An official website of the United States government
We study the fragmentation of pre-perforated thin liquid films using three-dimensional numerical simulations, focusing on droplet formation following hole collisions. An air–water system with film thickness e0=25 μm and varying hole spacings (dh/e0=3−20) is considered. The liquid bridge formed between colliding holes undergoes oscillation and stretching before breakup. The outcome depends on the spacing: for small dh, ligaments recoil into single droplets, while for larger dh, ligaments fragment via end-pinching and Rayleigh–Plateau (RP) instabilities. Droplet size distributions are compared with RP predictions and show improved agreement when a 40% reduction in ligament diameter due to stretching is accounted for. The results also compare favorably with experimental data from air-blasted films. This work provides new insight into the fundamental mechanisms controlling droplet formation from perforated films and highlights the critical role of hole spacing in determining ligament dynamics and droplet size distributions.
more »
« less
From vortices to droplets: Gas-phase instability effects on thin liquid film breakup
This study explores the role of gas flow dynamics in the fragmentation of thin liquid sheets using three-dimensional numerical simulations. A thin liquid sheet with a thickness of 25 μm is subjected to high-velocity co-flowing gas streams characterized by three distinct gas Reynolds numbers, namely, Reg=300,500, and 1000. Simulations show that the breakup behavior of the sheet is governed by the vortical structures formed in the gas flow, which range from oblique vortex shedding at lower Reg to rib-like vortical patterns at higher Reg. The gas-induced instabilities impose transverse and longitudinal oscillations on the liquid sheet, which govern the locations of hole formation, the development of ligaments, and ultimately the resulting droplet size distribution. For Reg=300, breakup occurs via rim instability and the end-pinching or Rayleigh–Plateau-type instability of liquid fingers, whereas for Reg=500 and 1000, sheet rupture through hole formation and collision dominates. A manifold death (MD) algorithm is used to enforce breakup at a grid-independent critical film thickness, improving robustness against numerical artifacts. Droplet size distributions obtained with and without the MD algorithm confirm that the dominant droplet size remains unchanged, while the formation of small, potentially spurious droplets is suppressed. The resulting distributions align more closely with a lognormal model, consistent with the presence of multiple breakup mechanisms. This work provides new insight into the coupling between gas-phase instabilities and liquid fragmentation, offering a pathway to more accurate predictive models for air-blast atomization processes.
more »
« less
- Award ID(s):
- 2524705
- PAR ID:
- 10693776
- Publisher / Repository:
- AIP Publishing: Physics of Fluids
- Date Published:
- Journal Name:
- Physics of Fluids
- Volume:
- 37
- Issue:
- 8
- ISSN:
- 1070-6631
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
null (Ed.)Liquid-in-air generation of monodisperse, microscale droplets is an alternative to conventional liquid-in-liquid methods. Previous work has validated the use of a highly inertial gaseous continuous phase in the production of monodisperse droplets in the dripping regime using planar, flow-focusing, PDMS microchannels. The jetting flow regime, characteristic of small droplet size and high generation rates, is studied here in novel microfluidic geometries. The region associated with the jetting regime is characterized using the liquid Weber number (Wel) and the gas Reynolds number (Reg). We explore the effects of microchannel confinement on the development and subsequent breakup of the liquid jet as well as the physical interactions between the jet and continuous gaseous flow. Droplet breakup in the jetting regime is also studied numerically and the influence of different geometrical parameters is investigated. Numerical simulations of the jetting regime include axisymmetric cases where the jet diameter and length are studied. This work represents a vital investigation into the physics of droplet breakup in the jetting regime subject to a confined gaseous co-flow. By understanding the effects that different flow and geometry conditions have on the generation of droplets, the use of this system can be optimized for specific high-demand applications in the aerospace, material, and biological industries.more » « less
-
Understanding the development and breakup of interfacial waves in a two-phase mixing layer between the gas and liquid streams is paramount to atomization. Due to the velocity difference between the two streams, the shear on the interface triggers a longitudinal instability, which develops to interfacial waves that propagate downstream. As the interfacial waves grow spatially, transverse modulations arise, turning the interfacial waves from quasi-two-dimensional to fully three-dimensional. The inlet gas turbulence intensity has a strong impact on the interfacial instability. Therefore, parametric direct numerical simulations are performed in the present study to systematically investigate the effect of the inlet gas turbulence on the formation, development and breakup of the interfacial waves. The open-source multiphase flow solver, PARIS, is used for the simulations and the mass–momentum consistent volume-of-fluid method is used to capture the sharp gas–liquid interfaces. Two computational domain widths are considered and the wide domain will allow a detailed study of the transverse development of the interfacial waves. The dominant frequency and spatial growth rate of the longitudinal instability are found to increase with the inlet gas turbulence intensity. The dominant transverse wavenumber, determined by the Rayleigh–Taylor instability, scales with the longitudinal frequency, so it also increases with the inlet gas turbulence intensity. The holes formed in the liquid sheet are important to the disintegration of the interfacial waves. The hole formation is influenced by the inlet gas turbulence. As a result, the sheet breakup dynamics and the statistics of the droplets formed also change accordingly.more » « less
-
This study investigates the atomization process in Respimat® Soft MistTM Inhalers (SMIs) using a validated Volume of Fluid (VOF)-to-Discrete Phase Model (DPM) to simulate the transition from colliding liquid jets to aerosolized droplets. Key parameters, including colliding jet inlet velocity, surface tension, and liquid viscosity, were systematically varied to analyze their impact on the atomization, i.e., aerosolized droplet size distributions. The VOF-to-DPM simulation results indicate that higher jet inlet velocities enhance ligament fragmentation, producing finer and more uniform droplets while reducing total atomized droplet mass. The relationship between surface tension and atomization performance in colliding jet atomization is not monotonic. Reducing surface tension plays a complex dual role in the atomization process. On the one hand, lower surface tension enhances the likelihood of liquid jet breakup into a liquid sheet, leading to the formation of smaller ligaments under the same airflow conditions and shear forces. This increases the probability of generating more secondary droplets. On the other hand, reduced surface tension also destabilizes the liquid surface shape, decreasing the formation of fine, high-sphericity droplets in regimes where surface tension is a dominant force. Viscosity also influences atomization through complex mechanisms, i.e., lower viscosity reduces resistance to ligament breakup but promotes droplet interactions and coalescence, while higher viscosity suppresses ligament fragmentation, generating larger droplets and reducing atomization efficiency. The validated VOF-to-DPM framework provides critical insights for enhancing the performance and efficiency of inhalation therapies. Future work will incorporate nozzle geometry, jet impingement angles, and surfactant effects to better understand and optimize the atomization process in SMIs, focusing on achieving preferred droplet size distributions and emitted doses for enhanced drug delivery efficiency in human respiratory systems.more » « less
-
Hybrid rocket motors with paraffin-based fuels are of interest due to higher regression rates compared to other polymers. During paraffin combustion, a liquid layer forms on the fuel surface that, together with shearing forces from the oxidizer flow, results in the formation of instabilities at the fuel-oxidizer interface. These instabilities lead to the formation and entrainment of heterogeneous sized liquid droplets into the main flow and the combusting droplets result in higher motor output. The atomization process begins with droplet formation and ends with droplet pinch-off. The goal of this paper is to conduct an uncertainty quantification (UQ) analysis of the pinch-off process characterized by a pinch-off volume ($$V_{po}$$) and time ($$t_{po}$$). We study these quantities of interest (QoIs) in the context of a slab burner setup. We have developed a computationally expensive mathematical model that describes droplet formation under external forcing and trained an inexpensive Gaussian Process surrogate of the model to facilitate UQ. We use the pinch-off surrogate to forward propagate uncertainty of the model inputs to the QoIs and conduct two studies: one with gravity present and one without gravity effects. After forward-propagating the uncertainty of the inputs using the surrogate, we concluded that both QoIs have right-skewed distributions, corresponding to larger probability densities towards smaller pinch-off volumes and times. Specifically, for the pinch-off times, the resulting distributions reflect the effect of gravity acting against droplet formation, resulting in longer pinch-off times compared to the case where there is no gravity.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript
- Journal Article:
- https://doi.org/10.1063/5.0278367
