An official website of the United States government
An experimental study was conducted to compare various strategies for UAV propeller icing mitigation. With a propeller model with an untreated hydrophilic blade as the comparison baseline, three icing protection systems (IPSs) were evaluated systematically: 1) a passive method with the propeller blade coated with a super-hydrophobic surface (SHS) coating; 2) an active IPS design to forcefully heat the entire blade surface; and 3) a hybrid IPS design with only limited surface heating along the blade leading edge and the SHS-coated blade. While the passive method with the SHS-coated blade was found to be only marginally effective under the glaze icing condition, it became ineffective or even further deteriorated the propeller performance under the mixed and rime icing conditions. While the active IPS design to forcefully heat the entire blade surface was found to be able to prevent ice accretion on most of the blade surface, some minor “ice crowns” were still observed to accrete near the blade tip. The hybrid IPS design was demonstrated to keep the entire blade surface ice-free under all the icing conditions with substantially less power consumption (i.e., [Formula: see text] power saving), rendering it a compelling UAV propeller icing mitigation strategy.
more »
« less
Comparative Study of Using Superhydrophobic and Icephobic Surface Coatings for Aircraft Icing Mitigation
We report a comparative study to evaluate the effects of surface coatings with different hydrophobicities and icephobicities on the performance of a hybrid anti-/de-icing system that integrates surface heating with hydro-/ice-phobic coating for aircraft icing mitigation. While a flexible electric film heater wrapped around the leading edge of an airfoil/wing model was used to heat the airfoil frontal surface to prevent ice accretion near the airfoil leading edge, three different kinds of coatings were applied to coat the airfoil model at three distinct spanwise locations, which included an icephobic coating with an outstanding icephobicity but a weak hydrophobicity; a superhydrophobic surface (SHS) coating with outstanding water repellency but a moderate icephobicity; and a commonly used hydrophilic coating with poor hydrophobicity and poor icephobicity. Surface wettability was found to play a more important role than icephobicity in affecting the performance of the hybrid anti-/de-icing systems. In comparison to the approach of forceful heating the hydrophilic airfoil surface, the hybrid approach with the SHS coating was found to be able to achieve about 90% energy savings in keeping the entire airfoil surface ice-free; the corresponding energy savings for the hybrid system with the icephobic coating was only about 10%.
more »
« less
- PAR ID:
- 10491201
- Publisher / Repository:
- American Institute of Aeronautics and Astronautics
- Date Published:
- Journal Name:
- AIAA Journal
- ISSN:
- 0001-1452
- Page Range / eLocation ID:
- 1 to 13
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract Anti‐icing and icephobic materials play a crucial role in demanding applications ranging from energy to transportation systems operating in frigid climates. Despite remarkable advancements in the development of such surface coatings, the use of anti/de‐icing chemicals remains one of the go‐to solutions for ice management. However, they are notoriously prone to removal by shear forces and dissolution. Herein, the design rationale for developing a family of cryoprotectant and phase‐change material (PCM)‐based compositions in the form of mixtures, non‐aqueous emulsions‐creams, and gels that can substantially overcome such challenges is reported. This is achieved through the sustenance of an in‐situ‐generated surface hydration layer that protects the underlying substrate from a variety of foulants, varying from ice to disease‐causing bacteria. Each formulation utilizes unique chemistry to curtail the embodied cryoprotectant loss and can be easily applied as an all‐in‐one sprayable/paintable coating capable of significantly outperforming untreated industrial materials in terms of their ability to delay condensation‐frosting and shed ice simultaneously. Concomitantly, an array of formulation‐specific functionalities is observed in the family, which includes optical transparency, mechanical durability, high shear‐flow stability, and self‐healing characteristics.more » « less
-
Hazardous atmospheric icing conditions occur at sub-zero temperatures when droplets come into contact with aircraft and freeze, degrading aircraft performance and handling, introducing bias into some of the vital measurements needed for aircraft operation (e.g., air speed). Nonetheless, government regulations allow certified aircraft to fly in limited icing environments. The capability of aircraft sensors to identify all hazardous icing environments is limited. To address the current challenges in aircraft icing detection and protection, we present herein a platform designed for in-flight testing of ice protection solutions and icing detection technologies. The recently developed Platform for Ice-accretion and Coatings Tests with Ultrasonic Readings (PICTUR) was evaluated using CFD simulations and installed on the National Research Council Canada (NRC) Convair-580 aircraft that has flown in icing conditions over North East USA, during February 2022. This aircraft is a flying laboratory, equipped with more than 40 sensors providing a comprehensive characterization of the flight environment including measurements of temperature, pressure, wind speed and direction, water droplet size and number distribution, and hydrometeor habits imagery. The flight tests of the platform included assessment of passive icephobic coatings as well as heat-assisted tests. Monitoring tools included visual high resolution, real-time inspection of the surface as well as detection of surface ice using NRC’s Ultrasonic Ice Accretion Sensors (UIAS). In this paper, we present the new platform and show some preliminary commissioning results of PICTUR, collected inflight under, predominantly, supercooled small droplets and supercooled large drops (SLD) icing conditions. The combination of the platform and the complementary sensors on the aircraft demonstrated an effective and unique technique for icing studies in a natural environment.more » « less
-
Accumulated dust on solar cover glass reduces transmittance, leading to decreased energy efficiency of photovoltaic (PV) modules. Hydrophobic coatings on solar cover glass have been shown to provide anti-soiling properties when exposed to a condensing environment (e.g. dew). The addition of hydrophilic features along the top edge of the hydrophobic coated glass enhances condensation rates and can be used to achieve self-cleaning of the surfaces. However, to date, relatively long times have been required to clean the surfaces. In this study, we developed a new design for hydrophilic features that reduce the time required to clean the surface in laboratory tests as measured by laser scanning microscopy, optical photographs and UV–vis spectroscopy. The dagger-shaped features improve self-cleaning performance by a combination of three factors: a silica nanoparticle (NP) hydrophilic coating which enhances condensation rate due to a low water contact angle (WCA) and nano-scale porosity; the stepwise transition from the low WCA silica NP region to the high WCA silanized hydrophobic region via a bare glass transition zone; and the pointed shape of the hydrophobic dagger features which further minimizes the barrier for transport of droplets from the condensing region to the high-mobility, hydrophobic, region of the surface. The hydrophilic silica nanoparticle-coated dagger features not only improve the self-cleaning efficiency of the hydrophobic surfaces but also increase the overall amount of water harvested. Such coating designs provide an effective approach to reducing maintenance costs as well as increasing the overall energy output of PV panels.more » « less
-
Due to the emergence of wide-spread infectious diseases, there is a heightened need for antimicrobial and/or antifouling coatings that can be used to prevent infection and transmission in a variety of applications, ranging from healthcare devices to public facilities. While antimicrobial coatings kill pathogenic bacteria upon contact with the surface, the antimicrobial function alone often lacks long-term effectiveness due to the accumulation of dead cells and their debris on the surface, thus reducing the performance of the coating over time. Therefore, it is desirable to develop coatings with the dual functions of antimicrobial efficacy and fouling resistance, in which antifouling coatings provide the added benefit of preventing the adhesion of dead cells and debris. Leveraging the outstanding antifouling properties of zwitterionic coatings, we synthesized copolymers with this antimicrobial-antifouling dual function by immobilizing lysozyme, a common antimicrobial enzyme, to the surface of a pyridinium-based zwitterionic copolymer. Specifically, poly(4-vinylpyridine- co -pentaflurophenyl methacrylate- co -divinyl benzene) [P(4VP-PFPMA-DVB)] thin films were synthesized by an all-dry vapor deposition technique, initiated Chemical Vapor Deposition, and derivatized using 1,3-propane sultone to obtain sulfobetaine moieties. Lysozyme, known to hydrolyze polysaccharides in the cell wall of Gram-positive bacteria, was immobilized by forming amide bonds with the copolymer coating via nucleophilic substitution of the pentafluorophenyl group. The antifouling and antibacterial performance of the novel lysozyme-zwitterionic coating was tested against Gram-positive Bacillus subtilis and Gram-negative Pseudomonas aeruginosa . A reduction in surface adhesion of 87% was achieved for P. aeruginosa , and of 75% for B. subtilis , when compared to a common poly(vinyl chloride) surface. The lysozyme-zwitterionic coating also deactivated 67% of surface-attached Gram-positive bacteria, B. subtilis . This novel dual-function material can produce anti -infection surfaces for medical devices and surgical tools, personal care products, and surfaces in public facilities.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.2514/1.J063579
