Attention:The NSF Public Access Repository (PAR) system and access will be unavailable from 11:00 PM ET on Thursday, November 12th until 12:00 AM ET on Friday, November 13th due to maintenance. We apologize for the inconvenience.


Title: Molecular aspect ratio effect on axial thermal transport in solution-spun carbon nanotube fibers
Neat, densely packed, and highly aligned carbon nanotube fibers (CNTFs) have appealing room-temperature axial thermal conductivity (k) and thermal diffusivity (α) for applications in lightweight heat spreading, flexible thermal connections, and thermoelectric active cooling. Although CNTFs are regularly produced from different input carbon nanotubes (CNTs), prior work has not quantified how the CNT molecular aspect ratio r (i.e., molecular length-to-diameter ratio) influences k and α in well-aligned, packed CNTFs. Here, we perform self-heated steady-state and three-omega thermal measurements at room temperature on CNTF suspended in vacuum. Our results show that k increases from 150 to 380W/mK for viscosity-averaged molecular aspect ratios increasing from r=960 to 5600 and nanotube diameters of ∼2 nm, which we attribute to the effects of thermal resistances between CNT bundles. CNTFs made with varying volume fraction ϕ of constituent high-r and low-r CNT have properties that fall within or below the typical macroscopic rule-of-mixtures bounds. The thermal diffusivity α scales with k, leading to a sample-averaged volumetric heat capacity of 1.5±0.3MJ/m3K. This work's findings that fibers made from longer CNT have larger k and α at room temperature motivate further investigation into thermal transport in solution-spun CNTF.  more » « less
Award ID(s):
2230727
PAR ID:
10598172
Author(s) / Creator(s):
; ; ; ; ; ; ; ;
Publisher / Repository:
AIP publishing
Date Published:
Journal Name:
Journal of Applied Physics
Volume:
137
Issue:
10
ISSN:
0021-8979
Subject(s) / Keyword(s):
Sponsoring Org:
National Science Foundation
More Like this
  1. Abstract Vacuum generally suppresses gaseous heat conduction without altering intrinsic transport of solid materials. Here we report an unexpected, time-dependent increase in thermal diffusivity (α) of lignin-based carbon fibers (CFs) during vacuum exposure. At <0.08 Pa, α increases by up to ∼95% and approaches saturation, while its electrical resistance (R) shows smaller, condition-dependent changes. After ∼16 h of air re-exposure, α partially or nearly fully recovers, while R responds less consistently, demonstrating strong dependence on exposure history. Across the vacuum systems examined, the α increase diminishes as vacuum pressure rises from <0.08 to 2.13 Pa, whereas a moderate temperature rise (∼50 K) accelerates the evolution of the α increase under ∼0.21 Pa vacuum. Laser-power-normalized Raman intensities increase during air re-exposure without significant D- or G-band shifts, providing indirect evidence of reversible near-surface-state evolution rather than restructuring of the carbon framework. Atomistic simulations show that adsorbed water shortens acoustic phonon lifetimes and suppresses in-plane thermal transport. These results support vacuum-induced desorption of near-surface adsorbates as reducing phonon scattering and increasing α, as there is negligible change in volumetric heat capacity. Removal of humidity-assisted charge-transport pathways may also contribute to the increase in R observed in some sequences. It is concluded that the exposure history is an important factor in thermal and electrical measurements of carbon fibers under vacuum. 
    more » « less
  2. Additive manufacturing (AM) as a disruptive technique has offered great potential to design and fabricate many metallic components for aerospace, medical, nuclear, and energy applications where parts have complex geometry. However, a limited number of materials suitable for the AM process is one of the shortcomings of this technique, in particular laser AM of copper (Cu) is challenging due to its high thermal conductivity and optical reflectivity, which requires higher heat input to melt powders. Fabrication of composites using AM is also very challenging and not easily achievable using the current powder bed technologies. Here, the feasibility to fabricate pure copper and copper-carbon nanotube (Cu-CNT) composites was investigated using laser powder bed fusion additive manufacturing (LPBF-AM), and 10 × 10 × 10 mm3 cubes of Cu and Cu-CNTs were made by applying a Design of Experiment (DoE) varying three parameters: laser power, laser speed, and hatch spacing at three levels. For both Cu and Cu-CNT samples, relative density above 90% and 80% were achieved, respectively. Density measurement was carried out three times for each sample, and the error was found to be less than 0.1%. Roughness measurement was performed on a 5 mm length of the sample to obtain statistically significant results. As-built Cu showed average surface roughness (Ra) below 20 µm; however, the surface of AM Cu-CNT samples showed roughness values as large as 1 mm. Due to its porous structure, the as-built Cu showed thermal conductivity of ~108 W/m·K and electrical conductivity of ~20% IACS (International Annealed Copper Standard) at room temperature, ~70% and ~80% lower than those of conventionally fabricated bulk Cu. Thermal conductivity and electrical conductivity were ~85 W/m·K and ~10% IACS for as-built Cu-CNT composites at room temperature. As-built Cu-CNTs showed higher thermal conductivity as compared to as-built Cu at a temperature range from 373 K to 873 K. Because of their large surface area, light weight, and large energy absorbing behavior, porous Cu and Cu-CNT materials can be used in electrodes, catalysts and their carriers, capacitors, heat exchangers, and heat and impact absorption. 
    more » « less
  3. The authors reveal a thermal actuating bilayer that undergoes reversible deformation in response to low-energy thermal stimuli, for example, a few degrees of temperature increase. It is made of an aligned carbon nanotube (CNT) sheet covalently connected to a polymer layer in which dibenzocycloocta-1,5-diene (DBCOD) actuating units are oriented parallel to CNTs. Upon exposure to low-energy thermal stimulation, coordinated submolecular-level conformational changes of DBCODs result in macroscopic thermal contraction. This unique thermal contraction offers distinct advantages. It’s inherently fast, repeatable, low-energy driven, and medium independent. The covalent interface and reversible nature of the conformational change bestow this bilayer with excellent repeatability, up to at least 70 000 cycles. Unlike conventional CNT bilayer systems, this system can achieve high precision actuation readily and can be scaled down to nanoscale. A new platform made of poly(vinylidene fluoride) (PVDF) in tandem with the bilayer can harvest low-grade thermal energy and convert it into electricity. The platform produces 86 times greater energy than PVDF alone upon exposure to 6 °C thermal fluctuations above room temperature. This platform provides a pathway to low-grade thermal energy harvesting. It also enables low-energy driven thermal artificial robotics, ultrasensitive thermal sensors, and remote controlled near infrared (NIR) driven actuators. 
    more » « less
  4. The authors reveal a thermal actuating bilayer that undergoes reversible deformation in response to low-energy thermal stimuli, for example, a few degrees of temperature increase. It is made of an aligned carbon nanotube (CNT) sheet covalently connected to a polymer layer in which dibenzocycloocta-1,5-diene (DBCOD) actuating units are oriented parallel to CNTs. Upon exposure to low-energy thermal stimulation, coordinated submolecular-level conformational changes of DBCODs result in macroscopic thermal contraction. This unique thermal contraction offers distinct advantages. It's inherently fast, repeatable, low-energy driven, and medium independent. The covalent interface and reversible nature of the conformational change bestow this bilayer with excellent repeatability, up to at least 70 000 cycles. Unlike conventional CNT bilayer systems, this system can achieve high precision actuation readily and can be scaled down to nanoscale. A new platform made of poly(vinylidene fluoride) (PVDF) in tandem with the bilayer can harvest low-grade thermal energy and convert it into electricity. The platform produces 86 times greater energy than PVDF alone upon exposure to 6 °C thermal fluctuations above room temperature. This platform provides a pathway to low-grade thermal energy harvesting. It also enables low-energy driven thermal artificial robotics, ultrasensitive thermal sensors, and remote controlled near infrared (NIR) driven actuators. 
    more » « less
  5. Electronic system layouts have increasingly become smaller and more compact. To address the growing demand for performance, dynamic thermal management with thermal energy storage has emerged as an attractive solution. Phase change materials (PCM) can store and release large amounts of heat through melting or solidification. However, they are limited by their thermal conductivity, which is several orders of magnitude lower than traditional heat sinks. To address this design weakness, we have developed a novel composite consisting of vertically aligned carbon nanotube arrays infiltrated with PCM to deliver a high thermal conductivity storage medium that also maintains the high latent heat capacity of the native PCM. This study numerically and experimentally investigates the design of an encapsulated CNT-PCM composite and its impact on the temperature rise and peak temperature of an electronic device. Different form factors have been experimentally tested. The composite's impact on a heating element is measured experimentally, and a numerical model is developed and verified using the experimental results. Additional models are designed to evaluate the effect of composite thickness on thermal response. 
    more » « less