Single-phase body-centered cubic (bcc) refractory medium- or high-entropy alloys can retain compressive strength at elevated temperatures but suffer from extremely low tensile ductility and fracture toughness. We examined the strength and fracture toughness of a bcc refractory alloy, NbTaTiHf, from 77 to 1473 kelvin. This alloy’s behavior differed from that of comparable systems by having fracture toughness over 253 MPa·m1/2, which we attribute to a dynamic competition between screw and edge dislocations in controlling the plasticity at a crack tip. Whereas the glide and intersection of screw and mixed dislocations promotes strain hardening controlling uniform deformation, the coordinated slip of <111> edge dislocations with {110} and {112} glide planes prolongs nonuniform strain through formation of kink bands. These bands suppress strain hardening by reorienting microscale bands of the crystal along directions of higher resolved shear stress and continually nucleate to accommodate localized strain and distribute damage away from a crack tip.
FeCrAl cladding is one of the candidate materials for the near‐term accident‐tolerant fuel technologies under development. Research on high‐temperature mechanical behaviors of single‐crystal FeCrAl alloy is rather limited. Previous studies have reported the mechanical property of low‐index orientation in single‐crystal FeCrAl alloy at room temperature. However, the critical resolved shear stress to activate slip systems can be orientation and temperature dependent. Here, single‐crystal grains in a coarse‐grained FeCrAl alloy with different crystallographic orientations are selected to preferentially activate {110}<111> slip systems or {112}<111> slip systems. Micropillars are fabricated in the selected single‐crystal grains and tested at elevated temperatures in situ in a scanning electron microscope. The critical resolved shear stresses of {110}<111> slip systems and {112}<111> slip systems are determined at various temperatures. The critical resolved shear stress shows a temperature dependence and orientation independence. This study provides important insight for understanding the deformation mechanisms of FeCrAl alloys at elevated temperatures.
more » « less- PAR ID:
- 10536647
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Advanced Engineering Materials
- Volume:
- 26
- Issue:
- 21
- ISSN:
- 1438-1656
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
-
more » « less
Bulk, polycrystalline (Co, Cu, Mg, Ni, Zn)O was synthesized using solid-state sintering. Micropillars were prepared and mechanically deformed along three crystallographic orientations: (001), (101), and (111). Pillars (001) and (111) cracked, while Pillar (101) remained intact. Pillars (001) and (101) exhibited activated slip systems, confirmed by a large stress drop, and the presence of slip bands, respectively. Schmid factor (SF) analysis was performed to examine the effect of grain orientations on dislocation activity and slip behavior. SF values range from 0 to 0.5, with non-zero values indicating potential for slip. Six slip systems exist in the (Co, Cu, Mg, Ni, Zn)O rock salt crystal structure: 1/2⟨110⟩11¯0. For the (001) orientation, four slip systems are potentially active (SF = 0.5). For the (101) orientation, there are four potentially active slip systems (SF = 0.25). For the (111) orientation, no potentially active slips systems exist (SF = 0). Dislocation structures, which were observed post-compression via transmission electron microscopy, demonstrated variations in size, number, and distribution across the pillar, depending on micropillar orientation. Entangled dislocations created misorientation in Pillar (001), which led to the possible formation of subgrains, while singular dislocations were observed in Pillar (101), and a lack of dislocations was observed in Pillar (111). Zener–Stroh type dislocation entanglement-mediated cracking is the proposed cause of the transgranular-type cracks in Pillar (001). The possible subgrain formation, or lack of formation, respectively, caused intergranular-type cracks to additionally form in Pillar (001), while Pillar (111) only exhibited transgranular-type brittle fracture. In combination, these findings highlight the importance of dislocation activity, without the need for elevated temperature, and grain orientation in controlling the mechanical deformation response in single-phase (Co, Cu, Mg, Ni, Zn)O.
-
more » « less
The emerging class of multi-principal element alloy (MPEA) processes superior mechanical properties and has great potential for applications in extreme environments. In this work, the synergic effect of the Cr content and crystallographic orientation on the deformation behaviors of single-crystal CrCoFeNi MPEAs has been investigated by atomistic simulations. We have found distinct differences in dislocation activities, deformation microstructures, and mechanical behaviors in the model MPEAs, which depend on crystallographic orientations, Cr concentration, and the number of activated slip systems. When multiple slip systems are triggered along [100] and [111] orientations, Shockley partial activation and their interaction are predominant, leading to the formation of sessile dislocations and a dense dislocation network. When only two slip systems of Shockley partials are favored along the [110] direction, the influence of Cr concentration and planner defect energies emerges. At low Cr concentration, the double planar slip of Shockley partials results in deformation-induced nanotwins. At high Cr concentration, the partial dislocations of a single slip plane become dominant, attaining the highest volume fraction of deformation-induced phase transformation. The results provide a fundamental understanding of deformation mechanisms in MPEAs, elucidating the synergic effect of crystal orientation and composition on tunning the mechanical behaviors.
-
Sinnott, Susan (Ed.)Single crystalline sapphire (-) possesses superior mechanical, thermal, chemical, and optical properties over a wide range of temperatures and pressure conditions, allowing it for a broad spectrum of industrial applications. For the past few decades, research has aimed at comprehensive understanding of its plastic deformation mechanisms under mechanical loading. In this study, we have employed molecular dynamics (MD) simulations to study rhombohedral twinning of sapphire, which is of critical importance in understanding the plastic deformation of sapphire as one of most commonly observed deformation modes. Since the critical resolved shear stress (CRSS) plays a pivotal role in describing the activation of slip systems, it is adopted in this study as the key parameter for analysis. The CRSS is calculated during the uniaxial compression test of a cubic sapphire crystal, oriented to exclusively activate rhombohedral twinning deformation, under simulation conditions such as temperature, strain rate, and system size. Furthermore, a theoretical model of CRSS is constructed based on theories of thermal activation processes, then empirically fitted to CRSS data gathered from the MD simulations. This model accurately captures the relationships between CRSS and external parameters including temperature, strain rate, and system size and shows excellent agreements with the simulation results.more » « less
-
The seismic anisotropy of the Earth’s solid inner core has been the topic of much research. It could be explained by the crystallographic preferred orientation (CPO) developing during convection. The likely phase is hexagonal close-packed iron (hcp), alloyed with nickel and some lighter elements. Here we use high energy synchrotron X-rays to study CPO in Fe-9wt%Si, uniaxially compressed in a diamond anvil cell in radial geometry. The experiments reveal that strong preferred orientation forms in the low-pressure body-centred cubic (bcc) phase that appears to be softer than pure iron. CPO is attributed to dominant {110}<111>slip. The onset of the bcc→hcp transition occurs at a pressure of ≈15 GPa, and the alloy remains in a two phase bcc+hcp state up to 40 GPa. The hcp phase forms first with a distinct {11¯20} maximum perpendicular to compression. Modelling shows that this is a transformation texture, which can be described by Burgers orientation relationship with variant selection. Experimental results suggest that bcc grains oriented with <100> parallel to compression transform into hcp first. The CPO of the hcp changes only slowly during further pressure and deviatoric stress increase at ambient temperature. After heating to 1600 K, a change in the hcp CPO is observed with alignment of (0001) planes perpendicular to compression that can be interpreted as dominant (0001)<11¯20> slip, combined with {10¯12}<¯1011> mechanical twinning, which is similar to the deformation modes suggested previously for pure hcp iron at inner core conditions.more » « less
