Search for: All records

Mechanochemical reaction pathways are conventionally obtained from force-displaced stationary points on the potential energy surface of the reaction. This work tests a postulate that the steepest-descent pathway (SDP) from the transition state to reactants can be reasonably accurately used instead to investigate mechanochemical reaction kinetics. This method is much simpler because the SDP and the associated reactant and transition-state structures can be obtained relatively routinely. Experiment and theory are compared for the normal-stress-induced decomposition of methyl thiolate species on Cu(100). The mechanochemical reaction rate was calculated by compressing the initial- and transition-state structures by a stiff copper counter-slab to obtain the plots of energy versus slab displacement for both structures. The reaction rate was also measured experimentally under compression using a nanomechanochemical reactor comprising an atomic-force-microscopy (AFM) instrument tip compressing a methyl thiolate overlayer on Cu(100) (the same system for which the calculations were carried out). The rate was measured from the indent created on a defect-free region of the methyl thiolate overlayer, which also enabled the contact area to be measured. Knowing the force applied by the AFM tip yields the reaction rate as a function of the contact stress. The result agrees well with the theoretical prediction without the use of adjustable parameters. This confirms that the postulate is correct and will facilitate the calculation of the rates of more complex mechanochemical reactions. An advantage of this approach, in addition to the results agreeing with the experiment, is that it provides insights into the effects that control mechanochemical reactivity that will assist in the targeted design of new mechanochemical syntheses. 

The rates of mechanochemical reactions are generally found to increase exponentially with applied stress. However, a buckling theory analysis of the effect of a normal stress on an adsorbate that is oriented perpendicularly to the surface that reacts by tilting suggests that a critical value of the stress should be required to initiate a mechanochemical reaction. This concept is verified by using density functional theory calculations to simulate the effect of compressing a homologous series of alkyl thiolate species on copper by a hydrogen-terminated copper counter-face. This predicts that a critical stress is indeed needed to initiate methyl thiolate decomposition, which has a perpendicular C–CH 3 bond. In contrast, no critical stress is found for ethyl thiolate with an almost horizontal C–CH 3 bond, while a critical stress is required to isomerize propyl thiolate from a trans to a cis configuration. These predictions are tested by measuring the mechanochemical reaction rates of these alkyl thiolates on a Cu(100) substrate by sliding an atomic force microscope tip over the surface and finding a critical stress of ∼0.43 GPa for methyl thiolate, ∼0.33 GPa for propyl thiolate, but no evidence of a critical stress for ethyl thiolate, in accord with the predictions. These results provide insights not only into mechanochemical reaction mechanisms on surfaces, but also on the origin of critical phenomena in stress-induced processes in general. It also suggests novel approaches to designing robust surface films that can resist wear and damage. 

Chiral modifiers of heterogeneous catalysts can function as activity promotors to minimize the influence of unmodified sites on the enantiomeric excess to obtain highly enantioselective catalysts. However, the origin on this effect is not well understood. It is investigated using a model catalyst of R‐(+)‐1‐(1‐naphthyl)‐ethylamine (R‐1‐NEA)/Pd(111) for the hydrogenation of methyl pyruvate (MP) to methyl lactate (ML). The activity of the model catalyst remains constant for multiple turnovers. No rate enhancement is found for R‐1‐NEA coverages below ∼0.5 monolayer (ML), but a significant increase is found at R‐1‐NEA coverages of ∼0.75 ML, with a rate approximately twice that of the unmodified catalyst. This is investigated using infrared spectroscopy to distinguish between MP monomers and dimers. MP titration experiments with hydrogen show a half‐order hydrogen pressure dependence, with the monomer reacting at twice the rate as the dimer. It is found that the dimer is the most abundant species on clean Pd(111), but the ratio of monomers to dimers increases as the R‐1‐NEA coverage increases due to surface crowding. The monomeric species is also found to be more stable on the crowded surface than on clean Pd(111); the chiral modifier also serves to stabilize the reactant. Finally, this model nicely explains the unusual 1‐NEA‐covergae dependence of the reactivity.