An official website of the United States government
This study explores the role of gas flow dynamics in the fragmentation of thin liquid sheets using three-dimensional numerical simulations. A thin liquid sheet with a thickness of 25 μm is subjected to high-velocity co-flowing gas streams characterized by three distinct gas Reynolds numbers, namely, Reg=300,500, and 1000. Simulations show that the breakup behavior of the sheet is governed by the vortical structures formed in the gas flow, which range from oblique vortex shedding at lower Reg to rib-like vortical patterns at higher Reg. The gas-induced instabilities impose transverse and longitudinal oscillations on the liquid sheet, which govern the locations of hole formation, the development of ligaments, and ultimately the resulting droplet size distribution. For Reg=300, breakup occurs via rim instability and the end-pinching or Rayleigh–Plateau-type instability of liquid fingers, whereas for Reg=500 and 1000, sheet rupture through hole formation and collision dominates. A manifold death (MD) algorithm is used to enforce breakup at a grid-independent critical film thickness, improving robustness against numerical artifacts. Droplet size distributions obtained with and without the MD algorithm confirm that the dominant droplet size remains unchanged, while the formation of small, potentially spurious droplets is suppressed. The resulting distributions align more closely with a lognormal model, consistent with the presence of multiple breakup mechanisms. This work provides new insight into the coupling between gas-phase instabilities and liquid fragmentation, offering a pathway to more accurate predictive models for air-blast atomization processes.
more »
« less
This content will become publicly available on June 1, 2027
Droplet size distribution in the fragmentation of liquid films via hole collisions
We study the fragmentation of pre-perforated thin liquid films using three-dimensional numerical simulations, focusing on droplet formation following hole collisions. An air–water system with film thickness e0=25 μm and varying hole spacings (dh/e0=3−20) is considered. The liquid bridge formed between colliding holes undergoes oscillation and stretching before breakup. The outcome depends on the spacing: for small dh, ligaments recoil into single droplets, while for larger dh, ligaments fragment via end-pinching and Rayleigh–Plateau (RP) instabilities. Droplet size distributions are compared with RP predictions and show improved agreement when a 40% reduction in ligament diameter due to stretching is accounted for. The results also compare favorably with experimental data from air-blasted films. This work provides new insight into the fundamental mechanisms controlling droplet formation from perforated films and highlights the critical role of hole spacing in determining ligament dynamics and droplet size distributions.
more »
« less
- Award ID(s):
- 2524705
- PAR ID:
- 10693777
- Publisher / Repository:
- AIP Publishing
- Date Published:
- Journal Name:
- Physics of Fluids
- Volume:
- 38
- Issue:
- 6
- ISSN:
- 1070-6631
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
This study investigates the atomization process in Respimat® Soft MistTM Inhalers (SMIs) using a validated Volume of Fluid (VOF)-to-Discrete Phase Model (DPM) to simulate the transition from colliding liquid jets to aerosolized droplets. Key parameters, including colliding jet inlet velocity, surface tension, and liquid viscosity, were systematically varied to analyze their impact on the atomization, i.e., aerosolized droplet size distributions. The VOF-to-DPM simulation results indicate that higher jet inlet velocities enhance ligament fragmentation, producing finer and more uniform droplets while reducing total atomized droplet mass. The relationship between surface tension and atomization performance in colliding jet atomization is not monotonic. Reducing surface tension plays a complex dual role in the atomization process. On the one hand, lower surface tension enhances the likelihood of liquid jet breakup into a liquid sheet, leading to the formation of smaller ligaments under the same airflow conditions and shear forces. This increases the probability of generating more secondary droplets. On the other hand, reduced surface tension also destabilizes the liquid surface shape, decreasing the formation of fine, high-sphericity droplets in regimes where surface tension is a dominant force. Viscosity also influences atomization through complex mechanisms, i.e., lower viscosity reduces resistance to ligament breakup but promotes droplet interactions and coalescence, while higher viscosity suppresses ligament fragmentation, generating larger droplets and reducing atomization efficiency. The validated VOF-to-DPM framework provides critical insights for enhancing the performance and efficiency of inhalation therapies. Future work will incorporate nozzle geometry, jet impingement angles, and surfactant effects to better understand and optimize the atomization process in SMIs, focusing on achieving preferred droplet size distributions and emitted doses for enhanced drug delivery efficiency in human respiratory systems.more » « less
-
null (Ed.)When a droplet is generated, the ligament connecting the drop to the nozzle thins down and eventually pinches off. Adding solid particles to the liquid phase leads to a more complex dynamic, notably by increasing the shear viscosity. Moreover, it introduces an additional length scale to the system, the diameter of the particles, which eventually becomes comparable to the diameter of the ligament. In this paper, we experimentally investigate the thinning and pinch-off of drops of suspensions with two different sizes of particles. We characterize the thinning for different particle size ratios and different proportions of small particles. Long before the pinch-off, the thinning rate is that of an equivalent liquid whose viscosity is that of the suspension. Later, when the ligament thickness approaches the size of the large particles, the thinning accelerates and leads to an early pinch-off. We explain how the bidisperse particle size distribution lowers the viscosity by making the packing more efficient, which speeds up the thinning. This result can be used to predict the dynamics of droplet formation with bidisperse suspensions.more » « less
-
Introduction:Agriculture is the largest user of water globally (i.e., 70% of freshwater use) and within the United States (i.e., 42% of freshwater use); irrigation ensures crops receive adequate water, thereby increasing crop yields. Surfactants have been used in various agricultural spray products to increase spray stability and alter droplet sizes. Methods:The effects of the addition of surfactant (0.1 wt% Surfactin; surface tension of 29.2 mN/m) to distilled water (72.79 mN/m) on spray dynamics and droplet formation were investigated in four flat fan (206.8–413.7 kPa), one full cone (137.9–413.7 kPa), and three LEPA bubbler (41.4–103.4 kPa) nozzles via imaging. Results and discussion:The flat fan and cone nozzles experienced second wind-induced breakup (i.e., unstable wavelengths drive breakup) of the liquid sheets exiting the nozzle; the addition of surfactant resulted in an increased breakup length and a decreased droplet size. The fan nozzles volumetric median droplet diameter decreased with the addition of surfactant (e.g., decreased by 26.3–65.6 μm in one nozzle). The full cone nozzle volumetric median droplet diameter decreased initially with the addition of surfactant (27.8, 14.3, and 13.4 μm at 137.9, 206.8, and 310.3 kPa respectively), but increased at 413.7 kPa (24.3 μm). Sprays from the bubbler nozzles were measured and observed to experience Rayleigh (i.e., the droplets form via capillary pinching at the end of the jet) and first wind-induced breakup (i.e., air impacts breakup along with capillary pinching). The effect of Surfactin on droplet size was minimal for the 41.4 kPa bubbler nozzle. The addition of surfactant increased the diameter of the jet or ligament formed from the bubbler plate, thereby increasing the breakup length and the droplet size at 68.9 and 103.4 kPa (droplet size increased by 750.6 and 4,462.7 μm, respectively).more » « less
-
null (Ed.)Binder Jetting (BJ) is a low-cost Additive Manufacturing (AM) process that uses inkjet technology to selectively bind particles in a powder bed. BJ relies on the ability to control, not only the placement of binder on the surface but also its imbibition into the powder bed. This is a complex process in which picoliter-sized droplets impact powder beds at velocities of 1–10 m/s. However, the effects of printing parameters such as droplet velocity, size, spacing, and inter-arrival time on saturation level (fraction of pore space filled with binder) and line formation (merging of droplets to form a line) are unknown. Prior attempts to predict saturation levels with simple measurements of droplet primitives and capillary pressure assume that droplet/powder interactions are dominated by static equilibrium and neglect the impact of printing parameters. This study analyzes the influence of these parameters on the effective saturation level and conditions for line formation when printing single lines into powder beds of varied materials (316 stainless steel, 420 stainless steel, and alumina) and varied particle size (d50=10–47 µm). Results show that increasing droplet velocity or droplet spacing decreases effective saturation while droplet spacing, velocity, and inter-arrival time affect line formation. At constant printing velocity, the conditions for successful line printing are shown to be a function of droplet spacing and square root of the droplet inter-arrival time analogous to the Washburn model for infiltration into a porous media. The results have implications to maximizing build rates and improving quality of small features in BJ.more » « less
