An official website of the United States government
Abstract The growing demand for flexible and wearable hybrid electronics has triggered the need for advanced manufacturing techniques with versatile printing capabilities. Complex ink formulations, use of surfactants/contaminants, limited source materials, and the need for high‐temperature heat treatments for sintering are major issues facing the current inkjet and aerosol printing methods. Here, the nanomanufacturing of flexible hybrid electronics (FHE) by dry printing silver and indium tin oxide on flexible substrates using a novel laser‐based additive nanomanufacturing process is reported. The electrical resistance of the printed lines is tailored during the print process by tuning the geometry and structure of the printed samples. Different FHE designs are fabricated and tested to check the performance of the devices. Mechanical reliability tests including cycling, bending, and stretching confirm the expected performance of the printed samples under different strain levels. This transformative liquid‐free process allows the on‐demand formation and in situ laser crystallization of nanoparticles for printing pure materials for future flexible and wearable electronics and sensors.
more »
« less
In-situ tension investigation of additively manufactured silver lines on flexible substrates
The reliability of additively manufactured flexible electronics or so-called printed electronics is defined as mean time to failure under service conditions, which often involve mechanical loads. It is thus important to understand the mechanical behavior of the printed materials under such conditions to ensure their applicational reliability in, for example, sensors, biomedical devices, battery and storage, and flexible hybrid electronics. In this article, a testing protocol to examine the print quality of additively nanomanufactured electronics is presented. The print quality is assessed by both tensile and electrical resistivity responses during in-situ tension tests. A laser based additive nanomanufacturing method is used to print conductive silver lines on polyimide substrates, which is then tested in-situ under tension inside a scanning electron microscope (SEM). The surface morphology of the printed lines is continuously monitored via the SEM until failure. In addition, the real-time electrical resistance variations of the printed silver lines are measured in-situ with a multimeter during tensile tests conducted outside of the SEM. The protocol is shown to be effective in assessing print quality and aiding process tuning. Finally, it is revealed that samples appearing identical under the SEM can have significant different tendencies to delaminate.
more »
« less
- Award ID(s):
- 1923363
- PAR ID:
- 10472632
- Publisher / Repository:
- ScienceDirect
- Date Published:
- Journal Name:
- Additive Manufacturing Letters
- Volume:
- 7
- Issue:
- C
- ISSN:
- 2772-3690
- Page Range / eLocation ID:
- 100171
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Printed electronics are gaining significant interest due to their design flexibility, low fabrication cost, and rapid design-to-manufacturing turnaround. Conventional substrates for printed electronics are often based on nonbiodegradable polymers such as polyimide that pose high environmental challenges by creating massive e-waste and pollution. As the demand for printed electronics and sensors increases, the ability to print such devices on biodegradable substrates can provide a solution to such environmental problems. However, current printing technologies are based on liquids and inks that are incompatible with biodegradable substrates, such as paper. Here, we present a dry-printing process, namely, a dry additive nanomanufacturing (Dry-ANM) technique, for printing conductive silver lines and patterns on biodegradable papers for flexible hybrid papertronics. Pure and dry nanoparticles are generated by pulsed laser ablation of a silver target that is then transported through a nozzle and directed onto paper substrates, where they are deposited and laser-sintered in real time to form the desired pattern without damaging the paper. The effects of different printing parameters on the paper-burning threshold are investigated, and the electrical properties of the lines are characterized by using different line thicknesses and sintering laser power densities. In addition, the mechanical and electrical properties of the printed lines and patterns are evaluated by bending and twisting tests. Furthermore, the feasibility of printing silver on different paper types is demonstrated. This research can potentially lead to biodegradable and environmentally friendly printed electronics and sensors.more » « less
-
Abstract The demand for flexible printed electronics is growing fast, especially with the move toward the Internet of Things (IoT). These printed electrons are usually designed for short-term use, after which they are disposed of. The polymeric substrates used in printed electronics comprise the biggest portion of their non-biodegradable E-waste after their disposal. This paper demonstrates the feasibility of printing fully functional transient electronics on flexible, water-soluble, and biodegradable paper substrates using the dry printing approach. The in-situ generation and real-time sintering of silver nanoparticles at room temperature enables the fabrication of complex circuits on such water-soluble papers. A layout similar to an Arduino pro mini board is printed on both sides of a paper substrate with electrical interconnects. Various electrical components are then directly mounted to fabricate a complete, working paper Arduino circuit. Cyclic bending tests demonstrate the mechanical durability and reliability of printed paper circuits under repeated bending stress. The process uniquely achieves robust and complex printed electronics without thermal damage, and the water solubility tests successfully show rapid dissolution of the paper devices in water. Furthermore, the components detached during dissolution are collected and reused, demonstrating the recyclability of the process. Overall, this transformative manufacturing method establishes key technical capabilities to produce next-generation sustainable, green electronics and sensors using renewable materials.more » « less
-
Additively manufactured electronics (AMEs), also known as printed electronics, are becoming increasingly important for the anticipated Internet of Things (IoT). This requires manufacturing technologies that allow the integration of various pure functional materials and devices onto different flexible and rigid surfaces. However, the current ink-based technologies suffer from complex and expensive ink formulation, ink-associated contaminations (additives/solvents), and limited sources of printing materials. Thus, printing contamination-free and multimaterial structures and devices is challenging. Here, a multimaterial additive nanomanufacturing (M-ANM) technique utilizing directed laser deposition at the nano and microscale is demonstrated, allowing the printing of lateral and vertical hybrid structures and devices. This M-ANM technique involves pulsed laser ablation of solid targets placed on a target carousel inside the printer head for in-situ generation of contamination-free nanoparticles, which are then guided via a carrier gas toward the nozzle and onto the surface of the substrate, where they are sintered and printed in real-time by a second laser. The target carousel brings a particular target in engagement with the ablation laser beam in predetermined sequences to print multiple materials, including metals, semiconductors, and insulators, in a single process. Using this M-ANM technique, various multimaterial devices such as silver/zinc oxide (Ag/ZnO) photodetector and hybrid silver/aluminum oxide (Ag/Al2O3) circuits are printed and characterized. The quality and versatility of our M-ANM technique offer a potential manufacturing option for emerging IoT.more » « less
-
Abstract Van der Waals semiconductors (vdWS) offer superior mechanical and electrical properties and are promising for flexible microelectronics when combined with polymer substrates. However, the self‐passivated vdWS surfaces and their weak adhesion to polymers tend to cause interfacial sliding and wrinkling, and thus, are still challenging the reliability of vdWS‐based flexible devices. Here, an effective covalent vdWS–polymer lamination method with high stretch tolerance and excellent electronic performance is reported. Using molybdenum disulfide (MoS2)and polydimethylsiloxane (PDMS) as a case study, gold–chalcogen bonding and mercapto silane bridges are leveraged. The resulting composite structures exhibit more uniform and stronger interfacial adhesion. This enhanced coupling also enables the observation of a theoretically predicted tension‐induced band structure transition in MoS2. Moreover, no obvious degradation in the devices’ structural and electrical properties is identified after numerous mechanical cycle tests. This high‐quality lamination enhances the reliability of vdWS‐based flexible microelectronics, accelerating their practical applications in biomedical research and consumer electronics.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1016/j.addlet.2023.100171
