Ultra-violet (UV) light emitting diodes operating at 339 nm using transparent interband tunnel junctions are reported. Tunneling-based ultraviolet light emitting diodes were grown by plasma-assisted molecular beam epitaxy on 30% Al-content AlGaN layers. A low tunnel junction voltage drop is obtained through the use of compositionally graded n and p-type layers in the tunnel junction, which enhance hole density and tunneling rates. The transparent tunnel junction-based UV LED reported here show a low voltage drop of 5.55 V at 20 A/cm2 and an on-wafer external quantum efficiency of 1.02% at 80 A/cm2.
more »
« less
Demonstration of AlGaN Tunnel Junction p-Down UV Light Emitting Diodes
Ultra-violet light emitting diodes (UV-LEDs) and lasers based on the III-Nitride material system are very promising since they enable compact, safe, and efficient solid-state sources of UV light for a range of applications. The primary challenges for UV LEDs are related to the poor conductivity of p-AlGaN layers and the low light extraction efficiency of LED structures. Tunnel junction-based UV LEDs provide a distinct and unique pathway to eliminate several challenges associated with UV LEDs1-4. In this work, we present for the first time, a reversed-polarization (p-down) AlGaN based UV-LED utilizing bottom tunnel junction (BTJ) design. We show that compositional grading enables us to achieve the lowest reported voltage drop of 1.1 V at 20 A/cm2 among transparent AlGaN based tunnel junctions at this Al-composition. Compared to conventional LED design, a p-down structure offers lower voltage drop because the depletion barrier for both holes and electrons is lower due to polarization fields aligning with the depletion field. Furthermore, the bottom tunnel junction also allows us to use polarization grading to realize better p- and n-type doping to improve tunneling transport. The epitaxial structure of the UV-LED was grown by plasma-assisted molecular beam epitaxy (PAMBE) on metal-organic chemical vapor deposition (MOCVD)-grown n-type Al0.3Ga0.7N templates. The transparent TJ was grown using graded n++-Al0.3Ga0.7N→ n++-Al0.4Ga0.6N (Si=3×1020 cm-3) and graded p++-Al0.4Ga0.6N →p++-Al0.3Ga0.7N (Mg=1×1020 cm-3) to take advantage of induced 3D polarization charges. The high number of charges at the tunnel junction region leads to lower depletion width and efficient hole injection to the p-type layer. The UV LED active region consists of three 2.5 nm Al0.2Ga0.8N quantum wells and 7 nm Al0.3Ga0.6N quantum barriers followed by 12 nm of p- Al0.46Ga0.64N electron blocking layer (EBL). The active region was grown on top of the tunnel junction. A similar LED with p-up configuration was also grown to compare the electrical performance. The surface morphology examined by atomic force microscopy (AFM) shows smooth growth features with a surface roughness of 1.9 nm. The dendritic features on the surface are characteristic of high Si doping on the surface. The composition of each layer was extracted from the scan by high resolution x-ray diffraction (HR-XRD). The electrical characteristics of a device show a voltage drop of 4.9 V at 20 A/cm2, which corresponds to a tunnel junction voltage drop of ~ 1.1 V. This is the best lowest voltage for transparent 30% AlGaN tunnel junctions to-date and is comparable with the lowest voltage drop reported previously on non-transparent (InGaN-based) tunnel junctions at similar Al mole fraction AlGaN. On-wafer electroluminescence measurements on patterned light-emitting diodes showed single peak emission wavelength of 325 nm at 100 A/cm2 which corresponds to Al0.2Ga0.8N, confirming that efficient hole injection was achieved within the structure. The device exhibits a wavelength shift from 330 nm to 325 nm with increasing current densities from 10A/cm2 to 100A/cm2. In summary, we have demonstrated a fully transparent bottom AlGaN homojunction tunnel junction that enables p-down reversed polarization ultraviolet light emitting diodes, and has very low voltage drop at the tunnel junction. This work could enable new flexibility in the design of future III-Nitride ultraviolet LEDs and lasers.
more »
« less
- Award ID(s):
- 2034140
- NSF-PAR ID:
- 10482343
- Publisher / Repository:
- EMC
- Date Published:
- Format(s):
- Medium: X
- Location:
- Santa Barbara, CA, USA
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Strassburg, Martin ; Kim, Jong Kyu ; Krames, Michael R. (Ed.)AlGaN-based ultra-violet light emitting diodes (UV LEDs) are promising for a range of applications, including water purification, air disinfection and medical sensing. However, widespread adoption of UV LEDs is limited by the poor device efficiency. This has been attributed to the strong internal light absorption and poor electrical injection efficiency for the conventional UV LED structures, which typically use an absorbing p-GaN layer for p-type contact. Recent development of ultra-wide banggap AlGaN tunnel junctions enabled a novel UV LED design with the absence of the absorbing p-GaN contact layer. In this presentation, we will discuss recent progress of the AlGaN tunnel junctions and the development of tunnel junction-based UV LEDs, and discuss the challenges and future perspectives for the realization of high power, high efficiency UV LEDs.more » « less
-
more » « less
Abstract In this work, we demonstrate two-junction UV LEDs enabled by transparent tunnel junctions. Low voltage-drop tunnel junctions were realized in Al0.3Ga0.7N layers through a combination of high doping and compositional grading. Capacitance and current–voltage measurements confirmed the operation of two junctions in series. The voltage drop of the two-junction LED was 2.1 times that of an equivalent single-junction LED, and the two-junction LED had higher external quantum efficiency (147%) than the single junction.
-
more » « less
Potassium hydroxide (KOH) and ammonium sulfide
have been used as a surface passivation treatment to improve the electrical and optical performance of AlGaN nanowire ultraviolet (UV) light-emitting diodes (LEDs). Enhancements in photoluminescence at 335 nm (49%), optical output power (65%), and electroluminescence (83%), with respect to the as-grown nanowire LED are recorded for the AlGaN nanowire UV LEDs with surface passivation. These enhancements are attributed to the reduced nonradiative recombination on the nanowire surfaces. This study provides a potential surface passivation approach to produce high-power AlGaN nanowire LEDs operating in the UV spectrum. -
Morkoç, Hadis ; Fujioka, Hiroshi ; Schwarz, Ulrich T. (Ed.)Although AlGaN-based deep ultraviolet (UV) light-emitting diodes (LEDs) have been studied extensively, their quantum efficiency and optical output power still remain extremely low compared to the InGaN-based visible color LEDs. Electron leakage has been identified as one of the most possible reasons for the low internal quantum efficiency (IQE) in AlGaN based UV LEDs. The integration of a p-doped AlGaN electron blocking layer (EBL) or/and increasing the conduction band barrier heights with prompt utilization of higher Al composition quantum barriers (QBs) in the LED could mitigate the electron leakage problem to an extent, but not completely. In this context, we introduce a promising approach to alleviate the electron overflow without using EBL by utilizing graded concave QBs instead of conventional QBs in AlGaN UV LEDs. Overall, the carrier transportation, confinement capability and radiative recombination are significantly improved. As a result, the IQE, and output power of the proposed concave QB LED were enhanced by ~25.4% and ~25.6% compared to the conventional LED for emission at ~254 nm, under 60 mA injection current.more » « less
