We recorded a MWR3.6 earthquake in Idaho (USA) on 7 April 2020 with a network of six three‐element infrasound arrays and co‐located broadband seismometers situated within 25 km of the hypocenter. Infrasound array processing is used to identify the arrival of seismic‐to‐atmospheric coupled phases and as much as 90 s of infrasound coda. Apparent velocities ranging from seismic speeds to subhorizontal atmospheric sound speeds are attributed to a superposition of coincident waves arriving at the arrays. We find that the arriving infrasound originates from a broad range of back azimuths that deviates from epicentral back azimuth and indicates the ubiquity of secondary radiators for this relatively small earthquake. Secondary radiators, which often locate in regions of elevated topography, are identified using backprojections and earthquake initiation time. Analysis of infrasound sources from proximal earthquakes can be used to map ground shaking distributions, which are important for assessment of earthquake hazards.
Seismic ground motion creates low-frequency atmospheric sound (infrasound) that is detectable at remote sensor arrays. However, earthquake infrasound signal analysis is complicated by interference between multiple waves arriving at sensors simultaneously, reducing the accuracy and detail of ground motion detection. Here we show that individual waves in complicated wavefields can be resolved by recording infrasound on large-N arrays and processing with CLEAN beamforming. Examining both a local (ML3.5, purely tropospheric infrasound propagation) and regional earthquake (ML6.5, upper-atmospheric returns), we detect infrasound from tens of km away and up to several hundred km away respectively. Source regions span arcs of approximately 90°, indicating that although detection bias does occur (most likely from atmospheric winds) the recorded infrasound sources are widely dispersed and not simply epicentral. Infrasound-based remote detection of ground motion over wide areas can complement point measurements by seismometers and spur innovations in earthquake research and real-time hazard monitoring.
more » « less- NSF-PAR ID:
- 10471967
- Publisher / Repository:
- Nature Publishing Group
- Date Published:
- Journal Name:
- Communications Earth & Environment
- Volume:
- 4
- Issue:
- 1
- ISSN:
- 2662-4435
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
Abstract -
more » « less
Abstract Ambient infrasound noise contains an abundance of information that is typically overlooked due to limitations of typical infrasound arrays. To evaluate the ability of large‐N infrasound arrays to identify weak signals hidden in background noise, we examine data from a 22‐element array in central Idaho, USA, spanning 58 days using a standard beamforming method. Our results include nearly continuous detections of diverse weak signals from infrasonic radiators, sometimes at surprising distances. We observe infrasound from both local (8 km) and distant (195 km) waterfalls. Thunderstorms and earthquakes are also notable sources, with distant thunderstorm infrasound observed from ∼800 to 900 km away. Our findings show that large‐N infrasound arrays can detect very weak signals below instrument and environmental noise floors, including from multiple simultaneous sources, enabling new infrasound monitoring applications and helping map the composition of background noise wavefields.
-
ABSTRACT Earthquakes generate infrasound in multiple ways. Acoustic coupling at the surface from vertical seismic velocity, termed local infrasound, is often recorded by infrasound sensors but has seen relatively little study. Over 140 infrasound stations have recently been deployed in Alaska. Most of these stations have single sensors, rather than arrays, and were originally installed as part of the EarthScope Transportable Array. The single sensor nature, paucity of ground-truth signals, and remoteness makes evaluating their data quality and utility challenging. In addition, despite notable recent advances, infrasound calibration and frequency response evaluation remains challenging, particularly for large networks and retrospective analysis of sensors already installed. Here, we examine local seismoacoustic coupling on colocated seismic and infrasound stations in Alaska. Numerous large earthquakes across the region in recent years generated considerable vertical seismic velocity and local infrasound that were recorded on colocated sensors. We build on previous work and evaluate the full infrasound station frequency response using seismoacoustic coupled waves. By employing targeted signal processing techniques, we show that a single seismometer may be sufficient for characterizing the response of an entire nearby infrasound array. We find that good low frequency (<1 Hz) infrasound station response estimates can be derived from large (Mw>7) earthquakes out to at least 1500 km. High infrasound noise levels at some stations and seismic-wave energy focused at low frequencies limit our response estimates. The response of multiple stations in Alaska is found to differ considerably from their metadata and are related to improper installation and erroneous metadata. Our method provides a robust way to remotely examine infrasound station frequency response and examine seismoacoustic coupling, which is being increasingly used in airborne infrasound observations, earthquake magnitude estimation, and other applications.more » « less
-
Abstract Infrasound may be used to detect the approach of hazardous volcanic mudflows, known as lahars, tens of minutes before their flow fronts arrive. We have analyzed signals from more than 20 secondary lahars caused by precipitation events at Fuego Volcano during Guatemala’s rainy season in May through October of 2022. We are able to quantify the capabilities of infrasound monitoring through comparison with seismic data, time lapse camera imagery, and high-resolution video of a well-recorded event on August 17. We determine that infrasound sensors, deployed adjacent to the lahar path and in small-aperture (10 s of meters) arrays, are particularly sensitive to remote detection of lahars, including small-sized events, at distances of at least 5 km. At Fuego Volcano these detections could be used to provide timely alerts of up to 30 min before lahars arrive at a downstream monitoring site, such as in the frequently impacted Ceniza drainage. We propose that continuous infrasound monitoring, from locations adjacent to a drainage, may complement seismic monitoring and serve as a valuable tool to help identify approaching hazards. On the other hand, infrasound arrays located a kilometer or more from the lahar path can be effectively used to track a lahar’s progression.more » « less
-
more » « less
Abstract We provide high‐resolution seismic imaging of the central Garlock fault using data recorded by two dense seismic arrays that cross the Ridgecrest rupture zone (B4) and the Garlock fault (A5). Analyses of fault zone head waves and
P ‐wave delay times at array A5 show that the Garlock fault is a sharp bimaterial interface withP waves traveling ∼5% faster in the northern crustal block. The across‐fault velocity contrast agrees with regional tomography models and generates clearP ‐wave reflections in waveforms recorded by array B4. Kirchhoff migration of the reflected waves indicates a near‐vertical fault between 2 and 6 km depth. TheP ‐wave delay times imply a ∼300‐m‐wide transition zone near the Garlock fault surface trace beneath array A5, offset to the side with faster velocities. The results provide important constraints for derivations of earthquake properties, simulations of ruptures and ground motion, and future imaging studies associated with the Garlock fault.
