Search for: All records

Sr(Ti 0.3 Fe 0.7 )O 3−δ (STF) and the associated exsolution electrodes Sr 0.95 (Ti 0.3 Fe 0.63 Ru 0.07 )O 3−δ (STFR), or Sr 0.95 (Ti 0.3 Fe 0.63 Ni 0.07 )O 3−δ (STFN) are alternatives to Ni-based cermet fuel electrodes for solid oxide electrochemical cells (SOCs). They can provide improved tolerance to redox cycling and fuel impurities, and may allow direct operation with hydrocarbon fuels. However, such perovskite-oxide-based electrodes present processing challenges for co-sintering with thin electrolytes to make fuel electrode supported SOCs. Thus, they have been mostly limited to electrolyte-supported SOCs. Here, we report the first example of the application of perovskite oxide fuel electrodes in novel oxygen electrode supported SOCs (OESCs) with thin YSZ electrolytes, and demonstrate their excellent performance. The OESCs have La 0.8 Sr 0.2 MnO 3−δ –Zr 0.92 Y 0.16 O 2−δ (LSM–YSZ) oxygen electrode-supports that are enhanced via infiltration of SrTi 0.3 Fe 0.6 Co 0.1 O 3−δ , while the fuel electrodes are either Ni-YSZ, STF, STFN, or STFR. Fuel cell power density as high as 1.12 W cm −2 is obtained at 0.7 V and 800 °C in humidified hydrogen and air with the STFR electrode, 60% higher than the same cell made with a Ni-YSZ electrode. Electrolysis current density as high as −1.72 A cm −2 is obtained at 1.3 V and 800 °C in 50% H 2 O to 50% H 2 mode; the STFR cell yields a value 72% higher than the same cell made with a Ni-YSZ electrode, and competitive with the widely used conventional Ni-YSZ-supported cells. The high performance is due in part to the low resistance of the thin YSZ electrolyte, and also to the low fuel electrode polarization resistance, which decreases with fuel electrode in the order: Ni-YSZ > STF > STFN > STFR. The high performance of the latter two electrodes is due to exsolution of catalytic metal nanoparticles; the results are discussed in terms of the microstructure and properties of each electrode material, and surface oxygen exchange resistance values are obtained over a range of conditions for STF, STFN, and STFN. The STF fuel electrodes also provide good stability during redox cycling. 

Sr(Ti 1−x Fe x )O 3−δ (STF) has recently been explored as an oxygen electrode for solid oxide electrochemical cells (SOCs). Model thin film electrode studies show oxygen surface exchange rates that generally improve with increasing Fe content when x < 0.5, and are comparable to the best Co-containing perovskite electrode materials. Recent results on porous electrodes with the specific composition Sr(Ti 0.3 Fe 0.7 )O 3−δ show excellent electrode performance and stability, but other compositions have not been tested. Here we report results for porous electrodes with a range of compositions from x = 0.5 to 0.9. The polarization resistance decreases with increasing Fe content up to x = 0.7, but increases for further increases in x . This results from the interaction of two effects – the oxygen solid state diffusion coefficient increases with increasing x , but the electrode surface area and surface oxygen exchange rate decrease due to increased sinterability and Sr surface segregation for the Fe-rich compositions. Symmetric cells showed no degradation during 1000 h life tests at 700 °C even at a current density of 1.5 A cm −2 , showing that all the STF electrode compositions worked stably in both fuel cell mode and electrolysis modes. The excellent stability may be explained by X-ray Photoelectron Spectroscopy (XPS) results showing that the amount of surface segregated Sr did not change during the long-term testing, and by relatively low polarization resistances that help avoid electrode delamination. 

A novel and efficient method is demonstrated to improve the electrochemical performance of Li 4 Ti 5 O 12 and metal-oxide anodes. In contrast to other methods, inexpensive red phosphorus powder is used as a reducing reagent, and the reduction is conducted at a relatively low temperature of 400 °C. This method offers a low cost and effective way for Li 4 Ti 5 O 12 and metal-oxide anode applications. 

Abstract. During the COVID-19 lockdown, the dramatic reduction of anthropogenicemissions provided a unique opportunity to investigate the effects ofreduced anthropogenic activity and primary emissions on atmospheric chemicalprocesses and the consequent formation of secondary pollutants. Here, weutilize comprehensive observations to examine the response of atmosphericnew particle formation (NPF) to the changes in the atmospheric chemicalcocktail. We find that the main clustering process was unaffected by thedrastically reduced traffic emissions, and the formation rate of 1.5 nmparticles remained unaltered. However, particle survival probability wasenhanced due to an increased particle growth rate (GR) during the lockdownperiod, explaining the enhanced NPF activity in earlier studies. For GR at1.5–3 nm, sulfuric acid (SA) was the main contributor at high temperatures,whilst there were unaccounted contributing vapors at low temperatures. ForGR at 3–7 and 7–15 nm, oxygenated organic molecules (OOMs) played amajor role. Surprisingly, OOM composition and volatility were insensitive tothe large change of atmospheric NOx concentration; instead theassociated high particle growth rates and high OOM concentration during thelockdown period were mostly caused by the enhanced atmospheric oxidativecapacity. Overall, our findings suggest a limited role of traffic emissionsin NPF.