Halide perovskites are currently one of the most heavily researched emerging photovoltaic materials. Despite achieving remarkable power conversion efficiencies, perovskite solar cells have not yet achieved their full potential, with the interfaces between the perovskite and the charge‐selective layers being where most recombination losses occur. In this study, a fluorinated ionic liquid (IL) is employed to modify the perovskite/SnO2interface. Using Kelvin probe and photoelectron spectroscopy measurements, it is shown that depositing the perovskite onto an IL‐treated substrate results in the crystallization of a perovskite film which has a more n‐type character, evidenced by a decrease of the work function and a shift of the Fermi level toward the conduction band. Photoluminescence spectroscopy and time‐resolved microwave conductivity are used to investigate the optoelectronic properties of the perovskite grown on neat and IL‐modified surfaces and it is found that the modified substrate yields a perovskite film which exhibits an order of magnitude lower trap density than the control. When incorporated into solar cells, this interface modification results in a reduction in the current–voltage hysteresis and an improvement in device performance, with the best performing devices achieving steady‐state PCEs exceeding 20%.
Hybrid organometal halide perovskites are known for their excellent optoelectronic functionality as well as their wide‐ranging chemical flexibility. The composition of hybrid perovskite devices has trended toward increasing complexity as fine‐tuned properties are pursued, including multielement mixing on the constituents A and B and halide sites. However, this tunability presents potential challenges for charge extraction in functional devices. Poor consistency and repeatability between devices may arise due to variations in composition and microstructure. Within a single device, spatial heterogeneity in composition and phase segregation may limit the device from achieving its performance potential. This review details how the nanoscale elemental distribution and charge collection in hybrid perovskite materials evolve as chemical complexity increases, highlighting recent results using nondestructive operando synchrotron‐based X‐ray nanoprobe techniques. The results reveal a strong link between local chemistry and charge collection that must be controlled to develop robust, high‐performance hybrid perovskite materials for optoelectronic devices.
more » « less- NSF-PAR ID:
- 10055053
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Advanced Functional Materials
- Volume:
- 28
- Issue:
- 18
- ISSN:
- 1616-301X
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
Abstract -
Two-dimensional (2D) organic–inorganic hybrid halide perovskites exhibit unique properties, such as long charge carrier lifetimes, high photoluminescence quantum efficiencies, and great tolerance to defects. Over the last several decades tremendous progress has occurred in the development of 2D layered halide perovskite semiconductor materials and devices. Chemical functionalization of 2D halide perovskites is an effective approach for tuning their electronic properties. A large amount of effort has been made in compositional engineering of the cations and anions in the perovskite lattice. However, few efforts have incorporated rationally designed semiconducting organic moieties into these systems to alter the overall chemical and optoelectronic properties of 2D perovskites. In fact, incorporation of large conjugated organic groups in the spatially confined inorganic perovskite matrix was found to be challenging, and this synthetic challenge hinders a deeper understanding of the materials’ structure–property relationships. Recently, exciting progress has been made regarding the molecular design, optical characterization, and device fabrication of novel 2D halide perovskite materials that incorporate functional organic semiconducting building blocks. In this article, we provide a timely review regarding this recent progress. Moreover, we discuss successes and current challenges regarding the synthesis, characterization, and device applications of such hybrid materials and provide a perspective on the true future promise of these advanced nanomaterials.more » « less
-
more » « less
Abstract The recent development of quasi‐2D perovskite solar cells have drawn significant attention due to the improved stability of these materials and devices against moisture compared to their 3D counterparts. However, the optoelectronic properties of 2D perovskites need to be optimized in order to achieve high efficiency. In this work, the effect of spacer cations, i.e., phenethylammonium (PEA), 4‐fluorophenethylammonium (F‐PEA), and 4‐methoxyphenethylammonium (MeO‐PEA) on the optoelectronic properties and device performance of quasi‐2D perovskites is systematically studied. It is observed that both larger and more hydrophobic cations can improve perovskite stability against moisture, while larger size can adversely influence the device performance. Interestingly, with F‐PEA or MeO‐PEA, distribution of
n value can be shifted toward high 3D content in quasi‐2D perovskite layers, which enables lower bandgaps and possibly lower exciton binding energy. Due to the best charge transport and lowest bandgap, the F‐PEAI‐based quasi‐2D perovskite (n = 5) solar cell shows a highest power conversion efficiency (PCE) of 14.5% with excellent stability in air with a humidity of 40–50%, keeping 90% of the original PCE after 40 d. It is believed that the approach may open a way for the design of new organic spacer cations for stable low‐dimensional hybrid perovskites with high performance. -
The remarkable optoelectronic properties of metal halide perovskites have generated intense research interest over the last few years. The ability to control and manipulate the crystallisation and stoichiometry of perovskite thin-films has allowed for impressive strides in the development of highly efficient perovskite solar cells. However, being able to effectively modify the interfaces of metal halide perovskites, and to controllably p- or n-type dope the surfaces, may be key to further improvements in the efficiency and long-term stability of these devices. In this study, we use surface doping of the mixed-cation, mixed-halide perovskite FA 0.85 MA 0.15 Pb(I 0.85 Br 0.15 ) 3 (FA – formamidinium; MA – methylammonium) to improve the hole extraction from the perovskite solar cell. By treating the surface of the perovskite film with a strongly oxidizing molybdenum tris(dithiolene) complex, we achieve a shift in the work function that is indicative of p-doping, and a twofold increase in the total conductivity throughout the film. We probe the associated interfacial chemistry through photoelectron and solid-state nuclear magnetic resonance spectroscopies and confirm that charge-transfer occurs between the perovskite and dopant complex. The resulting p-doped interface constitutes a homojunction with increased hole-selectivity. With charge-selective layers, we show that this surface doping enhances the device performance of perovskite solar cells resulting in steady-state efficiencies approaching 21%. Finally, we demonstrate that a surface treatment with this dopant produces the same effect as the commonly employed additive 4- tert butylpyridine ( t BP), allowing us to achieve “ t BP-free” devices with steady-state efficiencies of over 20%, and enhanced thermal stability as compared to devices processed using t BP. Our findings therefore demonstrate that molecular doping is a feasible route to tune and control the surface properties of metal halide perovskites.more » « less
-
more » « less
Abstract Organometal halide perovskites have powerful intrinsic potential to drive next‐generation solar technology, but their insufficient thermomechanical reliability and unproven large‐area manufacturability limit competition with incumbent silicon photovoltaics. This work addresses these limitations by leveraging large‐area processing and robust inorganic hole transport layers (HTLs). Inverted perovskite solar cells utilizing NiOxHTLs deposited by rapid aqueous spray‐coating that outperform spin‐coated NiOxand lead to a 5× improvement in the fracture energy (
G c), a primary metric of thermomechanical stability, are presented. The morphology, chemical composition, and optoelectronic properties of the NiOxfilms are characterized to understand and optimize compatibility with an archetypal double cation perovskite, Cs.17FA.83Pb(Br.17I.83)3. Perovskite solar cells with sprayed NiOxshow higher photovoltaic performance, exhibiting up to 82% fill factor and 17.7% power conversion efficiency (PCE)—the highest PCE reported for inverted cell with scalable charge transport layers—as well as excellent stability under full illumination and after 4000 h aging in inert conditions at room temperature. By utilizing open‐air techniques and aqueous precursors, this combination of robust materials and low‐cost processing provides a platform for scaling perovskite modules with long‐term reliability.
