An official website of the United States government
Abstract Dilatant hardening is one proposed mechanism that causes slow earthquakes along faults. Previous experiments and models show that dilatant hardening can stabilize fault rupture and slip in several lithologies. However, few studies have systematically measured the mechanical behavior across the transition from dynamic to slow rupture or considered how the associated damage varies. To constrain the processes and scales of dilatant hardening, we conducted triaxial compression experiments on cores of Crab Orchard sandstone and structural analyses using micro‐computed tomography imaging and petrographic analysis. Experiments were conducted at an effective confining pressure of ∼10 MPa, while varying confining pressure (10–130 MPa) and pore fluid pressure (1–120 MPa). Above 15 MPa pore fluid pressure, dilatant hardening slows the rate of fault rupture and slip and deformation becomes more distributed amongst multiple faults as microfracturing increases. The resulting increase in fracture energy has the potential to control fault slip behavior.
more »
« less
Path and Slip Dependent Behavior of Shallow Subduction Shear Zones During Fluid Overpressure
Abstract Elevated pore fluid pressure is proposed to contribute to slow earthquakes along shallow subduction plate boundaries. However, the processes that create high fluid pressure, disequilibrium compaction and dehydration reactions, lead to different effective stress paths in fault rocks. These paths are predicted by granular mechanics frameworks to lead to different strengths and deformation modes, yet granular mechanics do not predict their effects on fault stability. To evaluate the role of fluid overpressure on shallow megathrust strength and slip behavior, we conducted triaxial shear experiments on chlorite and celadonite rich gouge layers. Experiments were conducted at constant temperature (130 and 100°C), confining pressure (130 and 140 MPa), and pore fluid pressures (between 10 and 120 MPa). Fluid overpressure due to disequilibrium compaction was simulated by increasing confining and pore fluid pressure synchronously without exceeding the target effective pressure, whereas overpressure due to dehydration reactions was simulated by first loading the sample to a target isotropic effective pressure and then increasing pore fluid pressure to reduce the effective pressure. We find that the effects of fluid pressure and stress path on the mechanical behavior of the chlorite and celadonite gouges can generally be described using the critical state soil mechanics (CSSM) framework. However, path effects are more pronounced and persist to greater displacements in chlorite because its microstructure is more influenced by stress path. Due to its effects on microstructure, the stress path also imparts greater control on the rate‐dependence of chlorite strength, which is not predicted by CSSM.
more »
« less
- Award ID(s):
- 1945264
- PAR ID:
- 10500333
- Publisher / Repository:
- DOI PREFIX: 10.1029
- Date Published:
- Journal Name:
- Journal of Geophysical Research: Solid Earth
- Volume:
- 129
- Issue:
- 4
- ISSN:
- 2169-9313
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract Carbonate sediments play a prominent role on the global geological stage as they store more than $$60\%$$ 60 % of world’s oil and $$40\%$$ 40 % of world’s gas reserves. Prediction of the deformation and failure of porous carbonates is, therefore, essential to minimise reservoir compaction, fault reactivation, or wellbore instability. This relies on our understanding of the mechanisms underlying the observed inelastic response to fluid injection or deviatoric stress perturbations. Understanding the impact of deformation/failure on the hydraulic properties of the rock is also essential as injection/production rates will be affected. In this work, we present new experimental results from triaxial deformation experiments carried out to elucidate the behaviour of a porous limestone reservoir analogue (Savonnières limestone). Drained triaxial and isotropic compression tests were conducted at five different confining pressures in dry and water-saturated conditions. Stress–strain data and X-ray tomography images of the rock indicate two distinct types of deformation and failure regimes: at low confinement (10 MPa) brittle failure in the form of dilatant shear banding was dominant; whereas at higher confinement compaction bands orthogonal to the maximum principal stress formed. In addition to the pore pressure effect, the presence of water in the pore space significantly weakened the rock, thereby shrinking the yield envelope compared to the dry conditions, and shifted the brittle–ductile transition to lower effective confining pressures (from 35 MPa to 29 MPa). Finally, permeability measurements during deformation show a reduction of an order of magnitude in the ductile regime due to the formation of the compaction bands. These results highlight the importance of considering the role of the saturating fluid in the brittle–ductile response of porous rocks and elucidate some of the microstructural processes taking place during this transition.more » « less
-
Abstract We study stress, pressure, and rock properties in evolving accretionary wedges using analytical formulations and geomechanical models. The evolution of the stress state from that imposed by uniaxial burial seaward of the trench to Coulomb failure within the wedge generates overpressure and drives compaction above the décollement. Changes in both mean and shear stress generate overpressure and shear‐induced pressures play a particularly important role in the trench area. In the transition zone between uniaxial burial and Coulomb failure, shear‐induced overpressures increase more than overburden and are higher than footwall pressures. This rapid increase in overpressure reduces the effective normal stress and weakens the plate interface along a zone that onsets ahead of the trench and persists well into the subduction zone. It also drives dewatering at the trench, which enables compaction of the hanging‐wall sediments and a porosity offset at the décollement. Within the accretionary wedge, sediments are at Coulomb failure and the pore pressure response is proportional to changes in mean stress. Low permeability and high convergence rates promote overpressure generation in the wedge, which limits sediment strength. Our results may provide a hydromechanical explanation for a wide range of observed behaviors, including the development of protothrust zones, widespread occurrence of shallow slow earthquake phenomena, and the propagation of large shallow coseismic slip.more » « less
-
Abstract Fault-zone fluids control effective normal stress and fault strength. While most earthquake models assume a fixed pore fluid pressure distribution, geologists have documented fault valving behavior, that is, cyclic changes in pressure and unsteady fluid migration along faults. Here we quantify fault valving through 2-D antiplane shear simulations of earthquake sequences on a strike-slip fault with rate-and-state friction, upward Darcy flow along a permeable fault zone, and permeability evolution. Fluid overpressure develops during the interseismic period, when healing/sealing reduces fault permeability, and is released after earthquakes enhance permeability. Coupling between fluid flow, permeability and pressure evolution, and slip produces fluid-driven aseismic slip near the base of the seismogenic zone and earthquake swarms within the seismogenic zone, as ascending fluids pressurize and weaken the fault. This model might explain observations of late interseismic fault unlocking, slow slip and creep transients, swarm seismicity, and rapid pressure/stress transmission in induced seismicity sequences.more » « less
-
Earthquake swarms attributed to subsurface fluid injection are usually assumed to occur on faults destabilized by increased pore-fluid pressures. However, fluid injection could also activate aseismic slip, which might outpace pore-fluid migration and transmit earthquake-triggering stress changes beyond the fluid-pressurized region. We tested this theoretical prediction against data derived from fluid-injection experiments that activated and measured slow, aseismic slip on preexisting, shallow faults. We found that the pore pressure and slip history imply a fault whose strength is the product of a slip-weakening friction coefficient and the local effective normal stress. Using a coupled shear-rupture model, we derived constraints on the hydromechanical parameters of the actively deforming fault. The inferred aseismic rupture front propagates faster and to larger distances than the diffusion of pressurized pore fluid.more » « less
