An official website of the United States government
Abstract The effect of nanoconfinement on the kinetics of benzyl methacrylate radical polymerization is investigated using differential scanning calorimetry. Controlled pore glass (CPG), ordered mesoporous carbons, and mesoporous silica are used as confinement media with pore sizes from 2 to 8 nm. The initial polymerization rate in CPG and mesoporous silica increases relative to the bulk and increases linearly with reciprocal pore size; whereas, the rate in the carbon mesopores decreases linearly with reciprocal pore size; the changes are consistent with the rate being related to the ratio of the pore surface area to pore volume. Induction times are longer for nanoconfined polymerizations, and in the case of CPG and carbon mesopores, autoacceleration occurs earlier, presumably due to the limited diffusivity and lower termination rates for the confined polymer chains. The molecular weight of the polymer synthesized in the nanopores is generally higher than that obtained in the bulk except at the lowest temperatures investigated. The equilibrium conversion under nanoconfinement decreases with decreasing temperature and with confinement size, exhibiting what appears to be a floor temperature at low temperatures.
more »
« less
This content will become publicly available on October 28, 2026
Molar-Mass-Dependent Partitioning of Polyethylene in Nanopores of Model Catalyst Supports from Small-Angle Neutron Scattering
Heterogeneous catalysis offers opportunities to enhance valorization of plastic waste via chemical recycling through control of the upcycled product distributions. Minimizing low-value light hydrocarbons is desired; however, fundamental insights into how to control selectivity are lacking. Here we use contrast variation with small-angle neutron scattering (SANS), model perdeuterated polyethylenes (dPEs), and a model liquid hydrocracking product (tetradecane) to quantify polymer partitioning within mesoporous silica (SBA-15). Polyethylene concentration within the mesopores is increased relative to the bulk solution, and this partitioning increases as the temperature increases. However, this polyethylene partitioning is maximized when the radius of gyration of the polymer chains is comparable to the SBA-15 pore size (10 nm). An increased partitioning at higher temperatures is attributed to entropically driven adsorption of PE within the mesopores. There is no observed preferential partitioning of hexatriacontane (a model oligomer) within the mesopores at the temperatures examined. These results suggest that pore size could promote the selective partitioning of polymer species into the mesopores by size. For plastic upcycling, pore-size-dependent partitioning should increase the probability for the reaction of long polymers over oligomeric and small-molecule polyolefin depolymerization products.
more »
« less
- Award ID(s):
- 2229168
- PAR ID:
- 10665519
- Publisher / Repository:
- ACS Publications
- Date Published:
- Journal Name:
- Langmuir
- Volume:
- 41
- Issue:
- 42
- ISSN:
- 0743-7463
- Page Range / eLocation ID:
- 28424 to 28433
- Format(s):
- Medium: X
- Associated Dataset(s):
- View Associated Dataset(s) >>
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Biomass is a renewable carbon feedstock that can be converted to 5-hydroxymethylfurfural (HMF), a useful platform chemical that can be modified to produce valuable chemicals and fuels. Previous research has shown that high HMF selectivity can be achieved in organic solvents such as dimethyl sulfoxide (DMSO) because of its capability to stabilize HMF in solution, but DMSO is an undesirable solvent to use industrially as product separation from the reaction solution is difficult. Surface functionalization of porous catalysts has been shown as a method to introduce solvent-effects at the surface of heterogeneous catalysts, thus avoiding the need for high boiling solvents like DMSO. Poly(ethylene sulfoxide) (PESO) is added to the surface of sulfonic acid (SA) functionalized SBA-15 silica to obtain the bifunctional catalyst SA-PESO-SBA-15. Co-localization of the sulfoxide polymer with sulfonic acid groups inside the catalyst pores (SA-PESO-SBA-15) increased HMF selectivity to 51% from 26% obtained by monofunctional SA-SBA-15 at 27% fructose conversion in water. Additionally, this bifunctional catalyst performs best in 4 : 1 (w/w) THF : water cosolvent, a more industrially preferred cosolvent system, obtaining 79% HMF selectivity at 87% fructose conversion. Overall, these materials are promising for the selective conversion of fructose to HMF.more » « less
-
Abstract The hydrogenolysis of polymers is emerging as a promising approach to deconstruct plastic waste into valuable chemicals. Yet, the complexity of plastic waste, including multilayer packaging, is a significant barrier to handling realistic waste streams. Herein, we reveal fundamental insights into a new chemical route for transforming a previously unaddressed fraction of plastic waste – poly(ethylene‐co‐vinyl alcohol) (EVOH) and related polymer blends – into alkane products. We report that Ru/ZrO2is active for the concurrent hydrogenolysis, hydrogenation, and hydrodeoxygenation of EVOH and its thermal degradation products into alkanes (C1−C35) and water. Detailed reaction data, product analysis, and catalyst characterization reveal that the in‐situ thermal degradation of EVOH forms aromatic intermediates that are detrimental to catalytic activity. Increased hydrogen pressure promotes hydrogenation of these aromatics, preventing catalyst deactivation and improving alkane product yields. Calculated apparent rates of C−C scission reveal that the hydrogenolysis of EVOH is slower than low‐density polyethylene. We apply these findings to achieve hydrogenolysis of EVOH/polyethylene blends and elucidate the sensitivity of hydrogenolysis catalysts to such blends. Overall, we demonstrate progress towards efficient catalytic processes for the hydroconversion of waste multilayer film plastic packaging into valuable products.more » « less
-
Only a small fraction of the plastics produced is being recycled, with the great majority landfilled or released into the environment. Mechanical recycling is currently used to recycle plastic, however, this method is efficient only for homogeneous and non-contaminated feedstock, and for easily identifiable objects such as bottles made of PET or HDPE. Notably, mechanical recycling cannot easily handle plastic films which constitute about 40% of all plastic packaging used. Polyolefins in the plastic waste stream can be processed via pyrolysis, the most common among chemical recycling processes. Pyrolysis, however, decomposes the polymers, resulting in undesirable greenhouse gas (GHG) emissions. Further, pyrolysis is not viewed as constituting recycling when its product, pyrolysis oil, is not converted into new polymers.Plastics recycling research in our group utilizes physical, solvent-based processes that do not break down the polymer chains. This constitutes true recycling, as the recovered polymer is the same as the starting material. Such molecular recycling processes leave the polymer chains intact, thus maintaining their embodied energy and emitting relatively little GHG.Examples on molecular recycling are highlighted on the (i) separation of polyolefin mixtures through dissolution/precipitation in solvents that switch between a form that dissolves polyolefins and another that does not, hence facilitating the cycling and reuse of the solvent, and (ii) recovery of polyethylene from multilayer films via solvent-assisted delamination and separation, which retain the majority component, polyethylene, in the solid form, hence reducing greatly solvent amounts. The recovered polyolefins, following appropriate processing, can replace primary materials without loss of properties or performance and, hence, meet demand by customers and corporations to incorporate recycled plastics into products.more » « less
-
Confinement Effects on the Magnetic Ionic Liquid 1-Ethyl-3-methylimidazolium Tetrachloroferrate(III)Confinement effects for the magnetoresponsive ionic liquid 1-ethyl-3-methylimidazolium tetrachloroferrate(III), [C2mim]FeCl4, are explored from thermal, spectroscopic, and magnetic points of view. Placing the ionic liquid inside SBA-15 mesoporous silica produces a significant impact on the material’s response to temperature, pressure, and magnetic fields. Isobaric thermal experiments show melting point reductions that depend on the pore diameter of the mesopores. The confinement-induced reductions in phase transition temperature follow the Gibbs–Thomson equation if a 1.60 nm non-freezable interfacial layer is postulated to exist along the pore wall. Isothermal pressure-dependent infrared spectroscopy reveals a similar modification to phase transition pressures, with the confined ionic liquid requiring higher pressures to trigger phase transformation than the unconfined system. Confinement also impedes ion transport as activation energies are elevated when the ionic liquid is placed inside the mesopores. Finally, the antiferromagnetic ordering that characterizes unconfined [C2mim]FeCl4 is suppressed when the ionic liquid is confined in 5.39-nm pores. Thus, confinement provides another avenue for manipulating the magnetic properties of this compound.more » « less
