We developed a robust and systematic approach to synthesize well‐defined polyolefin bottlebrush homopolymers and block copolymers using ring‐opening metathesis polymerization (ROMP) of tailored norbornene‐functionalized highly branched polyolefin (PE) macromonomers (MMs). Pd‐diimine catalyst chelates are chosen to yield active ester chain‐end functionalized PEs from living polymerizations which are converted to norbornene‐functionalized PEs (MMs) with high control over molecular weight (Mw). From a series of MMs with molecular weights of 2.3, 5.1, 10.5, and 15.2 kg/mol, bottlebrush (BB) homopolymers with Mw of 3800, 4800, and 6400 kg/mol, as well as a bottlebrush block copolymer with a Mw of 3700 kg/mol, were synthesized and subsequently investigated. WAXS studies confirm the typical molecular BB microstructure in our BB homopolymers, where the backbone‐to‐backbone distance is a linear function of the MMs size. Linear viscoelastic measurements reveal that the BB homopolymers are ultra soft (with plateau modulus < 1.5 kPa) and have very large entanglement molecular weight (>1 Mg/mol). The presented approach establishes a pathway toward polyolefin BB with tunable properties to serve as robust but ultra‐soft adhesives with potential to be developed into soft elastomers.
more »
« less
Ultra‐High Molecular Weight Polydimethylsiloxane Bottlebrushes From Norbornene‐Pyrrolidine Capped Macromonomers
ABSTRACT Bottlebrush (BB) polymers with polydimethylsiloxane (PDMS) side‐chains exhibit supersoft moduli (E < 100 kPa) without solvent, making them promising tissue‐mimetic materials for biomedical applications. While larger backbones and side‐chains enhance softness, synthetic limitations have constrained their molecular weight. We report a graft‐through method to access ultra‐high molecular weight PDMS BB polymers (~1–20 million g mol−1). Central to this was the design of a norbornene‐pyrrolidine aryllithium initiator for the anionic ring‐opening of hexamethylcyclotrisiloxane (D3), yielding monofunctionalized PDMS macromonomers (MMs) with molecular weights from 1–30 kg mol−1. Subsequent ring‐opening metathesis polymerization (ROMP) produced BB homopolymers within minutes (t ≤ 5 min) and with low dispersity (Đ < 1.3). The ‐C‐Si‐O‐ linkage between the backbone and side‐chains provided improved chemical stability over earlier ‐C‐O‐Si‐ analogues. These MMs were also used to create a linear‐bottlebrush‐linear block copolymer, forming a supersoft (E = 79 kPa), thermoplastic elastomer with excellent elastic recovery (~96%). This platform enables the synthesis of ultra‐high molecular weight graft (co‐)polymers, advancing the study of extreme structure–property relationships and supporting the development of novel soft materials for bio‐interfacing.
more »
« less
- Award ID(s):
- 2045336
- PAR ID:
- 10676843
- Publisher / Repository:
- Wiley
- Date Published:
- Journal Name:
- Journal of Polymer Science
- Volume:
- 63
- Issue:
- 18
- ISSN:
- 2642-4150
- Page Range / eLocation ID:
- 3723 to 3730
- Subject(s) / Keyword(s):
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
<sc>A</sc>bstract We introduce a simple synthetic strategy to selectively degrade bottlebrush networks derived from well‐defined poly(4‐methylcaprolactone) (P4MCL) bottlebrush polymers. Functionalization of the hydroxyl groups present at the terminal ends of P4MCL side chains withα‐lipoic acid resulted in bottlebrush polymers having a range of molecular weights (Mn = 45–2200 kg mol−1) and a tunable number of reactive dithiolane chain ends. These functionalized chain ends act as efficient crosslinkers due to radical ring‐opening of the dithiolane rings under UV light. The resulting redox‐active disulfide crosslinks enable mild electrochemical or chemical degradation of the SS crosslinks to regenerate the starting bottlebrush polymer. P4MCL side chains and the disulfides can be degraded simultaneously using harsher reducing conditions. This combination of bottlebrush architecture with facile disulfide crosslinking presents a versatile platform for preparing highly tunable elastomers that undergo controlled degradation under mild conditions.more » « less
-
Macromolecular architecture is a critical parameter when tuning polymer material properties. Although the implementation of non-linear polymers in different applications has grown over the years, polymer grafted surfaces such as nanoparticles have traditionally been composed of linear thermoplastic polymers, with a limited number of examples demonstrating a diversity in polymer architectures. In an effort to combine polymer architecturally dependent material properties with polymer grafted particles (PGPs), as opposed to conventional methods of tuning polymer grafting parameters such as the number of chains per surface area (i.e., polymer graft density), a series of bottlebrush grafted particles were synthesized using surface-initiated ring-opening metathesis polymerization (SI-ROMP). These bottlebrush PGPs are composed of glassy, semi-crystalline, and elastomeric polymer side chains with controlled backbone degrees of polymerization (Nbb) at relatively constant polymer graft density on the surface of silica particles with diameters equaling approximately 160 or 77 nm. Bottlebrush polymer chain conformations, evaluated by measuring the brush height of surface grafted polymer chains in solution and the melt, undergo drastic changes in macromolecular dimensions in different environments. In solution, brush heights increase linearly as a function of Nbb, consistent with fully stretched chains, which is confirmed using cryogenic transmission electron microscopy (Cryo-TEM). Meanwhile, brush heights are consistently at a minimum in the melt, indicative of chains collapsed on the particle surface. The conformational extremes for grafted bottlebrush polymers are unseen in any linear polymer chain systems, highlighting the effect of macromolecular architecture and surface grafting. Bottlebrush grafted particles are an exciting class of materials where diversifying polymer architectures will expand PGP material design rules that harness macromolecular architecture to dictate properties.more » « less
-
Abstract This present study illustrates the synthesis and preparation of polyoxanorbornene‐based bottlebrush polymers with poly(ethylene oxide) (PEO) side chains by ring‐opening metathesis polymerization for solid polymer electrolytes (SPE). In addition to the conductive PEO side chains, the polyoxanorbornene backbones may act as another ion conductor to further promote Li‐ion movement within the SPE matrix. These results suggest that these bottlebrush polymer electrolytes provide impressively high ionic conductivity of 7.12 × 10−4S cm−1at room temperature and excellent electrochemical performance, including high‐rate capabilities and cycling stability when paired with a Li metal anode and a LiFePO4cathode. The new design paradigm, which has dual ionic conductive pathways, provides an unexplored avenue for inventing new SPEs and emphasizes the importance of molecular engineering to develop highly stable and conductive polymer electrolytes for lithium‐metal batteries (LMB).more » « less
-
Abstract A versatile synthetic platform is reported that affords high molecular weight graft copolymers containing polydimethylsiloxane (PDMS) backbones and vinyl‐based polymer side chains with excellent control over molecular weight and grafting density. The synthetic approach leverages thiol‐ene click chemistry to attach an atom‐transfer radical polymerization (ATRP) initiator to a variety of commercially available poly(dimethylsiloxane‐co‐methylvinylsiloxane) backbones (PDMS‐co‐PVMS), followed by controlled radical polymerization with a wide scope of vinyl monomers. Selective degradation of the siloxane backbone with tetrabutylammonium fluoride confirmed the controlled nature of side‐chain growth via ATRP, yielding targeted side‐chain lengths for copolymers containing up to 50% grafting density and overall molecular weights in excess of 1 MDa. In addition, by using a mixture of thiols, grafting density and functionality can be further controlled by tuning initiator loading along the backbone. For example, solid‐state fluorescence of the graft copolymers was achieved by incorporating a thiol‐containing fluorophore along the siloxane backbone during the thiol‐ene click reaction. This simple synthetic platform provides facile control over the properties of a wide variety of grafted copolymers containing flexible PDMS backbones and vinyl polymer side chains.more » « less
An official website of the United States government

