An official website of the United States government
This work focused on understanding how swirl influences the blowoff limit and process in lean-premixed, swirl-stabilized flames. Two initial equivalence ratios (Ф0 = 0.8 and 1.0) were used to study the effect of swirl number (S = 0.80, 0.95, 1.15, and 1.43) on the lean blowoff limits. It was seen that at higher Ф0, the blowoff equivalence ratio of flames with lower swirl levels was typically more sensitive to bulk flow velocities than flames stabilized at lower Ф0. The blowoff Ф of flames stabilized at higher swirl levels did not vary much with an increase in bulk flow velocity. Global CH* chemiluminescence was done to study the lean blowoff process further. At lower Ф0 and swirl levels, the occurrence of the extinction/reignition events in the shear layers seemed more prominent.
more »
« less
The Effect of Centerbody Geometry on Lean Blowoff in a Swirl-Stabilized Flame
Abstract: Lean premixed (LP) combustion systems are currently used for most modern power generation gas turbines. Though this method reduces emissions, specifically nitrogen oxides, and is more efficient than non-premixed systems, LP systems are susceptible to blowoff. The goal of this study is to find out how centerbody geometry plays a role in the lean blowoff process for swirl-stabilized flames. We find that cylindrical centerbodies have higher lean blowoff equivalence ratios than tapered centerbodies. We also find that the dominant flame shape for both centerbodies is M-shape when not anchored and tulip shaped when anchored, though the tapered centerbodies induce V-shape flames as well. The blowoff equivalence ratio and blowoff process are strongly coupled ith the flame shape.
more »
« less
- Award ID(s):
- 1749679
- PAR ID:
- 10536028
- Publisher / Repository:
- Combustion Institute
- Date Published:
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Swirl-stabilized flames are used in many gas turbine combustor configurations due to their enhanced static stability. The effects of combustor geometry, fuel composition, and bulk velocity on flame stability in swirling flows are well studied, but the effects of centerbody temperature have not been rigorously considered. The purpose of this study is to understand the impact of centerbody temperature on flame shape and dynamics. A newly instrumented variable-angle swirl-stabilized combustor was used to perform a repeatability study, and blowoff equivalence ratio was measured at centerbody temperatures ranging from 150 to 350°C and bulk velocities ranging from 16 to 55 m/s. Blowoff equivalence ratio generally decreases with centerbody temperature. Two structures were observed during blowoff: a cone shape and flame chugging. Blowoff equivalence ratio was consistently lower when the cone structure occurred, though the mechanism that excites these behaviors is still under investigation.more » « less
-
Soot formation is quantified in detail (volume fraction, particle size, number concentration, and light emissivity dispersion exponent) in a series of partially premixed counterflow flames of ethylene at equivalence ratios equal to 6.5, 5.0, and 4.0, and with maximum temperature spanning approximately 200 K. The focus is to investigate the effect of peak temperature and equivalence ratio on soot formation while maintaining constant global strain and stoichiometric mixture fraction. Oxygen is progressively displaced from the oxidizer to the fuel stream of a diffusion flame to stabilize partially premixed flames of decreasing, showing a double-flame structure consisting of a rich premixed flame component stabilized on the fuel side of the stagnation plane and a diffusion flame component stabilized on the oxidizer side. Soot is detected in the region sandwiched between the two flame components, is formed in both of them, and is convected away radially at the Particle Stagnation Plane (PSP). At fixed , raising the peak temperature invariably raises the soot volume fraction throughout the probed region. Vice versa, at fixed peak temperature, lowering the equivalence ratio causes the premixed flame component to shift away from the diffusion flame component, with the consequent broadening of the soot forming region and an increase in both soot volume fraction as well as soot particle sizes through an enhancement of surface growth. Detailed probing of the region in the vicinity of the PSP offers evidence of soot oxidation from molecular oxygen. Furthermore, when the maximum temperature is sufficiently low, the net soot production rate turns negative because surface oxidation overwhelms surface growth. Comparing the soot number production rate inferred from experiments to the dimerization rate of benzene, naphthalene, and pyrene reveals that only the smallest aromatics are present in flames at sufficiently large concentrations to account for soot nucleation. This observation applies to both the diffusion flame and the premixed flame components and confirms previous findings in strictly diffusion flames.more » « less
-
This work describes and tests the calibration process of the chemical-diffusive model (CDM) for the simulation of non-premixed diffusion flames. The CDM is an alternative, simplified approach for incorporating the effects of combustion in a fluid simulation, based on the ideas of regulating the rate of energy release such that the properties of combustion waves (e.g. flames and detonations) are reproduced. Past implementations of the CDM have considered single-stoichiometry fuel-air mixtures or mixtures with variable stoichiom- etry but with premixed modes of combustion. In this work, the CDM is tested and shown to work for non-premixed, low-Mach-number flames (i.e., diffusion flames) by incorporat- ing it into a numerical model which solves the reactive and compressible Navier-Stokes equations with the barely implicit correction (BIC) algorithm, which removes the acoustic limit on the integration time-step size. Simulations of one-dimensional premixed laminar flames reproduce the required premixed laminar flame speed, thickness, and temperature. A two-dimensional, steady-state, laminar coflow diffusion flame is computed, and the result demonstrates the ability of the algorithm to compute a non-premixed flame. Lastly, a two- dimensional simulation of two opposing jets of fuel and air show that the CDM approach can compute the structure of a counter-flow diffusion flame.more » « less
-
The study of fuel chemistry and soot inception in non-premixed combustion can be advanced by characterizing flame configurations in which the advection and diffusion transport can be finely controlled, with the ability to decouple pyrolysis from oxidation. Also, the ideal flames to be investigated should be perturbed minimally by probes and thick enough for sampling techniques to yield spatially resolved measurements of their structure. The Planar Mixing Layer Flame (PMLF) configuration introduced herein is established between a fuel and an oxidizer slot jet adjacent to each other and shielded from the ambient air by annularly co-flowing inert nitrogen. The PMLF flow is kept laminar and steady by an impinging flat plate equipped with a rectangular exhaust slit opening which anchors the position of the hot combustion products via buoyancy. The PMLF is accessible to sampling and its flow stability is preserved when using any tested probe. The experiments are complemented with 2DComputational Fluid Dynamics (CFD) modeling with detailed chemical kinetics. The results demonstrate that the PMLF has a self-similar boundary layer structure whose horizontal cross-sections are equivalent to properly selected and equally thick 1D- Counterflow Flames (CFs). The equivalence allows for excellent predictions of the PMLF thermochemical structure characterized experimentally but at a small fraction of the 2D-CFD computational cost. The 1D-CF equivalence affects even aromatics less than twofold despite their kinetics being known to be very sensitive to the temperature field. Importantly, the PMLF thickness is several millimeters and grows at increasing HABs so that the equivalent 1D-CFs have strain rates as small as 7.0 /s which cannot be studied in CF experiments. As a result, the PMLF emerges as a promising canonical non-premixed flame configuration for studying flame chemistry and soot inception on time scales of tens of milliseconds typical of many combustion applications.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Conference Paper:
- The DOI is not currently available.
