An official website of the United States government
Bulk nanostructured metals introduced by severe plastic deformation contain an excess of lattice defects. A nanostructured copper (Cu) processed by a high-pressure torsion technique was examined during in situ heating to investigate microstructural relaxation and quantify the evolution of microstructural parameters using high-energy synchrotron microbeam X-ray diffraction. While general microstructural relaxations, such as recovery, recrystallization, and subsequent grain growth, were observed, the key microstructural parameters, including grain size, microstrain, dislocation density, and thermal expansion coefficient, and their changes at critical temperatures were uniquely described and quantified through diffraction data. Based on this analysis, the stored energies driving thermally activated microstructural changes were estimated for individual defect types — grain boundaries, dislocations, and vacancies — that are expected to significantly influence the relaxation behavior of nanostructured Cu. This study demonstrates the effectiveness of diffraction characterization techniques for gaining a comprehensive understanding of the thermal stability of bulk nanostructured materials.
more »
« less
Recrystallization of bulk nanostructured magnesium alloy AZ31 after severe plastic deformation: an in situ diffraction study
Abstract The magnesium alloy AZ31, which has undergone high-pressure torsion processing, was subjected to in situ annealing microbeam synchrotron high-energy X-ray diffraction and compared to the as-received rolled sheet material that was investigated through in situ neutron diffraction. While the latter only exhibits thermal expansion and minor recovery, the nanostructured specimen displays a complex evolution, including recovery, strong recrystallization, phase transformations, and various regimes of grain growth. Nanometer-scale grain sizes, determined using Williamson–Hall analysis, exhibit seamless growth, aligning with the transition to larger grains, as assessed through the occupancy of single-grain reflections on the diffraction rings. The study uncovers strain anomalies resulting from thermal expansion, segregation of Al atoms, and the kinetics of vacancy creation and annihilation. Notably, a substantial number of excess vacancies were generated through high-pressure torsion and maintained for driving the recrystallization and forming highly activated volumes for diffusion and phase precipitation during heating. The unsystematic scatter observed in the Williamson–Hall plot indicates high dislocation densities following severe plastic deformation, which significantly decrease during recrystallization. Subsequently, dislocations reappear during grain growth, likely in response to torque gradients in larger grains. It is worth noting that the characteristics of unsystematic scatter differ for dislocations created at high and low temperatures, underscoring the strong temperature dependence of slip system activation. Graphical Abstract
more »
« less
- Award ID(s):
- 2051205
- PAR ID:
- 10520804
- Publisher / Repository:
- Springer Nature
- Date Published:
- Journal Name:
- Journal of Materials Science
- Volume:
- 59
- Issue:
- 14
- ISSN:
- 0022-2461
- Page Range / eLocation ID:
- 5831-5853
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Nanostructured steels are expected to have enhanced irradiation tolerance and improved strength. However, they suffer from poor microstructural stability at elevated temperatures. In this study, Fe–21Cr–5Al–0.026C (wt%) Kanthal D (KD) alloy belonging to a class of (FeCrAl) alloys considered for accident‐tolerant fuel cladding in light‐water reactors is nanostructured using two severe plastic deformation techniques of equal‐channel angular pressing (ECAP) and high‐pressure torsion (HPT), and their thermal stability between 500–700 °C is studied and compared. ECAP KD is found to be thermally stable up to 500 °C, whereas HPT KD is unstable at 500 °C. Microstructural characterization reveals that ECAP KD undergoes recovery at 550 °C and recrystallization above 600 °C, while HPT KD shows continuous grain growth after annealing above 500 °C. Enhanced thermal stability of ECAP KD is from significant fraction (>50%) of low‐angle grain boundaries (GBs) (misorientation angle 2–15°) stabilizing the microstructure due to their low mobility. Small grain sizes, a high fraction (>80%) of high‐angle GBs (misorientation angle >15°) and accordingly a large amount of stored GB energy, serve as the driving force for HPT KD to undergo grain growth instead of recrystallization driven by excess stored strain energy.more » « less
-
Severe plastic deformation (SPD) has been known for decades to provide microstructural refinement under a hydrostatic stress state by introducing a tremendous quantity of lattice defects, including vacancies, dislocations, and grain boundaries, leading to enhanced mechanical properties. Many SPD processes have been well studied and utilized for the processing of ultrafine-grained (UFG) metals and materials. One major challenge with SPD-processed UFG materials is their limited applicability, primarily due to their microstructural stability at elevated temperatures and the difficulty of scaling up to larger sizes or volumes. To first understand the thermal stability of UFG material, a copper prepared by high-pressure torsion, a technique that can achieve true nano-scale grains in bulk samples, was evaluated using two novel in situ techniques of micro-beam high-energy synchrotron X-ray diffraction. These are, namely, monochromatic X-ray beams that yield changes in microstructure with time and temperature, and a polychromatic X-ray beam that determines grain reorientation behavior during microstructural relaxation. Furthermore, a new processing technique named cold angular rolling process (CARP) demonstrated some promise as an SPD technique for producing theoretically unlimited lengths of strength-enhanced copper sheets at room temperature with a relatively low energy consumption. Additional miniature tensile testing incorporating digital image correlation (DIC) method and microstructural analysis utilizing high-energy X-ray diffraction determined the influence of CARP having higher shear strain hardening in comparison with other established techniques. This study highlights the significance of lattice-defect influenced mechanical properties and microstructure of UFG obtained across multi-length scales and volumes, which are critical for guiding the control and scalable production of advanced materials for commercialization.more » « less
-
The static recrystallization and grain growth of a hybrid AZ31/Mg-0.6Gd (wt%) material fabricated by high pressure torsion (HPT) through 20 turns were explored after isochronal annealing at 150, 250, 350 and 450 ◦C for 1 h using electron backscatter diffraction, transmission electron microscopy and Vickers microhardness measurements. The results reveal heterogeneity in the grain size distributions of the AZ31 and Mg-0.6Gd regions after annealing at the lower temperatures of 150 and 250 ◦C leading to a clear AZ31/Mg-0.6Gd interfacial border. At the higher temperatures of 350 and 450 ◦C the AZ31/Mg-0.6Gd interfaces were not well-defined owing to the occurrence of grain growth. It is shown that grain growth is restricted in the AZ31 and Mg-0.6Gd regions due to the presence of stable nano-size Al8Mn5 particles and the precipitation of Mg17Al12 and Mg12Zn at 250 ◦C and of Mg5Gd and Mg12Gd phases at 350 and 450 ◦C. The distribution of the basal texture in both regions was strongly controlled by dynamic recrystallization, precipitation and grain growth. The values of the microhardness over the radial cross-sections of the hybrid discs decrease and become more uniform, in the range of ~35–66 Hv, with increasing annealing temperature.more » « less
-
null (Ed.)Grain growth under shear annealing is crucial for controlling the properties of polycrystalline materials. However, their microscopic kinetics are not well understood because individual atomic trajectories are difficult to track. Here, we study grain growth with single-particle kinetics in colloidal polycrystals using video microscopy. Rich grain-growth phenomena are revealed in three shear regimes, including the normal grain growth (NGG) in weak shear melting–recrystallization process in strong shear. For intermediate shear, early stage NGG is arrested by built-up stress and eventually gives way to dynamic abnormal grain growth (DAGG). We find that DAGG occurs via a melting–recrystallization process, which naturally explains the puzzling stress drop at the onset of DAGG in metals. Moreover, we visualize that grain boundary (GB) migration is coupled with shear via disconnection gliding. The disconnection-gliding dynamics and the collective motions of ambient particles are resolved. We also observed that grain rotation can violate the conventional relation R × θ = c o n s t a n t (R is the grain radius, and θ is the misorientation angle between two grains) by emission and annihilation of dislocations across the grain, resulting in a step-by-step rotation. Besides grain growth, we discover a result in shear-induced melting: The melting volume fraction varies sinusoidally on the angle mismatch between the triangular lattice orientation of the grain and the shear direction. These discoveries hold potential to inform microstructure engineering of polycrystalline materials.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript
- Journal Article:
- https://doi.org/10.1007/s10853-023-09250-4
