An experimental study of the dynamics and droplet production in three mechanically generated plunging breaking waves is presented in this two-part paper. In the present paper (Part 2), in-line cinematic holography is used to measure the positions, diameters (
This content will become publicly available on July 25, 2024
An experimental study of the dynamics and droplet production in three mechanically generated plunging breaking waves is presented in this two-part paper. In the present paper (Part 1), the dynamics of the three breakers are studied through measurements of the evolution of their free surface profiles during 10 repeated breaking events for each wave. The waves are created from dispersively focused wave packets generated with three wave maker motions that differ primarily by small changes in their overall amplitude. Breaker profiles are measured with a cinematic laser-induced fluorescence technique covering a streamwise region of approximately one breaker wavelength and over a time of 3.4 breaker periods. The aligned profile data is used to create spatio-temporal maps of the ensemble average surface height and the standard deviation of both the local normal distance and the local arc length relative to the instantaneous mean profile. It is found that the mean and standard deviation maps contain strongly correlated localized features and indicate that the transition from laminar to turbulent flow is a highly repeatable process. Regions of high standard deviation include the splash created by the plunging jet impact and subsequent splash impacts at the front of the breaking region as well as the site where the air pocket entrained under the plunging jet at the moment of jet tip impact comes to the surface and pops. In Part 2 (Erinin
- Award ID(s):
- 1925060
- NSF-PAR ID:
- 10483875
- Publisher / Repository:
- Journal of Fluid Mechanics
- Date Published:
- Journal Name:
- Journal of Fluid Mechanics
- Volume:
- 967
- ISSN:
- 0022-1120
- Page Range / eLocation ID:
- A35
- Subject(s) / Keyword(s):
- ["Wave breaking, air\/sea interaction"]
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
$d\geq 100\ \mathrm {\mu }{\rm m}$ et al. ,J. Fluid Mech. , vol. 967, 2023, A35) as the droplets move up across a horizontal measurement plane located just above the wave crests. It is found that there are four major mechanisms for droplet production: closure of the indentation between the top surface of the plunging jet and the splash that it creates, the bursting of large bubbles that were entrapped under the plunging jet at impact, splashing and bubble bursting in the turbulent zone on the front face of the wave and the bursting of small bubbles that reach the water surface at the crest of the non-breaking wave following the breaker. The droplet diameter distributions for the entire droplet set for each breaker are fitted with power-law functions in separate small- and large-diameter regions. The droplet diameter where these power-law functions cross increases monotonically from 820 to 1480$\mathrm {\mu }{\rm m}$ -
more » « less
Abstract An experimental investigation of droplet generation by a plunging breaking wave is presented. In this work, simultaneous measurements of the wave crest profile evolution and of droplets ranging in radius down to 50 μm for a mechanically generated plunging breaker during many repeated breaking events in freshwater are performed. We find three distinct time zones of droplet production, first when the jet impacts the free surface upstream of the wave crest, second when the large air bubbles entrapped by the plunging jet impact reach the free surface and burst, and third when smaller bubbles burst upon reaching the free surface later in the breaking process. These subprocesses account for 22%, 44%, and 34%, respectively, of the average of 653 droplets produced per breaking event. The probability distributions of the ranges of large and small droplet radii are well represented by power law functions that intersect at a radius of 418 μm.
-
more » « less
Abstract This is the first of a 2‐part series concerning remote observation and wave‐by‐wave analysis of the onset of breaking in the surf zone. In the surf zone, breaking waves drive nearshore circulation, suspend sediment, and promote air‐sea gas exchange. Nearshore wave model predictions often diverge from
in situ measurements near the break point location because common parameterizations do not account for the rapid changes that occur near the onset of breaking. This work presents extensive methodology to combine data from a line‐scanning LIDAR and thermal infrared cameras to detect breaking, classify breaker type, and measure geometric wave parameters on a wave‐by‐wave basis, which can be used to improve breaker parameterizations. Over 2,600 non‐breaking and 1,600 breaking waves are analyzed from data collected at the USACE Field Research Facility in Duck, NC, including 413 spilling and 111 plunging waves for which the onset of breaking was observed. Wave height is estimated using a spatio‐temporal method for wave tracking that preserves the sea surface elevation maximum and overcomes field of view limitations. Methods for estimating instantaneous wave speed are refined by fitting a skewed Gaussian function to each wave profile before tracking the peaks. Wave slope is estimated from a linear fit to the upper 80% of the wave face, which provides a robust metric and strong correlation with geometric wave slope defined relative to mean sea level. Finally, breaking wave face foam coverage is analyzed to assess common model assumptions about roller length for wave energy dissipation parameterizations. -
more » « less
The effects of surfactants on a mechanically generated plunging breaker are studied experimentally in a laboratory wave tank. Waves are generated using a dispersively focused wave packet with a characteristic wavelength of
$\lambda _0 = 1.18$ $\Delta \mathcal {E}$ $\sigma _0$ -
We present high-resolution three-dimensional (3-D) direct numerical simulations of breaking waves solving for the two-phase Navier–Stokes equations. We investigate the role of the Reynolds number ( Re , wave inertia relative to viscous effects) and Bond number ( Bo , wave scale over the capillary length) on the energy, bubble and droplet statistics of strong plunging breakers. We explore the asymptotic regimes at high Re and Bo , and compare with laboratory breaking waves. Energetically, the breaking wave transitions from laminar to 3-D turbulent flow on a time scale that depends on the turbulent Re up to a limiting value $Re_\lambda \sim 100$ , consistent with the mixing transition in other canonical turbulent flows. We characterize the role of capillary effects on the impacting jet and ingested main cavity shape and subsequent fragmentation process, and extend the buoyant-energetic scaling from Deike et al. ( J. Fluid Mech. , vol. 801, 2016, pp. 91–129) to account for the cavity shape and its scale separation from the Hinze scale, $r_H$ . We confirm two regimes in the bubble size distribution, $N(r/r_H)\propto (r/r_H)^{-10/3}$ for $r>r_H$ , and $\propto (r/r_H)^{-3/2}$ for $r
Warning: Leaving National Science Foundation Website
You are now leaving the National Science Foundation website to go to a non-government website.
Website:
NSF takes no responsibility for and exercises no control over the views expressed or the accuracy of the information contained on this site. Also be aware that NSF's privacy policy does not apply to this site.
