skip to main content


This content will become publicly available on November 9, 2024

Title: Aerosol Jet Printing Conductive 3D Microstructures from Graphene Without Post‐Processing
Abstract

Three‐dimensional (3D) graphene microstructures have the potential to boost performance in high‐capacity batteries and ultrasensitive sensors. Numerous techniques have been developed to create such structures; however, the methods typically rely on structural supports, and/or lengthy post‐print processing, increasing cost and complexity. Additive manufacturing techniques, such as printing, show promise in overcoming these challenges. This study employs aerosol jet printing for creating 3D graphene microstructures using water as the only solvent and without any post‐print processing required. The graphene pillars exhibit conductivity immediately after printing, requiring no high‐temperature annealing. Furthermore, these pillars are successfully printed in freestanding configurations at angles below 45° relative to the substrate, showcasing their adaptability for tailored applications. When graphene pillars are added to humidity sensors, the additional surface area does not yield a corresponding increase in sensor performance. However, graphene trusses, which add a parallel conduction path to the sensing surface, are found to improve sensitivity nearly 2×, highlighting the advantages of a topologically suspended circuit construction when adding 3D microstructures to sensing electrodes. Overall, incorporating 3D graphene microstructures to sensor electrodes can provide added sensitivity, and aerosol jet printing is a viable path to realizing these conductive microstructures without any post‐print processing.

 
more » « less
NSF-PAR ID:
10473549
Author(s) / Creator(s):
 ;  ;  ;  ;  ;  ;  
Publisher / Repository:
Wiley Blackwell (John Wiley & Sons)
Date Published:
Journal Name:
Small
ISSN:
1613-6810
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. There has been an increasing need of technologies to manufacturing chemical and biological sensors for various applications ranging from environmental monitoring to human health monitoring. Currently, manufacturing of most chemical and biological sensors relies on a variety of standard microfabrication techniques, such as physical vapor deposition and photolithography, and materials such as metals and semiconductors. Though functional, they are hampered by high cost materials, rigid substrates, and limited surface area. Paper based sensors offer an intriguing alternative that is low cost, mechanically flexible, has the inherent ability to filter and separate analytes, and offers a high surface area, permeable framework advantageous to liquid and vapor sensing. However, a major drawback is that standard microfabrication techniques cannot be used in paper sensor fabrication. To fabricate sensors on paper, low temperature additive techniques must be used, which will require new manufacturing processes and advanced functional materials. In this work, we focus on using aerosol jet printing as a highresolution additive process for the deposition of ink materials to be used in paper-based sensors. This technique can use a wide variety of materials with different viscosities, including materials with high porosity and particles inherent to paper. One area of our efforts involves creating interdigitated microelectrodes on paper in a one-step process using commercially available silver nanoparticle and carbon black based conductive inks. Another area involves use of specialized filter papers as substrates, such as multi-layered fibrous membrane paper consisting of a poly(acrylonitrile) nanofibrous layer and a nonwoven poly(ethylene terephthalate) layer. The poly(acrylonitrile) nanofibrous layer are dense and smooth enough to allow for high resolution aerosol jet printing. With additively fabricated electrodes on the paper, molecularly-functionalized metal nanoparticles are deposited by molecularly-mediated assembling, drop casting, and printing (sensing and electrode materials), allowing full functionalization of the paper, and producing sensor devices with high surface area. These sensors, depending on the electrode configuration, are used for detection of chemical and biological species in vapor phase, such as water vapor and volatile organic compounds, making them applicable to human performance monitoring. These paper based sensors are shown to display an enhancement in sensitivity, as compared to control devices fabricated on non-porous polyimide substrates. These results have demonstrated the feasibility of paper-based printed devices towards manufacturing of a fully wearable, highly-sensitive, and wireless human performance monitor coupled to flexible electronics with the capability to communicate wirelessly to a smartphone or other electronics for data logging and analysis. 
    more » « less
  2. Plasma jet printing is an emerging alternative to popular 2-D printing techniques, such as inkjet and aerosol jet printing. The inherent nature of the plasma provides films with good adhesion upon printing without the need for thermal sintering. The reduced logistics and the ability to print a wide range of materials on rigid and flexible substrates make it a valuable technique for printed and flexible electronics. In this tutorial article, we discuss the principles behind plasma printing, printer hardware, and printing mechanisms and provide representative print results. 
    more » « less
  3. Abstract

    Despite significant progress in solution‐processing of 2D materials, it remains challenging to reliably print high‐performance semiconducting channels that can be efficiently modulated in a field‐effect transistor (FET). Herein, electrochemically exfoliated MoS2nanosheets are inkjet‐printed into ultrathin semiconducting channels, resulting in high on/off current ratios up to 103. The reported printing strategy is reliable and general for thin film channel fabrication even in the presence of the ubiquitous coffee‐ring effect. Statistical modeling analysis on the printed pattern profiles suggests that a spaced parallel printing approach can overcome the coffee‐ring effect during inkjet printing, resulting in uniform 2D flake percolation networks. The uniformity of the printed features allows the MoS2channel to be hundreds of micrometers long, which easily accommodates the typical inkjet printing resolution of tens of micrometers, thereby enabling fully printed FETs. As a proof of concept, FET water sensors are demonstrated using printed MoS2as the FET channel, and printed graphene as the electrodes and the sensing area. After functionalization of the sensing area, the printed water sensor shows a selective response to Pb2+in water down to 2 ppb. This work paves the way for additive nanomanufacturing of FET‐based sensors and related devices using 2D nanomaterials.

     
    more » « less
  4. Solution-phase printing of exfoliated graphene flakes is emerging as a low-cost means to create flexible electronics for numerous applications. The electrical conductivity and electrochemical reactivity of printed graphene has been shown to improve with post-print processing methods such as thermal, photonic, and laser annealing. However, to date no reports have shown the manipulation of surface wettability via post-print processing of printed graphene. Herein, we demonstrate how the energy density of a direct-pulsed laser writing (DPLW) technique can be varied to tune the hydrophobicity and electrical conductivity of the inkjet-printed graphene (IPG). Experimental results demonstrate that the DPLW process can convert the IPG surface from one that is initially hydrophilic (contact angle ∼47.7°) and electrically resistive (sheet resistance ∼21 MΩ □ −1 ) to one that is superhydrophobic (CA ∼157.2°) and electrically conductive (sheet resistance ∼1.1 kΩ □ −1 ). Molecular dynamic (MD) simulations reveal that both the nanoscale graphene flake orientation and surface chemistry of the IPG after DPLW processing induce these changes in surface wettability. Moreover, DPLW can be performed with IPG printed on thermally and chemically sensitive substrates such as flexible paper and polymers. Hence, the developed, flexible IPG electrodes treated with DPLW could be useful for a wide range of applications such as self-cleaning, wearable, or washable electronics. 
    more » « less
  5. Abstract

    Compliant pressure sensors are a key technology for wearable electronics and haptic interfaces. Making transistors pressure‐sensitive provides an opportunity to combine sensing and matrix readout characteristics. However, there is typically a trade‐off in pressure sensitivity, complexity of fabrication, and mechanical resilience. To overcome these challenges, an all solution‐processed kirigami‐inspired stretchable organic thin film transistor (OTFT) based pressure sensor array is introduced. The OTFTs integrate several novel processing and design strategies that include electrohydrodynamic (EHD) jet‐printed Ag nanowire (NW) electrodes that are partially embedded in a polyimide (PI) matrix. The EHD printing provides fine pattern control and the NW/PI composite improves mechanical stability. The OTFTs are made pressure sensitive by employing a porous styrene‐ethylene‐butylene‐styrene gate dielectric achieved using a breath figure method. The pore density can be controlled to achieve tunable pressure sensitivity. The OTFTs are shown to maintain performance under a small bending radius (1 mm) and can sense applied pressure from 0.75 to 25 kPa. Finally, a cut pattern is introduced into the substrate that imparts stretchability while maintaining pressure sensor functionality. The integration of the design features and processing methods introduced in this work enables mechanically resilient stretchable pressure sensors.

     
    more » « less