor, BitTag, that can continuously collect activity data for 4–12 months at 0.5–0.8$$\textrm{g}$$g, depending upon battery choice, and which has been used to collect more than 500,000 h of data in a variety of experiments. The BitTag architecture provides a general platform to support the development and deployment of custom sub-$$\textrm{g}$$gtags. This platform consists of a flexible tag architecture, software for both tags and host computers, and hardware to provide the host/tag interface necessary for preparing tags for “flight” and for accessing tag data “post-flight”. We demonstrate how the BitTag platform can be extended to quickly develop novel tags with other sensors while satisfying the 1g/1$$\upmu$$μA mass and power requirements through the design of a novel barometric pressure sensing tag that can collect pressure and temperature data every 60$$\textrm{s}$$sfor a year with mass under 0.6$$\textrm{g}$$g.

     
    more » « less
  2. There is much interest in fine-grained RFID localization systems. Existing systems for accurate localization typically require infrastructure, either in the form of extensive reference tags or many antennas (e.g., antenna arrays) to localize RFID tags within their radio range. Yet, there remains a need for fine-grained RFID localization solutions that are in a compact, portable, mobile form, that can be held by users as they walk around areas to map them, such as in retail stores, warehouses, or manufacturing plants. We present the design, implementation, and evaluation of POLAR, a portable handheld system for fine-grained RFID localization. Our design introduces two key innovations that enable robust, accurate, and real-time localization of RFID tags. The first is complex-controlled polarization (CCP), a mechanism for localizing RFIDs at all orientations through software-controlled polarization of two linearly polarized antennas. The second is joint tag discovery and localization (JTDL), a method for simultaneously localizing and reading tags with zero-overhead regardless of tag orientation. Building on these two techniques, we develop an end-to-end handheld system that addresses a number of practical challenges in self-interference, efficient inventorying, and self-localization. Our evaluation demonstrates that POLAR achieves a median accuracy of a few centimeters in each of the x/y/z dimensions in practical indoor environments. 
    more » « less
  3. This demo presents RFind, a system that enables fine-grained RFID localization via ultra-wideband emulation. RFind operates by measuring the time-of-flight -- i.e., the time it takes the signal to travel from an antenna to an RFID tag. To do so, it emulates an ultra-wide bandwidth on today's narrowband RFIDs without requiring any hardware modification to the tags. It then uses the large emulated bandwidth to estimate the time-of-flight and localize RFIDs. In contrast to past RFID localization proposals, RFind can operate in multipath-rich environments without reference tags and without requiring tag or antenna motion. The demo will allow users to move RFID-tagged objects to any location in line-of-sight, non-line-of-sight, and multi-path rich settings and check that the system can accurately localize the objects. 
    more » « less
  4. The food and drug industry is facing the need to monitor the quality and safety of their products. This has made them turn to low-cost solutions that can enable smart sensing and tracking without adding much overhead. One such popular low-power solution is backscatter-based sensing and communication system. While it offers the promise of battery-less tags, it does so at the cost of a reduced communication range. In this work, we propose PACT - a scalable communication system that leverages the knowledge asymmetry in the network to improve the communication range of the tags. Borrowing from the backscatter principles, we design custom PACT Tags that are battery-less but use an active radio to extend the communication range beyond standard passive tags. They operate using the energy harvested from the PACT Source. A wide-band Reader is used to receive multiple Tag responses concurrently and upload them to a cloud server, enabling real-time monitoring and tracking at a longer range. We identify and address the challenges in the practical design of battery-less PACT Tags using an active radio and prototype them using off-the-shelf components. We show experimentally that our Tag consumes only 23μJ energy, which is harvested from an excitation Source that is up to 24 meters away from the Tag. We show that in outdoor deployments, the responses from an estimated 520 Tags can be received by a Reader concurrently while being 400 meters away from the Tags.

     
    more » « less
  5. Abstract

    The use of technology in field ecology is increasing rapidly and many applications require that equipment operates autonomously for weeks, months or even years. While reducing power requirements can extend the battery life of many field devices, research time frames are always limited without renewable power. However, commercially available units that provide autonomous solar power are either prohibitively expensive or too small to sustain continuous operation for many field devices.

    We describe a semi‐portable, field deployable solar unit that can provide sustainable power for a wide variety of field devices, including passive acoustic recorders, motion‐activated cameras, speakers and microcomputers. Depending on power needs, these units can be built in‐house for only a few hundred dollars (USD) with minimal access to tools or shop facilities. Further, we provide information on how to calculate power requirements and modify the system design to accommodate user needs.

    We have used these units effectively in the field for six research seasons, with continuous autonomous operation varying between 2 weeks and 8 months. Batteries and other parts are easily accessed and replaced if needed.

    Our example system can be modified to provide different output voltage (e.g. 12, 5 V), or to power audio speakers. We also describe a switch that can be placed within the unit to regulate power production to certain times of the day or week. Our aim is to facilitate the use of electronics in the field for ecologists who may lack funding, time or the expertise to design a system independently.

     
    more » « less