This content will become publicly available on March 12, 2027

Title: Effects of Compaction Rotation Speed and Compaction Thickness in Roller-Compaction-Assisted Binder Jetting Additive Manufacturing
Powder bed compaction can be used to control powder bed density in binder jetting additive manufacturing. Applying a forward-rotating roller to the powder bed is one of the methods for powder bed compaction. Both the compaction rotation speed and compaction thickness are critical parameters affecting the powder packing density and resultant printed sample integrity. However, their joint effects have not been investigated for roller-compaction-assisted binder jetting. This paper reports an experimental study to investigate the effects of the compaction rotation speed and the compaction thickness on powder bed density and the printed sample quality (in terms of distortion and cracks). The experimental results showed that powder bed density was not affected by changing compaction rotation speed but was enhanced by increasing compaction thickness. Small compaction thickness did not cause any observable distortions or cracks in the printed samples at any compaction rotation speed. Large compaction thickness caused printed samples to distort and crack under specific conditions. At large compaction thickness, compaction rotation speed significantly affected both the direction and extent of the printed sample distortion. Samples with improved density and integrity were achieved in the center of the build platform at large compaction thickness and at a compaction circumferential speed larger than the compaction traverse speed. These results can help optimize binder jetting additive manufacturing for printed sample quality.  more » « less
Award ID(s):
2401277
PAR ID:
10686984
Author(s) / Creator(s):
; ; ; ;
Publisher / Repository:
MDPI
Date Published:
Journal Name:
Journal of Manufacturing and Materials Processing
Volume:
10
Issue:
3
ISSN:
2504-4494
Page Range / eLocation ID:
97
Subject(s) / Keyword(s):
Sponsoring Org:
National Science Foundation
More Like this
  1. Binder jetting is a powder bed additive manufacturing process where an object is created by depositing liquid binder onto the surface of powder, selectively binding particles in each layer. The quality of the as-printed parts is influenced not only by process parameters such as layer thickness, binder saturation, print speed, and drying time but also by the location within the build box. This study highlights the location-dependent nature of green density and dimensional accuracy in the as-printed samples, and the observed trends are thoroughly discussed. A conventional powder spreading using a single roller was compared with a double roller to maximize powder packing and bed uniformity prior to binder jetting process. The significance of these observations lies in their impact on densification behavior, shrinkage, and the final geometry of the printed part. 
    more » « less
  2. Binder jetting of minimally processed, locally sourced sediments offers a promising route toward sustainable additive manufacturing, but powder spreading of poorly sorted, irregular grains remains underexplored. This study uses high-fidelity Discrete Element Method (DEM) simulations to quantify how process parameters govern layer quality when spreading an unrefined sandy silt from the Gypsum Hills, Kansas, USA, with a counter-rotating roller. Twenty-five multi-sphere particle shapes were reconstructed from morphological measurements and used to simulate up to 300,000 interacting grains while systematically varying roller traverse speed, rotational speed, diameter, and layer thickness. Traverse speed and layer thickness emerged as the dominant controls on powder bed density and uniformity: the slowest traverse speed (20 mm/s) produced the highest density (~ 0.50) and lowest variability (~ 0.08), and layer thicknesses ≥ 120 μm were required to avoid jamming and obtain consistent packing. In contrast, roller diameter and rotational speed had only minor influence over the explored ranges. The simulations also revealed percolation-driven segregation, with fine particles preferentially settling beneath coarser grains. Comparison with an idealized spherical powder showed that the silt is intrinsically harder to spread, achieving lower density (0.51 vs. 0.59) and higher variability. These results demonstrate that binder jet processing of unrefined silt is feasible but favors slower spreading and thicker layers that may reduce throughput and resolution, and they provide process design guidelines and particle-scale insight for deploying raw earth feedstocks in sustainable binder jetting. 
    more » « less
  3. Abstract This technical brief reports an experimental investigation on the effect of feed region density on resultant sintered density and intermediate densities (powder bed density and green density) during the binder jetting additive manufacturing process. The feed region density was increased through compaction. The powder bed density and green density were determined by measuring the mass and dimension. The sintered density was measured with the Archimedes’ method. As the relative feed region density increased from 44% to 65%, the powder bed density increased by 5.7%, green density by 8.5%, and finally sintered density by 4.5%. Statistical testing showed that these effects were significant. This study showed that compacting the powder in the feed region is an effective method to alter the density of parts made via binder jetting additive manufacturing. 
    more » « less
  4. In binder jet additive manufacturing (BJAM), uniformity and density of the powder layer impact green part quality. This study investigates the printability of unrefined sand using counter-roller spreading. Altair EDEM, a high-performance software powered by the Discrete Element Method (DEM), was used to simulate the BJAM process to evaluate powder bed homogeneity and density under various operating conditions, including roller rotational speed, traverse speed, powder layer thickness, and roller diameter. Utilizing high-performance computing (HPC) and graphics processing unit (GPU) clusters, time-efficient, and more realistic, simulations were performed simulating 300,000 grains. Detailed DEM simulations were executed by reconstructing representative particle shapes using two-dimensional images obtained using particle characterization equipment. The results highlight roller velocity and powder layer thickness as key determinants of sand spreadability. Optimal powder bed density (PBD) was achieved at a roller velocity of 20 mm/s with minimal deviation. A layer thickness exceeding 200 micrometers was found to prevent jamming and void formation, while percolation led to size segregation. The findings indicate that producing uniform and dense layers of unrefined sand is feasible but may incur trade-offs in print resolution and increased printing times. This work contributes to the advancement of sustainable and/or remote BJAM technologies, ensuring progress in both environmental sustainability and accessibility. 
    more » « less
  5. Abstract Binder jetting is an additive manufacturing process utilizing a liquid-based binding agent to selectively join the material in a powder bed. It is capable of manufacturing complex-shaped parts from a variety of materials including metals, ceramics, and polymers. This paper provides a comprehensive review on currently available reports on metal binder jetting from both academia and industry. Critical factors and their effects in metal binder jetting are reviewed and divided into two categories, namely material-related factors and process-related parameters. The reported data on density, dimensional and geometric accuracy, and mechanical properties achieved by metal binder jetting are summarized. With parameter optimization and a suitable sintering process, ten materials have been proven to achieve a relative density of higher than 90%. Indepth discussion is provided regarding densification as a function of various attributes of powder packing, printing, and post-processing. A few grades of stainless steel obtained equivalent or superior mechanical properties compared to cold working. Although binder jetting has gained its popularity in the past several years, it has not been sufficiently studied compared with other metal additive manufacturing (AM) processes such as powder bed fusion and directed energy deposition. Some aspects that need further research include the understanding of powder spreading process, binder-powder interaction, and part shrinkage. 
    more » « less