Search for: All records

Seagrasses play an important role in coastal ecosystems and serve as important marine carbon stores. Acoustic monitoring techniques exploit the sensitivity of underwater sound to bubbles, which are produced as a byproduct of photosynthesis and present within the seagrass tissue. To make accurate assessments of seagrass biomass and productivity, a model is needed to describe acoustic propagation through the seagrass meadow that includes the effects of gas contained within the seagrass leaves. For this purpose, a new seagrass leaf model is described for Thalassia testudinum that consists of a comparatively rigid epidermis that composes the outer shell of the leaf and comparatively compliant aerenchyma that surrounds the gas channels on the interior of the leaf. With the bulk modulus and density of the seagrass tissue determined by previous work, this study focused on characterizing the shear moduli of the epidermis and aerenchyma. These properties were determined through a combination of dynamic mechanical analysis and acoustic resonator measurements coupled with microscopic imagery and finite element modeling. The shear moduli varied as a function of length along the leaves with values of 100 and 1.8 MPa at the basal end and 900 and 3.7 MPa at the apical end for the epidermis and aerenchyma, respectively.

 

Acoustic propagation measurements were collected in a seagrass meadow in a shallow lagoon for periods of over 65 h in winter and 93 h in summer. A bottom-deployed sound source transmitted chirps (0.1–100 kHz) every 10 min that were received on a four-receiver horizontal hydrophone array. Oceanographic probes measured various environmental parameters. Daytime broadband acoustic attenuation was 2.4 dB greater in summer than winter, and the median received acoustic energy levels were 8.4 dB lower in summer compared to winter. These differences were attributed in part to seasonal changes in photosynthesis bubble production and above-ground seagrass biomass.

 

A spark plug calorimeter is introduced for quantifying the thermal energy delivered to unreactive gas surrounding the spark gap during spark ignition. Unlike other calorimeters, which measure the small pressure rise of the gas above the relatively high gauge pressure or relative to an internal reference, the present calorimeter measured the differential rise in pressure relative to the initial pressure in the calorimeter chamber. By using a large portion of the dynamic range of the chip-based pressure sensor, a high signal to noise ratio is possible; this can be advantageous, particularly for high initial pressures. Using this calorimeter, a parametric study was carried out, measuring the thermal energy deposition in the gas and the electrical-to-thermal energy conversion efficiency over a larger range of initial pressures than has been carried out previously (1–24 bar absolute at 298 K). The spark plug and inductive ignition circuit used gave arc-type rather than glow-type discharges. A standard resistor-type automotive spark plug was tested. The effects of spark gap distance (0.3–1.5 mm) and ignition dwell time (2–6 ms) were studied for an inductive-type ignition system. It was found that energy deposition to the gas (nitrogen) and the electrical-to-thermal energy conversion efficiency increased strongly with increasing gas pressure and spark gap distance. For the same ignition hardware and operating conditions, the thermal energy delivered to the gap varied from less than 1 mJ at 1 atm pressure and a gap distance of 0.3 mm to over 25 mJ at a pressure of 24 bar and a gap distance of 1.5 mm. For gas densities that might be representative of those in an engine at the time of ignition, the electrical-to-thermal energy conversion efficiencies ranged from approximately 3% at low pressures (4 bar) and small gap (0.3 mm) to as much as 40% at the highest pressure of 24 bar and with a gap of 1.5 mm. 

Metamaterials have offered unprecedented potentials for wave manipulations. However, their applications in underwater acoustic wave control have remained largely unexplored. This is because of the limited material choices and the lack of reliable fabrication techniques for the complicated structures. Herein, a metamaterial with microlattice structures as the building blocks is proposed for underwater operations. By designing the building blocks of the metamaterial and assembling them in a layered fashion, anisotropy is embedded in the structure, which results along different effective sound speeds in orthogonal directions. The designed metamaterial is fabricated by metal additive manufacturing using aluminum and steel. Experiments are performed using a resonator tube to evaluate its performance in water. An anisotropy ratio of around 2 is achieved, which is in good agreement with numerical simulations. The proposed metamaterial provides an effective means for underwater sound control with reduced fabrication difficulties and increased service life.