Mechanical properties including the failure behavior of physically assembled gels or physical gels are governed by their network structure. To investigate such behavior, we consider a physical gel system consisting of poly(styrene)‐poly(isoprene)‐poly(styrene)[PS‐PI‐PS] in mineral oil. In these gels, the endblock (PS) molecular weights are not significantly different, whereas, the midblock (PI) molecular weight has been varied such that we can access gels with and without midblock entanglement. Small angle X‐ray scattering data reveals that the gels are composed of collapsed PS aggregates connected by PI chains. The gelation temperature has been found to be a function of the endblock concentration. Tensile tests display stretch‐rate dependent modulus at high strain for the gels with midblock entanglement. Creep failure behavior has also been found to be influenced by the entanglement. Fracture experiments with predefined cracks show that the energy release rate scales linearly with the crack‐tip velocity for all gels considered here. In addition, increase of midblock chain length resulted in higher viscous dissipation leading to a higher energy release rate. The results provide an insight into how midblock entanglement can possibly affect the mechanical properties of physically assembled triblock copolymer gels in a midblock selective solvent. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys.
We carried out a large set of tests to establish a correlation between the molecular (network) structure (influenced by molecular weight, molecular weight distribution, and melt predeformation) and mechanical responses of several glassy polymers to uniaxial compression at different temperatures and different compression speeds. The experimental results show that to have ductile responses there must be an adequate chain network, afforded by the interchain uncrossability among sufficiently long chains. Specifically, polystyrene (PS) and poly(methyl methacrylate) of sufficiently low molar mass do not have chain network and are found to be very brittle. Binary PS mixtures are brittle at room temperature when the volume fraction of the high‐molecular‐weight component is sufficiently low (e.g., at and below 27.5%). Moreover, sufficiently melt‐stretched PS mixtures show brittle fracture when compressed along the same direction, along which melt stretching was made. All the experimental findings confirm that a robust chain network is also a prerequisite for yielding and ductile cold compression of polymer glasses, as is for extension. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys.
- PAR ID:
- 10461172
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Journal of Polymer Science Part B: Polymer Physics
- Volume:
- 57
- Issue:
- 12
- ISSN:
- 0887-6266
- Page Range / eLocation ID:
- p. 758-770
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
ABSTRACT 2019 ,57 , 1014–1026 -
more » « less
ABSTRACT The physical aging behavior, time‐dependent densification, of thin polystyrene (PS) films supported on silicon are investigated using ellipsometry for a large range of molecular weights (MWs) from
M w = 97 to 10,100 kg mol−1. We report an unexpected MW dependence to the physical aging rate ofh < 80‐nm thick films not present in bulk films, where samples made from ultra‐high MWs ≥ 6500 kg mol−1exhibit on average a 45% faster aging response at an aging temperature of 40 °C compared with equivalent films made from (merely) high MWs ≤ 3500 kg mol−1. This MW‐dependent difference in physical aging response indicates that the breadth of the gradient in dynamics originating from the free surface in these thin films is diminished for films of ultra‐high MW PS. In contrast, measures of the film‐average glass transition temperatureT g (h ) and effective average film density (molecular packing) show no corresponding change for the same range of film thicknesses, suggesting physical aging may be more sensitive to differences in dynamical gradients. These results contribute to growing literature reports signaling that chain connectivity and entropy play a subtle, but important role in how glassy dynamics are propagated from interfaces. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys.2019 ,57 , 1224–1238 -
more » « less
ABSTRACT This article reports a chain‐growth coupling polymerization of AB difunctional monomer via copper‐catalyzed azide–alkyne cycloaddition (CuAAC) reaction for synthesis of star polymers. Unlike our previously reported CuAAC polymerization of AB
n (n ≥ 2) monomers that spontaneously demonstrated a chain‐growth mechanism in synthesis of hyperbranched polymer, the homopolymerization of AB monomer showed a common but less desired step‐growth mechanism as the triazole groups aligned in a linear chain could not effectively confine the Cu catalyst in the polymer species. In contrast, the use of polytriazole‐based core molecules that contained multiple azido groups successfully switched the polymerization of AB monomers into chain‐growth mechanism and produced 3‐arm star polymers and multi‐arm hyperstar polymers with linear increase of polymer molecular weight with conversion and narrow molecular weight distribution, for example,M w/M n ~ 1.05. When acid‐degradable hyperbranched polymeric core was used, the obtained hyperstar polymers could be easily degraded under acidic environment, producing linear degraded arms with defined polydispersity. © 2019 Wiley Periodicals, Inc. J. Polym. Sci.2020 ,58 , 84–90 -
more » « less
ABSTRACT Ternary block copolymer (BCP)‐homopolymer (HP) blends offer a simple method for tuning nanostructure sizes to meet application‐specific demands. Comprehensive dissipative particle dynamic (DPD) simulations were performed to study the impact of polymer interactions, molecular weight, and HP volume fraction (
φ HPφ HPα =N HP/N BCPφ HPα α 2019 ,57 , 794–803 -
more » « less
ABSTRACT The ever‐growing catalog of monomers being incorporated into block polymers affords exceptional control over phase behavior and nanoscale structure. The segregation strength, χ
N , is the fundamental link between the molecular‐level detail and the thermodynamics. However, predicting phase behavior mandates at least one experimental measurement of χN for each pair of blocks. This typically requires access to the disordered state. We describe a method for estimating χN from small‐angle X‐ray scattering measurements of the interfacial width between lamellar microdomains,t x , in the microphase‐separated melt. The segregation strength is determined by comparingt x to self‐consistent field theory calculations of the intrinsic interfacial width,t i , as a function of the mean‐field χN . The method is validated using a series of independent experimental measurements oft x and χN , measured via the order–disorder transition temperature,T ODT. The average absolute relative difference between χN calculated fromt x and the value calculated fromT ODTis a modest 11%. Corrections for nonplanarity of the interfaces are investigated but do not improve the agreement between the experiments and theory. Published 2019. This article is a U.S. Government work and is in the public domain in the USA. J. Polym. Sci., Part B: Polym. Phys. 2019 © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys.2019 ,57 , 932–940
