An official website of the United States government
Determination of olefins in pyrolysis oils from waste plastics and tires is crucial for optimizing the pyrolysis process and especially for the further advanced valorization of these oils in terms of the circular economy. Identifying olefins, even using high-resolution techniques like GC×GC, is challenging without TOF-MS, which allows modification of the ionization step. Currently, the only method for determining olefins in plastic pyrolysis oils is GC-VUV, recently standardized as ASTM D8519. However, TOF-MS and VUV are not affordable instruments for many research teams working on plastics recycling. This paper introduces a simple method for the selective micro-scale adsorption of olefins over AgNO3/SiO2, followed by the GC×GC-FID analysis. Olefins are determined indirectly from the loss of chromatographic area in respective hydrocarbon groups before and after removal. Only 50 μL sample and 15 min of sample separation are needed. Our method was extensively validated and provides a reliable determination of olefin content in a wide range of pyrolysis oils from plastics and tires and their products after mild hydrotreatment. It is affordable to all researchers and industrial companies working on plastics recycling by thermochemical processes as it does not require an MS detector.
more »
« less
A comparative study of aromatic content in pyrolysis oils from waste plastics and tires: Assessing common refinery methods
The conversion of waste plastics and tires via pyrolysis to pyrolysis oil represents one of the most promising ways of chemical recycling. Determining aromatics in pyrolysis oils from these feedstocks is crucial for their utilization as both petrochemicals and fuels. In this study, we compared three standard methods commonly available in refinery laboratories (ASTM D1319 − FIA, EN12916 − HPLC-RI, ASTM D8396 − GC × GC-FID) for analyzing aromatic content across a wide range of waste plastic pyrolysis oils, their middle distillate fractions, and hydrotreated products. Using model compounds, we explained most of the observed differences in aromatic content determined by these methods. HPLC-RI and FIA resulted in significant errors. For instance, the FIA reports some dienes and heterocompounds as aromatics. The results from HPLC-RI showed that monoaromatics are overestimated, while polyaromatics are underestimated. Among the tested methods, GC × GC-FID provided the most reliable results.
more »
« less
- Award ID(s):
- 2112554
- PAR ID:
- 10528244
- Publisher / Repository:
- Elsevier
- Date Published:
- Journal Name:
- Fuel
- Volume:
- 369
- Issue:
- C
- ISSN:
- 0016-2361
- Page Range / eLocation ID:
- 131714
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Global polystyrene (PS) waste accumulates at a rate of 28 million tons annually, while recycling rates stay at 1.3 %. PS degrades into microplastics, releasing various chemicals that affect ecosystems and human health. Conventional waste treatment methods are ineffective in reducing PS waste accumulation. This study developed batch low-pressure hydrothermal processing (LP-HTP) methods to convert PS to oils. Oil yields of 96–99 % were obtained with 1–2 % char and up to 2 % gas at average temperatures of 341–424°C for 19–75 minutes. Reversible reactions between monomers (C6-C9) and poly-aromatics (C10-C20+) were found to limit monomer yields. A two-step kinetic model accounting for the reversible reactions was developed. Temperature histories of the batch experiments were considered such that the estimated kinetic parameters were independent of reactor heating or cooling rates. The predicted yields of monomers and poly-aromatics agreed with experimental yields to within 6 %. The model predicted increasing monomer yields with decreasing PS loadings. This predictive model can aid future process optimization and scale-up. PS and polyolefins were co-processed to produce oils with 87 % yields and higher aromatic contents than oils produced from polyolefins alone. LP-HTP methods required no catalyst, had higher oil yields and less char formation than pyrolysis, and used much lower operating pressures and energy than supercritical water liquefaction. The methods also potentially have lower environmental impacts and 4.7 times higher energy recovery than incineration. The oils from LP-HTP, if separated into pure monomers, can be used as chemical feedstocks to achieve a circular use of hydrocarbons.more » « less
-
Despite the promise of waste-to-energy conversions, bio-oils produced via thermochemical techniques such as pyrolysis suf- fer from high viscosity and acidity, which render the oils unstable and corrosive. While pyrolysis biocrude can be upgraded downstream, the use of precious metal catalysts limits the economic feasibility of biomass to biofuel conversions. To address these economic limitations, the present work explores the use of clay minerals as inexpensive catalysts to upgrade bio-oils in situ. Cherry pits, a representative carbonaceous agro-industrial waste, were pyrolyzed at 600 °C for 1 h in the presence of a series of clay minerals. For some clays, the bio-oils produced from catalyzed pyrolysis exhibited lower oxygen and fatty acid content than bio-oil from non-catalyzed pyrolysis. The heterogeneous clay-cherry pit biochar mixtures had higher surface areas and surface chemistries with increased free and intermolecularly bonded hydroxyl groups relative to those of pure cherry pit biochar. However, adsorption studies using methylene blue as a model organic contaminant showed that these heterogenous chars had a decreased adsorption capacity, likely due to a loss of surface functional groups. The addition of clay materials to the pyrolysis stream yields a biocrude more amendable to downstream upgrading and a heterogeneous biochar-clay mixture capable of (though certainly not optimized for) adsorbing a model organic compound.more » « less
-
Biofuels produced via thermochemical conversions of waste biomass could be sustainable alternatives to fossil fuels but currently require costly downstream upgrading to be used in existing infrastructure. In this work, we explore how a low-cost, abundant clay mineral, bentonite, could serve as an in situ heterogeneous catalyst for two different thermochemical conversion processes: pyrolysis and hydrothermal carbonization (HTC). Avocado pits were combined with 20 wt% bentonite clay and were pyrolyzed at 600 °C and hydrothermally carbonized at 250 °C, commonly used conditions across the literature. During pyrolysis, bentonite clay promoted Diels–Alder reactions that transformed furans to aromatic compounds, which decreased the bio-oil oxygen content and produced a fuel closer to being suitable for existing infrastructure. The HTC bio-oil without the clay catalyst contained 100% furans, mainly 5-methylfurfural, but in the presence of the clay, approximately 25% of the bio-oil was transformed to 2-methyl-2-cyclopentenone, thereby adding two hydrogen atoms and removing one oxygen. The use of clay in both processes decreased the relative oxygen content of the bio-oils. Proximate analysis of the resulting chars showed an increase in fixed carbon (FC) and a decrease in volatile matter (VM) with clay inclusion. By containing more FC, the HTC-derived char may be more stable than pyrolysis-derived char for environmental applications. The addition of bentonite clay to both processes did not produce significantly different bio-oil yields, such that by adding a clay catalyst, a more valuable bio-oil was produced without reducing the amount of bio-oil recovered.more » « less
-
Zhang, Mingming (Ed.)We employed two compelling and distinct methods, Fourier Transform Infrared Spectroscopy (FTIR) and Ramped Pyrolysis Oxidation (Ramped PyrOx), to examine the quality of organic matter (OM) stored in four peatlands located along a latitudinal gradient (Tropical (4˚N), Subtropical (27˚N), Boreal (48˚N), and Polar (68˚N)). FTIR was used to quantify the relative abundance of carbohydrates, a relatively labile compound class, and aromatics, which are more recalcitrant, in a sample set of four peat cores. These samples were then prepared using Ramped PyrOx, a second, independent method of determining OM quality that mimics the natural diagenetic maturation of OM that would take place over long timescales. Previous large-scale studies using FTIR to evaluate OM quality have observed that it generally increases with increasing latitude (more carbohydrates, less aromatics). Here, we demonstrate that the Ramped PyrOx approach both validates and complements the FTIR approach. The data stemming from each Ramped PyrOx preparation was input to a model that generates an estimated probability density function of the activation energy (E) required to break the C bonds in the sample. We separated these functions into three fractions (“lowE,” “mediumE,” and “highE”) to create Ramped PyrOx variables that could be quantitatively compared to the compound class abundance data from FTIR. In assessing the agreement between the two methods, we found three significant relationships between Ramped PyrOx and FTIR variables. LowEfractions and carbohydrate content were positively correlated (R2= 0.51) while lowEfractions were negatively correlated with aromatic content (R2= 0.58). MediumEfractions were found to be positively correlated with aromatics (R2= 0.69).more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1016/j.fuel.2024.131714
