An official website of the United States government
Within the last two-million years, subduction has initiated at the southern end of the New Hebrides trench along the ~E-W trending Matthew-Hunter section of the trench (Patriat et al., 2015; 2019). This part of the subduction system originated as a subduction-transform edge propagator (STEP) fault, a transcurrent plate boundary that terminates Australian plate subduction at the southern end of the New Hebrides trench at a slab tear and allows its rapid southwestward rollback (Govers and Wortel, 2005). The down warped torn lithospheric edge of the STEP fault dips northward in the same direction as the absolute plate motion of the Australian plate in a hotspot reference frame. This creates a strong southward mantle flow (~55 km/Myr) against the already failed and weak northward dipping STEP fault, promoting further down bending and subduction. Through this mechanism, subduction and southward rollback of the STEP fault edge has begun, initiating a subduction zone in an extensional stress regime without requiring initial convergence between the Australian plate and the North Fiji Basin. In fact, the North Fiji Basin is in extension, forming rifts and spreading centers and volcanically accreting crust unusually close to the Matthew-Hunter trench. Subduction initiation at the Matthew-Hunter trench has effectively terminated the STEP fault and slab tear, so that subduction now takes place continuously around the corner from the New Hebrides to the Matthew-Hunter section of the trench. This model proposes that STEP faults are favorable tectonic boundaries for subduction initiation, provided that mantle flow induced by absolute plate motion is oriented correctly, as shown by the opposing example of the Tonga step fault, which displays no evidence of initiating subduction despite a much larger lithospheric age contrast (Martinez, 2024). Govers, R., and M. J. R. Wortel (2005), Lithosphere tearing at STEP faults: Response to edges of subduction zones, Earth and Planetary Science Letters, 236, 505-523. Martinez, F. (2024), Subduction initiation (or not) due to absolute plate motion at STEP faults: The New Hebrides vs. the Tonga examples, in EGU General Assembly 2024, Vienna, Austria, https://doi.org/10.5194/egusphere-egu24-4189 Patriat, M., et al. (2015), Propagation of back-arc extension into the arc lithosphere in the southern New Hebrides volcanic arc, G-Cubed, 16(9), 3142-3159.Patriat, M., et al. (2019), Subduction initiation terranes exposed at the front of a 2 Ma volcanically-active subduction zone, Earth and Planetary Science Letters, 508, 30-40.
more »
« less
This content will become publicly available on January 20, 2026
Subduction initiation (or not) due to absolute plate motion at STEP faults: The New Hebrides vs. the Tonga examples
Subduction initiation remains one of the least understood global processes of plate tectonics. Prominent models have been cast in terms of two broad classes: spontaneous cases due to lithospheric gravitational instabilities and induced cases due to forced plate convergence. Yet gravitationally unstable lithosphere is old, strong, and difficult to begin to bend into a subduction zone and convergent forces necessary to begin subduction are often too large given the plates involved. These models also consider the asthenospheric mantle as passive, even though relative motion between slabs and the asthenosphere has long been regarded as a strong control on subduction dynamics. Here I propose that subduction-transform edge propagator (STEP) faults can initiate subduction depending on the absolute motion of the STEP fault with respect to the asthenosphere. STEP faults form where subduction zones end and the subducting plate tears forming a down flexed transcurrent plate boundary at the surface shearing against the adjacent rear arc lithospheric plate. However, STEP faults are not simple transcurrent boundaries. Absolute motion of the down flexed STEP fault edge with respect to the surrounding asthenosphere can produce a strong sea anchor force that either continues to bend the edge downward, initiating subduction, or opposes slab bending, inhibiting subduction. In the south Pacific, the southern end of the New Hebrides Trench and the northern end of the Tonga Trench are type-example STEP faults with opposite senses of dip but both moving northward with respect to the asthenosphere. The northward dipping New Hebrides STEP fault moves northward in a mantle reference frame creating a strong asthenospheric flow against the STEP fault edge, inducing active subduction at the Matthew-Hunter trench. In contrast, the Tonga STEP fault dips southward but also has a northward component of motion with respect to the mantle. Asthenosphere thus flows southward beneath the down flexed Tonga STEP fault edge opposing further bending. Subduction does not initiate at the Tonga STEP fault despite a ~100 Myr age contrast between the Pacific and north Fiji and Lau basin lithospheres. Since absolute plate motions reflect the sum of all forces acting on the entire lithospheric plate, a strong sea anchor mantle force may be generated at a STEP fault edge, initiating subduction (or inhibiting it), even where lithosphere is old, strong, and resists bending and without requiring large convergent forces between plates, overcoming these objections to previous models.
more »
« less
- Award ID(s):
- 2228414
- PAR ID:
- 10599722
- Publisher / Repository:
- European Geosciences Union General Assembly 2024
- Date Published:
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract Oceanic plates experience extensive normal faulting as they bend and subduct, enabling fracturing of the incoming lithosphere. Debate remains about the relative importance of pre‐existing faults, plate curvature and other factors controlling the extent and style of bending‐related faulting. The subduction zone off the Alaska Peninsula is an ideal place to investigate controls on bending faulting as the orientation of the abyssal‐hill fabric with respect to the trench and plate curvature vary along the margin. Here, we characterize faulting between longitudes 161°W and 155°W using newly collected multibeam bathymetry data. We also use a compilation of seismic reflection data to constrain patterns of sediment thickness on the incoming plate. Although sediment thickness increases over 1 km from 156°W to 160°W, most sediments were deposited prior to the onset of bending faulting and thus should have limited impact on the expression of bend‐related fault strikes and throws in bathymetry data. Where magnetic anomalies trend subparallel to the trench (<30°) west of ∼156°W, bending faults parallel magnetic anomalies, implying that bending faults reactivate pre‐existing structures. Where magnetic anomalies are highly oblique (>30°) to the trench east of 156°W, no bending faults are observed. Summed fault throws increase to the west, including where pre‐existing structure orientations are constant (between 157 and 161°W), suggesting that another factor such as the increase in slab curvature must influence bending faulting. However, the westward increase in summed fault throws is more abrupt than expected for gradual changes in slab bending alone, suggesting potential feedbacks between pre‐existing structures, slab dip, and faulting.more » « less
-
We utilized shear wave splitting analysis of teleseismic SKS, SKKS, and PKS phases to infer upper mantle deformational fabrics across a substantial area of Southeast Asia, where splitting measurements were previously limited. We used newly available permanent and temporary broadband seismic networks deployed across the Indo-Burma subduction zone and the eastern Indochina peninsula. The resulting 492 well-constrained splitting and 654 null measurements from 185 stations reveal clear large-scale patterns in the mantle deformational fabrics in response to the highly oblique active subduction and a large transform plate boundary. We identified two distinct domains of mantle deformation fabrics in the western Burma microplate and the eastern Indochina peninsula. In the former, trench parallel N-S fast polarization directions with an average lag time (δt) of 1.9 s are observed beneath the Indo-Burman Ranges. We suggest the observed splitting is partly due to anisotropy in the sub-slab region and relates to shear induced by the north moving Indian plate. The lithospheric fabric within the Indo-Burman Ranges and underlying subducting slab fabric contribute to produce the observed average δt of 1.9 s. The δt value decreases to an average of 1.0 s towards the back-arc until we reach the dextral Sagaing fault. In the second domain, starting approximately 100 km east of the Sagaing fault, we observe a consistent E-W fast direction with an average δt of 1.10 s in the eastern Shan-Thai and Indochina blocks. We interpret the E-W fabric as due to the deformation associated with the westward spreading of the Hainan mantle plume, possibly driven by overriding plate motion. Low velocities in the shallow mantle and late Cenozoic intraplate volcanism in this region support the plume-driven asthenospheric flow model in the Indochina peninsula. The sudden transition of the fast polarization direction from N-S to E-W along the eastern edge of the Burma microplate indicates the Sagaing fault acts as a mantle flow boundary between the subduction dominated trench parallel flow to the west and plume induced asthenospheric flow to the east. We also observed no net splitting beneath the Bengal basin which is most likely due to the presence of frozen vertical fabric resulting from the Kerguelen plume activity during Early Cretaceous.more » « less
-
Abstract Age-progressive seamount tracks generated by lithospheric motion over a stationary mantle plume have long been used to reconstruct absolute plate motion (APM) models. However, the basis of these models requires the plumes to move significantly slower than the overriding lithosphere. When a plume interacts with a convergent or divergent plate boundary, it is often deflected within the strong local mantle flow fields associated with such regimes. Here, we examined the age progression and geometry of the Samoa hotspot track, focusing on lava flow samples dredged from the deep flanks of seamounts in order to best reconstruct when a given seamount was overlying the mantle plume (i.e., during the shield-building stage). The Samoan seamounts display an apparent local plate velocity of 7.8 cm/yr from 0 to 9 Ma, 11.1 cm/yr from 9 to 14 Ma, and 5.6 cm/yr from 14 to 24 Ma. Current fixed and mobile hotspot Pacific APM models cannot reproduce the geometry of the Samoa seamount track if a long-term fixed hotspot location, currently beneath the active Vailulu’u Seamount, is assumed. Rather, reconstruction of the eruptive locations of the Samoan seamounts using APM models indicates that the surface expression of the plume migrated ~2° northward in the Pliocene. Large-scale mantle flow beneath the Pacific Ocean Basin cannot explain this plume migration. Instead, the best explanation is that toroidal flow fields—generated by westward migration of the Tonga Trench and associated slab rollback—have deflected the conduit northward over the past 2–3 m.y. These observations provide novel constraints on the ways in which plume-trench interactions can alter hotspot track geometries.more » « less
-
Abstract Shear wave splitting is often assumed to be caused by mantle flow or preexisting lithospheric fabrics. We present 2,389 new SKS shear wave splitting observations from 384 broadband stations deployed in Alaska from January 2010 to August 2017. In Alaska, splitting appears to be controlled by the absolute plate motion (APM) of the North American and Pacific plates, the interaction between the two plates, and the geometry of the subducting Pacific‐Yakutat plate. Outside of the subduction zone's influence, the fast directions in northern Alaska parallel the North American APM direction. Fast directions near the Queen Charlotte‐Fairweather transform margin are parallel to the faults and are likely caused by the strike‐slip deformation extending throughout the lithosphere. In the mantle wedge, fast directions are oriented along the strike of the slab with large splitting times and are caused by along‐strike flow in the mantle wedge as the slab provides a barrier to flow. South of the Alaska Peninsula, the fast directions are parallel to the trench regardless of sea floor fabric, indicating along strike flow under the Pacific plate. Under the Kenai Peninsula, the complex flat slab geometry may cause subslab flow to be parallel to Pacific APM direction or to the North America‐Pacific relative motion.more » « less
