Bamboo as a natural fiber reinforced composite material possesses anisotropic mechanical properties. The highest strength and stiffness are found when bamboo was loaded along the longitudinal direction of fibers. Therefore, evaluating the elastic modulus of bamboo along its longitudinal direction is necessary for structural design. In this work, a nondestructive, dynamic testing method of free vibration was used to measure the elastic constant of bamboo in the longitudinal direction. Specimens with various lengths were tested under bending vibration conditions to determine the damped frequencies and damped periods through the Fast Fourier Transform (FFT). Then, the fundamental solution to the Euler-Bernoulli equation for free vibration was used to calculate the elastic moduli. It is found that the moduli of elasticity for specimens with various lengths were in the range from 14.1 to 16.7 GPa under two different loading configurations. The static tests by three-point bending produced elastic modulus results of as received bamboo: 14.24 ± 0.57 GPa for loading configuration 1 and 14.58 ± 0.08 GPa under loading configuration 2. The elastic moduli varied from as low as 11 to as high as 19 GPa depending on the moisture contents and testing methods. It is concluded that both static and dynamic tests delivered close elastic modulus values. The dynamic test results are slightly higher than the static ones due to the deformation rate effect. Moisture content in bamboo has significant effect on the stiffness of the composite. The higher the moisture content, the lower the stiffness of the bamboo. The overall deviation of the dynamic testing for determining the elastic modulus is about 5.74% considering the errors from geometry, density, and frequency measurements.
more »
« less
Size dependent, anisotropic deformation behaviors of Fe-SiOC columnar nanocomposites
Fe-SiOC nanocomposites with core-shell (crystal-amorphous) columnar structures exhibit size dependent, anisotropic mechanical properties. When loading along the columns, the yield strength of Fe-SiOC increases from 2.6 GPa to 3.5 GPa as the column diameter decreases from ~14.0 nm to ~3.7 nm. In contrast, the yield strength of Fe-SiOC decreases from 3.1 GPa to 2.5 GPa when the loading is perpendicular to the columns. Combining with transmission electron microscope (TEM) analysis, the anisotropic mechanical properties were attributed to the size-dependent transition of deformation mechanisms from co-deformation (Fe and SiOC) to grain boundaries mediated cracking.
more »
« less
- PAR ID:
- 10674848
- Publisher / Repository:
- elsevier
- Date Published:
- Journal Name:
- Scripta Materialia
- Volume:
- 267
- Issue:
- C
- ISSN:
- 1359-6462
- Page Range / eLocation ID:
- 116833
- Subject(s) / Keyword(s):
- Strength Size dependent Anisotropic Columnar nanocomposites
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Single-phase solid-solution refractory high-entropy alloys (HEAs) show remarkable mechanical properties, such as their high yield strength and substantial softening resistance at elevated temperatures. Hence, the in-depth study of the deformation behavior for body-centered cubic (BCC) refractory HEAs is a critical issue to explore the uncovered/unique deformation mechanisms. We have investigated the elastic and plastic deformation behaviors of a single BCC NbTaTiV refractory HEA at elevated temperatures using integrated experimental efforts and theoretical calculations. The in situ neutron diffraction results reveal a temperature-dependent elastic anisotropic deformation behavior. The single-crystal elastic moduli and macroscopic Young’s, shear, and bulk moduli were determined from the in situ neutron diffraction, showing great agreement with first-principles calculations, machine learning, and resonant ultrasound spectroscopy results. Furthermore, the edge dislocation–dominant plastic deformation behaviors, which are different from conventional BCC alloys, were quantitatively described by the Williamson-Hall plot profile modeling and high-angle annular dark-field scanning transmission electron microscopy.more » « less
-
We report compression tests on micro-pillars manufactured from bulk specimens of partially devitrified SAM25 (Fe49.7Cr17.7Mn1.9Mo7.4W1.6B15.2C3.8Si2.4). Yield strength values of ~6 GPa were obtained. Such a high strength can be attributed to the higher glass transition temperature (883 K) of this material, which impedes the multiplication of shear bands under loading, and to the presence of hard crystalline domains that result from devitrification of the amorphous powders during powder consolidation. The Vickers hardness of the specimens was found to be strongly correlated to the processing temperature and, hence to the volume of crystalline phases present in the specimens. As the processing temperature is increased, there is a reduction in free volume from the structural relaxation process in the amorphous alloy, leading to the eventual nucleation of crystalline phases of BCC Fe, Cr2B, Cr21.30Fe1.7C6, or Fe23B2C4, during the densification process. These results shed light on the relationship between nanocrystalline domains and the mechanical behavior of Fe-based amorphous/crystalline composites.more » « less
-
A facile and novel processable method to synthesize the Ni nanoparticles (Ni NPs) by tailoring their size in the matrix of the silicon oxycarbide (SiOC) ceramic system is reported. This method is based on polymer-derived ceramics (PDCs), instead of the conventional powder route. The specific structural characteristics and magnetic properties of the various Ni NPs/SiOC composites as a function of carbon content are systematically investigated. The magnetic properties are experimentally investigated as a function of NP size and measurement temperature. It is demonstrated that the change in the size of Ni NPs (average from ≈4 to ≈ 19 nm) determines the magnetic nature of superparamagnetism. Zero-field-cooled (ZFC) and field-cooled (FC) magnetization studies under magnetic fields of 100 Oe are performed. The saturated M versus H (M–H) loops (saturation magnetization) increase and the coercivity decreases with the size reduction of Ni NPs. It is an indicator of the presence of superparamagnetic behavior and single-domain NP for ceramic materials.more » « less
-
Plastic-bonded granular materials (PBM) are widely used in industrial sectors, including building construction, abrasive applications, and defense applications such as plastic-bonded explosives. The mechanical behavior of PBM is highly nonlinear, irreversible, rate dependent, and temperature sensitive governed by various micromechanical attributions such as grain crushing and binder damage. This paper presents a thermodynamically consistent, microstructure-informed constitutive model to capture these characteristic behaviors of PBM. Key features of the model include a breakage internal variable to upscale the grain-scale information to the continuum level and to predict grain size evolution under mechanical loading. In addition, a damage internal state variable is introduced to account for the damage, deterioration, and debonding of the binder matrix upon loading. Temperature is taken as a fundamental external state variable to handle non-isothermal loading paths. The proposed model is able to capture with good accuracy several important aspects of the mechanical properties of PBM, such as pressure-dependent elasticity, pressure-dependent yield strength, brittle-to-ductile transition, temperature dependency, and rate dependency in the post-yielding regime. The model is validated against multiple published datasets obtained from confined and unconfined compression tests, covering various PBM compositions, confining pressures, temperatures, and strain rates.more » « less
An official website of the United States government

